Aaeon PCM-5335 Manuale utente

PCM-5335

All In One NS Geode GX1 with

SVGA/LCD/Ethernet Interface

PC/104 CPU Module

This document is copyrighted, 2001, by AAEON Co., Ltd. All rights

are reserved. The original manufacturer reserves the right to make

improvements to the products described in this manual at any time

without notice.

No part of this manual may be reproduced, copied, translated or

transmitted in any form or by any means without the prior written

permission of the original manufacturer. Information provided in this

manual is intended to be accurate and reliable. However, the original

manufacturer assumes no responsibility for its use, nor for any

infringements upon the rights of third parties which may result from its

use.

Acknowledgements

AMD is a trademark of Advanced Micro Devices, Inc.

Award is a trademark of Award Software International, Inc.

Cyrix is a trademark of Cyrix Corporation.

IBM, PC/AT, PS/2 and VGA are trademarks of International Business

Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows®is a registered trademark of Microsoft Corp.

RTL is a trademark of Realtek Semiconductor Co., Ltd.

C&T is a trademark of Chips and Technologies, Inc.

UMC is a trademark of United Microelectronics Corporation.

Winbond is a trademark of Winbond Electronics Corp.

STPC is a trademark of SGS Thomson Corp.

For more information on this and other AAEON products, or technical

supportand service , please visit our website at:

http://www.aaeon.com.tw

This manual is for the PCM-5335.

Part No. 2087533500

1st Edition Printed in Taiwan December 2001

Packing list

Before you begin installing your card, please make sure that the

following materials have been shipped:

• 1 PCM-5335 All-in-one single board computer

• 1 Start-up manual

• CD-ROM or Disks for utility, drivers, and manual (in PDF format)

• 1 2.5" IDE flat cable, 44-pin to 44-pin

• 1 PS/2 keyboard & mouse cable

• 2 serial port cables

• 1 cable 6P - 6P

• 1 parallel cable

• 1 26-34 pin FDD cable converter

• 1 floppy cable, for 3.5" FDD only

• 1 FDD flat cable

• 1 VGA cable

• 1 LAN cable

• 1 warranty certificate

If any of these items are missing or damaged, contact your distributor

or sales representative immediately.

Contents

Chapter 1 General Information 1

1.1 Introduction....................................................................... 2

1.2 Features ............................................................................. 3

1.3 Specifications .................................................................... 4

1.3.1 Standard SBC functions .............................................. 4

1.3.2 VGA function .............................................................. 4

1.3.4 Ethernet function ........................................................ 5

1.3.5 Solid state disk ............................................................. 5

1.3.6 Mechanical and environmental ....................................5

1.4 Board dimensions ............................................................ 6

Chapter 2 Installation 7

2.1 Connectors ....................................................................... 8

2.2 Locating connectors ........................................................ 9

2.3 Safety precautions .......................................................... 10

2.4 Ethernet connector (CN1) ............................................ 10

2.4.1 Ethernet connector (CN1) ......................................... 10

2.4.2 Network boot............................................................. 10

2.5 LCD display connector (CN2) ...................................... 10

2.6 Serial ports

(CN3: COM1; CN4: COM2/RS-232;

CN18: COM2/RS-422/485) ......................................... 11

2.6.1 RS-232 connection (COM1: CN3) ............................ 11

2.6.2 RS-232/422/485 connection

(COM2: CN4: RS-232; CN18: RS-422/485) ..................... 11

2.7 EIDE HDD connector (CN5) ....................................... 12

2.7.1 Connecting the hard drive ......................................... 12

2.8 PC/104 connector (CN6) ............................................... 12

2.9 Parallel port connector (CN7) ...................................... 13

2.10 Backlight connector (CN8)........................................... 13

2.11 VGA connector (CN9) ................................................... 13

2.11.1 CRT display connector (CN9) ................................. 13

2.12 Main power (+5 V / +12 V) connector (CN11) .......... 13

2.13 PS/2 keyboard/mouse connector (CN12) ................... 1 4

2.14 FDD connector (CN14) ................................................. 14

2.14.1 Connecting the floppy drive ..................................... 14

2.15 CompactFlash™ socket (CN16) .................................. 15

2.16 USB connector (CN17) ................................................. 15

2.17Multifunction Jumpers (MJ1)......................................16

2.17.1 Auxilary power connector (MJ1-A)........................16

2.17.2 Fan connector (MJ1-B) ........................................... 17

2.17.3 Reset button connector (MJ1-C) ............................. 17

2.17.4 IR connector (MJ1-D) ............................................ 17

2.17.5 Watchdog timer configuration (MJ1-E) ................... 17

2.18 SO DIMM socket (Slot1) ............................................. 18

2.18.1 Installing SODIMMs ............................................... 18

Chapter 3 Software Configuration 21

3.1 Introduction ..................................................................... 22

3.2 Utility CD disk ................................................................ 22

3.3 VGA display software configuration ............................ 22

3.4 Connections for two standard LCDs ........................... 24

3.4.1 Connections for Toshiba LTM10C042(640 x 480 TFT

color LCD) ......................................................................... 24

3.4.2 Connections for Toshiba LTM12C275A

(800 x 600 TFT color LCD) .............................................. 25

Chapter 4 Award BIOS Setup 27

4.1 System test and initialization ........................................ 28

4.1.1 System configuration verification .............................. 28

4.2 Award BIOS setup ......................................................... 29

4.2.1 Entering setup ............................................................ 29

4.2.2 Standard CMOS setup .............................................. 30

4.2.3 BIOS features setup .................................................. 31

4.2.4 Chipset features setup ............................................... 32

4.2.5 Power management setup ......................................... 33

4.2.6 PnP/PCI configuration .............................................. 34

4.2.7 Integrated peripherals ................................................ 35

4.2.8 Change password ...................................................... 36

4.2.9 Save & exit setup ...................................................... 37

4.2.10 Exit without saving .................................................. 37

Chapter 5 PCI Bus Ethernet Interface 39

5.1 Introduction..................................................................... 40

5.2 Installation of Ethernet driver ..................................... 40

5.2.2 Installation for Windows 98/2000 .............................. 41

5.3 Further information ........................................................ 44

Chapter 6 SVGA Setup 45

6.1 Introduction..................................................................... 46

6.1.1 Chipset ....................................................................... 46

6.1.2 Display memory ........................................................ 46

6.2 Installation of SVGA driver .......................................... 46

6.2.1 Installation for Cyrix MediaGX Certified drivers for

Windows 95/98. Insert the disk into the CD-ROM drive. .. 47

6.2.2 Installation for Windows NT ..................................... 50

6.3 Further information ........................................................ 56

Appendix A Programming the Watchdog Timer 57

A.1 Programming the watchdog timer ............................... 58

Appendix B Installing PC/104 Modules 61

B.1 Installing PC/104 modules ............................................ 62

Appendix C Pin Assignments 65

C.1 Ethernet connector (CN1) ............................................ 66

C.2 LCD connector (CN2) ................................................... 67

C.3 COM1 connector (CN3) ............................................... 68

C.4 COM2 connector (CN4) ............................................... 68

C.5 EIDE hard drive connector (CN5) .............................. 69

C.6 PC/104 connector (CN6) ............................................... 70

C.7 Parallel port connector (CN7) ...................................... 70

C.8 Backlight connector (CN8)........................................... 71

C.9 VGA connector (CN9) ................................................... 71

C.10 Main power (+5 V) connector (CN11) ........................ 72

C.11 PS/2 keyboard/mouse connector (CN12) ................. 72

C.12 FDD connector (CN14) ................................................. 73

C.13 CompactFlash™ socket (CN16) .................................. 74

C.14 COM2 connector for 422/485 (CN18) ........................ 76

C.15 Multifunction Jumpter (MJ1) ...................................... 76

Appendix D System Assignments 79

D.1 System I/O ports ............................................................ 80

D.2 DMA channel assignments ........................................... 81

D.3 Interrupt assignments ................................................... 82

D.4 1st MB memory map ..................................................... 83

Figures

Figure 1-1: PCM-5335 dimensions................................................................6

Figure 2-1: Locating connectors (component side) ..................................... 9

Figure 2-2: Locating connectors (solder side) ............................................. 9

Figure 3-1: Contents of the PCM-5335 Series utility disk.............................22

Figure 3-2: BIOS VGA setup screen .............................................................. 23

Figure 4-1: BIOS setup program initial screen ............................................. 29

Figure 4-2: CMOS setup screen ................................................................... 30

Figure 4-3: BIOS features setup ................................................................... 31

Figure 4-4: Chipset features setup ............................................................... 32

Figure 4-5: Power management setup ......................................................... 33

Figure 4-6: PnP/PCI configuration ................................................................ 34

Figure 4-7: Integrated peripherals ................................................................ 35

Figure B-1: PC/104 module mounting diagram ........................................... 63

Figure B-2: PC/104 module dimensions (mm) (±0.1) ................................. 63

Figure C-1: CompactFlash™ socket ............................................................ 75

Tables

Table 2-1: Connectors ...................................................................................................... 8

Table 2-2: Serial port connections (COM1, COM2) ........................................................ 11

Table 2-3: Serial port default settings ............................................................................ 12

Table B-1: PCM-5335 PC/104 connectors (CN6)...........................................................64

Table C-1: Ethernet connector (CN1) ............................................................................. 66

Table C-2: LCD connector (CN2) .................................................................................... 67

Table C-3: COM1 connector (CN3) ................................................................................ 68

Table C-4: COM2 connector (CN4) ................................................................................ 68

Table C-5: EIDE hard drive connector (CN5) ................................................................. 69

Table C-7: Parallel port connector (CN7) ....................................................................... 70

Table C-9: VGA connector (CN11) ................................................................................ 71

Table C-8: Backlight connector (CN8) ............................................................................ 71

Table C-10: Main power (+5 V) connector (CN11) ........................................................ 72

Table C-11: PS/2 keyboard/mouse connector (CN12) ................................................... 72

Table C-12: FDD connector (CN14) ............................................................................... 73

Table C-13: CompactFlash™ socket (CN16) ................................................................. 74

Table C-14: COM2 connector for 422/485 (CN18) ........................................................ 76

Table C-15: MJ1-A, -5 V, -12 V input ............................................................................. 76

Table C-16: MJ1-B, fan connector ................................................................................. 76

Table C-18: MJ1-D, IR connector .................................................................................... 77

Table C-19: MJ1-E, watchdog jumper ............................................................................ 77

Table C-17: MJ1-C, reset button ..................................................................................... 77

Table D-1: System I/O ports ........................................................................................... 80

Table D-2: DMA channel assignments ........................................................................... 81

Table D-3: Interrupt assignments ................................................................................... 82

Table D-4: 1st MB memory map ...................................................................................... 83

Altri manuali per PCM-5335

Indice

Altri manuali Aaeon Hardware per computer

Aaeon

Aaeon PCM-8300 Manuale utente

Aaeon

Aaeon NanoCOM-WHU Manuale utente

Aaeon

Aaeon PICO-BT01 Manuale utente

Aaeon

Aaeon HSB-800P Manuale utente

Aaeon

Aaeon UPS-EDGE-EHL01 Manuale utente

Aaeon

Aaeon AEC-6613 Manuale utente

Aaeon

Aaeon AEC-6637 Manuale utente

Aaeon

Aaeon SBC-555 Manuale utente

Aaeon

Aaeon BOXER-6640M Manuale utente

Aaeon

Aaeon SBC-860 Manuale utente

Aaeon

Aaeon GENE-EHL7 Manuale utente

Aaeon

Aaeon GENE-APL6 Manuale utente

Aaeon

Aaeon SBC-657 Manuale utente

Aaeon

Aaeon BOXER-8120AI Manuale utente

Aaeon

Aaeon UP Vision Plus X Manuale utente

Aaeon

Aaeon PCM-6896 Manuale utente

Aaeon

Aaeon SBC-411 Manuale utente

Aaeon

Aaeon PCM-9150 Manuale utente

Aaeon

Aaeon UP Squared Pro Manuale utente

Aaeon

Aaeon NEZHA-N97 Manuale utente

Aaeon

Aaeon PCM-6892 Rev.B Manuale utente

Aaeon

Aaeon ETX-701 Manuale utente

Aaeon

Aaeon HSB-800I Manuale utente

Aaeon

Aaeon HSB-660S/I Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente