A2B Electronics MyM Pro T2 Manuale utente
MyM Pro T2 Installation guide
22
1. Introduction
2. Unpacking the unit
3. Connections and indications
4. IP settings
5. Menus and settings web ui
5.1 Overview menu
5.2 Input settings
5.3 Output settings
5.4 Service management
5.5 CI menu
5.6 System options
6. Installation and Configuration examples
7. Technical specification MyM Pro T2
8. Declaration of conformity
9. Abbreviations
English
CONTENT
33
Thank you for purchasing an A2B Electronics product. The MyM Pro T2 is a
revolutionary solution for reception and modulation both from satellite or from
terrestrially transmitted TV content into an analogue format suited for small
SMATV networks where cost efficiency and high quality is required.
The MyM Pro T2 has a multifunctional tuner that receives DVB-S/S2 and DVB-T/T2
transmissions.
The MyM Pro T2 unit is delivered with hardware and software that supports
MPEG2/MPEG4 decoding, HD downscaling, DSB RF modulation with NICAM or A2
audio, IP control and management.
The MyM Pro T2 can be upgraded for enhanced functionality by software upgrades.
Software upgrades are available from A2B Electronics web site.
A2B Electronics AB
Phone: +46 (0)141 229115
E-mail: [email protected]
Visit our web site www.a2b.se for more information.
English
1 Introduction
44
The following items are included in the package:
Amount Description
1MyMProT2
1Quickguide
Every unit is quality controlled by us before delivery. Should any items be missing when
unpacking, please contact our support service (see page 3 for contact info).
English
2 Unpacking the unit
44
55
English
1. Antenna input 1 Connect the satellite/terrestrial signal for Ch1 and Ch2
here
2. Antenna input 2 Connect the satellite/terrestrial signal for Ch3 here
3. Common Interface 1 Insert a Common Interface module into this slot
(Supports decryption for Channel 1 and 2)
4. Common Interface 2 Insert a Common Interface module into this slot
(Supports decryption for Channel 3)
5. Common Interface 3 Insert a Common Interface module into this slot
(Supports decryption for Channel 4 and 5)
6. Common Interface 4 Insert a Common Interface module into this slot
(Supports decryption for Channel 6)
7 and 8. Ethernet ports RJ-45 port for 10/100 baseT Ethernet. Connect your
PC to these ports for management and upgrades.
9. RF-output(s) Combined 3 channel RF outputs for connection to
your SMATV network.
10. Indicator LED(s) Status indicator. Green flashing LED says all channels
are OK.
Red flashing LED says one or more channels are not
decoding video.
NOTE!If only two channels are used the Video WD
shall be set to ”OFF”for the non used channel to
get green LED (see page 12)
12
34
5
7
9
3 Connections and indications
68
10
6
The MyM Pro T2 has an embedded
web server allowing web browser
Internet Explorer to connect to the
unit for settings and management.
No controller software is needed. The
MyM Pro T2 has by default static IP
address(es) for connecting your PC to
the unit.
NOTE! MyM Pro T2 is only
approved with Internet Explorer
as web browser.
The MyM Pro T2 is delivered with the
default IP address: 192.168.0.20 for
port 1 and 192.168.0.21 for port 2 in
6T.
First time installation requires that you
set a static IP address on your
computer. For example set your PC to
IP address: 192.168.0.19 and Net
mask: 255.255.255.0
English
4 IP settings
TCP/IP settings for Windows XP (setting your PC to 192.168.0.19)
Select ”Start”, ”Control panel” and ”Network connections”. Next select “Network
and Internet settings”. ”Right click” on [Settings for local network] and select
[Properties].
In Properties select [Internet protocol
(TCP/IP)] and [Properties].
77
English
Select [Use this IP adress] and write:
192.168.0.19 and select [Net mask]
255.255.255.0. Click [OK] and then click
[Close].
NOTE! For PC with other Operating
Systems (OS) than Windows, please
consult the Owners manual for your PC
for [IP/Network settings].
Connecting your PC to the MyM Pro T2
Connect the MyM Pro T2 double power cords to a
wall outlet.
See section 6 for installation.
Next connect your PC to the MyM Pro T2 with a
network cable.
Start your web browser 1) and write the IP address
192.168.0.20 and 192.168.0.21 for second port *)
in the address field of your browser.
1) MyM Pro is only approved with Internet
Explorer
Settings of IP address
Click the [System options]
menu and then press [IP
Settings] to set a new IP
address, Netmask and
Gateway for the MyM Pro T2.
4 IP settings (continued)
*) MyM Pro 6T
8
English
5.1 Overview menu
Current settings
Contains information of current
input and output signals, if the
tuners are locked to a signal,
firmware version, bootloader
version, hardware revision, serial
number and current IP Network
settings.
All necessary settings can be made in the web GUI via a web browser. When first
connection is made with the MyM Pro T2 following overview menu will appear.
5 Menus and settings
Software options
In this menu you can see
which software options that
are activated.
To continue with settings click the [Input] name in the banner.
Installation overview
In this menu you can see all MyM
Pro units when connected to a
switch and also see EXM/OXM
units that are connected to the
same switch.
99
English
5.2 Input settings
As the MyM Pro T2 contains
”multituner” start by
selecting either DVB-T/T2 or
DVB-s/S2. After that you
choose [Tuner 1] or [Tuner
2] for settings of the tuner
parameters.
Tuner 1 provides the service
list for RF output Ch1 and
Ch2. Tuner 2 provides the
service list for RF output
Ch3.
[Bandwidth] can be
selected between 6, 7 or 8
MHz. Select input channel
from [Channel name] scroll
list or write the center
frequency of the wanted Mux
and press [Set].
If you have an MyM Pro 6T
proceed with next two tuners
[Tuner 3] and [Tuner 4]
after moving the TP cable to
the other RJ 45 port (if not
using switch). Tuner 3
provides the service list for
RF output Ch4 and Ch5.
Tuner 4 provides the service
list for RF output Ch6.
NOTE! Don’t press [Set] if
channel is chosen from
the scroll list.
5 Menus and settings (continued)
1010
English
5.2 Input settings cont.
For receiving from satellite, start
with chosing [Tuner 1] or
[Tuner 2]. Tuner 1 provides the
service list for RF output Ch1
and Ch2. Tuner 2 provides the
service list for RF output Ch3.
The tuner can also be
”Disabled”.
Select the actual Input
parameters for the satellite
transponder you receive.
After the tuner has locked you
can read the values for
[Locked], [Level] and [C/N].
If you have an MyM Pro 6S
proceed with next two tuners
[Tuner 3] and [Tuner 4] after
moving the TP cable to the other
RJ 45 port (if not using switch).
Tuner 3 provides the service list
for RF output 4 and 5. Tuner 4
provides the service list for RF
output 6.
5 Menus and settings (continued)
Indice
Altri manuali A2B Electronics Ricevitore TV
