A2B Electronics MyM-3S Micro Master Manuale utente
11
MyM-3S Micro Master
Installation Guide
design for TV
English
22
1. Introduction
2. Unpacking the unit
3. Connections and indications
4. IP settings
5. Menus and settings
5.1 Overview menu
5.2 Input settings
5.3 Output settings
5.4 Service management
5.5 CI menu
5.6 System options
6. Installation and Configuration examples
7. Technical specification MyM-3S
8. Declaration of conformity
9. Abbreviations
English
CONTENT
33
Thank you for purchasing an A2B Electronics product. The MyM-3S is a revolutionary solution
for reception and modulation of satellite transmitted TV-content into an analogue format suited
for small SMATV networks where cost efficiency and high quality is required.
The MyM-3S receives DVB-S and DVB-S2 transmissions.
The MyM-3S unit is delivered with hardware and software that supports DVB-S/S2 reception,
MPEG2/MPEG4 decoding, DSB RF modulation with NICAM or A2 audio, IP control and
management.
The MyM-3S can be upgraded for enhanced functionality by software upgrades.
Software upgrades are available from A2B Electronics web site.
A2B Electronics AB
Phone: +46 (0)141 229115
E-mail: [email protected]
Visit our web site www.a2b.se for more information.
English
1 Introduction
44
The following items are included in the package:
Amount Description
1 MyM-3S Micro Master
1 Installation guide
2 Power supply 12 V
Every unit is quality controlled by us before delivery. Should any items be missing when unpacking,
please contact our support service (see page 3 for contact info).
English
Important information about power supply to
MyM-3S unit
To avoid problems with theMyM-3S its is
important to use the supplied power supply.
Operation with other types of power supplies will
void the warranty. (See picture to the right).
NOTE! Never connect two MyM-3S units to one
power supply. This may cause damage to your
MyM-3S.
2 Unpacking the unit
55
English
1. Satellite input 1 Connect one satellite (LNB) input here
2. Satellite input 2 Connect second satellite (LNB) input here
3. Power connector Connect the supplied power supply to this connector
4. Common Interface 1 Insert a Common Interface module into this slot
(Supports decryption for Channel 1 and 2)
5. Common Interface 2 Insert a Common Interface module into this slot
(Supports decryption for Channel 3)
6. Ethernet port RJ-45 port for 10/100 baseT Ethernet. Connect your
PC to this port for management and upgrades.
7. RF-output Combined 3 channel RF-output for connection to
your SMATV network.
8. Indicator LED Status indicator
1 2 34567
8
3 Connections and indications
6
The MyM-3S has an embedded web server
allowing standard web browsers (Internet
Explorer, Firefox, Opera etc.) to connect to
the unit for settings and management.
No controller software is needed. The MyM-
3S has by default a static IP address for
connecting your PC to the unit.
The MyM-3S is delivered with the default IP
address: 192.168.0.20.
First time installation requires that you set a
static IP address on your computer. For
example set your PC to IP address:
192.168.0.19 and Net mask: 255.255.255.0
English
4 IP settings
TCP/IP settings for Windows XP (setting your PC to 192.168.0.19)
Select ”Start”, ”Control panel” and ”Network connections”. Next select “Network and Internet
settings”. ”Right click” on [Settings for local network] and select [Properties].
In Properties select [Internet protocol
(TCP/IP)] and [Properties].
77
English
Select [Use this IP adress] and write:
192.168.0.19 and select [Net mask]
255.255.255.0. Click [OK] and then click
[Close].
NOTE! For PC with other Operating Systems
(OS) than Windows, please consult the Owners
manual for your PC for [IP/Network settings].
Connecting your PC to the MyM-3S
Connect the MyM-3S to the supplied DC power
supply.
See section 6 for installation.
Next connect your PC to the MyM-3S with a network
cable.
Start your web browser (Internet Explorer, Firefox,
Opera etc.) and write the IP address 192.168.0.20 in
the address field of your browser.
Settings of IP address
Click the [System options] menu and
then press [IP Settings] to set a new IP
address, Netmask and Gateway for the
MyM-3S.
4 IP settings (continued)
8
English
5.1 Overview menu
[Current settings]
Contains information of current input and
output signals, if the tuners are locked to
a signal, firmware version, bootloader
version, hardware revision, serial number
and current IP Network settings.
All necessary settings can be made in the web GUI via a web browser. When first connection is
made with the MyM-3S following overview menu will appear.
5 Menus and settings
[Software options]
In this menu you can see which
software options that are
activated.
To continue with settings click the [Input] name in the banner.
99
English
5.2 Input settings
As the MyM-3S contains 2 separate
tuners, start by selecting either [Tuner 1]
or [Tuner 2]. Select the modulation type
you want to receive. By selecting DVB-S2
you also can select between QPSK, 8PSK
or 16 QAM.
Set the Polarisation. Voltage, FEC and 22
kHz tone should normally be set to “Auto”
if you have connected the MyM-3S to a
Universal LNB or a switch with same
functionality as a Universal LNB.
Note! Inverted spectrum is sometimes
used in C-band transmissions and is set
automatically by auto detection.
Finally enter the correct Symbol rate and press [Set] and then enter the Transponder frequency
and press [Set]. The available services will now be presented in the [Service Management]
menu. We suggest that you consult: http://en.kingofsat.net/ or another web site for correct
parameters for the services you intend to use.
The input level should be higher than -65 dBm, preferably more than -50 dBm and max -25 dBm
and C/N should read more than 10 dB.
5 Menus and settings (continued)
10
English
5.3 Output settings
Modulation/
Band
Start the output setup by selecting which band
you want to use. You can select VHF-7, VHF-
8 and UHF. VHF-7 and VHF-8 corresponds to
7 and 8 MHz bandwidth. After selection press
[Set].
Frequency
For each of the 3 possible output channels,
set the desired output channel or frequency.
Channel Indicator Name
You can set the “Channel Indicator name” by
your personal preference. The Channel
Indicator will enable you to detect on a TV-
screen which programs that are transmitted
from the MyM-3S. Press [Set] after each
entering.
National/
Subtitle/
Type
Set type of subtitling to Normal or for Hearing
Impaired or None
National settings enables language and
regional settings depending of the region the
MyM-3 S is installed in, or which parameters
you want to use for the output.
Language
Select subtitling language. Depends of
received languages in the satellite signal.
Priority
Set DVB or Teletext subtitling as default
selection.
.
5 Menus and settings (continued)
Indice
Altri manuali A2B Electronics Ricevitore TV
