Aban Technology HIGH SPEED DOME CAMERA Manuale utente
User Manual
27X AF Zoom
HIGH SPEED DOME CAMERA
2
3
Ⅰ CAUTION --------- 4
Ⅱ INTRODUCTION OF PRODUCTS --------- 6
Ⅲ DIRECTIONS FOR USE --------- 14
Ⅳ FUNCTIONAL SETTING BY THE KEYBOARD --------- 26
Ⅴ OSD MESSAGE DISCRIPTION --------- 29
Ⅵ TROUBLE SHOOTING --------- 31
Ⅶ DIMENSION --------- 33
Ⅷ ASSEMBLY --------- 35
Ⅸ SPECIFICATION --------- 38
Table of contents
4
Thank you for purchasing our product. Please operate the product after being
fully aware of the manual. Pease contact us if you have any queries.
Precaution
Note the following matters before the installation of the product.
Avoid the following places for the installation.
Ⅰ. CAUTION
A high/low temperature: Using indoor-cameras
in the places of +50°C~ -10°C can cause
troubles and lower its capacity.
Snow, rain and wet: Humidity or water and
any liquid inside-camera can cause troubles.
Oil, gas: Oil and gas can damage the camera
as they go through the cameras.
Vibration, shock: They bring on problems or
errors of the camera.
Direct light, exposure to the air: In the case of
that sets indoor- cameras outside where the
weather is changeable, it can cause problems.
Closing to High frequency and electric power
lines: Setting the camera up around
electromagnetic units or power supplier can
bl
5
Caution in Use
Do not disassemble the unit and put alien substances in the unit.
- Disassembling the unit or putting alien substances such as a metal can make the
camera defective.
- Make sure of power switch-off before the installation.
: Ensure power switch-off and check the voltage the camera before the installation.
- Do not give the unit a shock and an operation.
: Giving a strong shock or an excessive power on the button, terminal can cause
problem.
This product has been designed and manufactured in accordance with the harmonized
European standards, following the provisions of the below stated directives.
Electromagnetic Compatibility Directive 89/336/EEC
(EN60065:1998, EN61000-6-3:2001, EN61000-6-1:1997)
This devise complies with part 15 of the FCC rules operation is subject to the
following two conditions: (1) This device may not cause harmful interference and
(2) This device must accept any interference received including interference that
may cause undesired operation
Caution :
①Must use AC24V power source, current intensity must be less than 1.5A and
must use a double winding transformer
②Never extend the power line from adaptor to camera.
③ Please use more thick cable than 18AWG(1.0mm), if you want to
extend the power line.
④ You must use one adaptor per one camera that is being provided.
⑤ Use extra power supplier, If you want to supply many piece of
cameras.
6
1. DESCRIPTION AND FEATURES
Description
This camera has been designed elegantly for buildings, department stores that
need to be in harmony with the interior as a high speed dome camera, including
various observation functions.
Features
☺Optical 27X Zoom Rate
Built-in 27X Zoom Camera with 12x Digital Zoom (Total 324x Zoom )
☺A low light function
Surveillance with optimum picture is possible owing to digital-slow-shutter function.
Digital-slow-shutter function is improving the CCD sensitivity by electrically lengthening
exposure time so that it should be under surveillance on the condition of 0.00005Lux in
B/W
☺Digital Noise Reduction
DNR significantly reduces the amount of low luminance noise.
☺Digital Image Stabilize
There is some tremble as zoom magnification is high, the function can compensate the
tremble.
☺HLC/User BLC Function
The HLC settings selectively eliminates high lights in a limited.
☺Auto Tilt Function
The unit can track the moving object automatically until 180° in vertical by using controller.
☺250 Preset positions
A maximum of 250 preset positions can be programmed. The preset function enables to
set where you want on monitor at any time.
☺Various auto-surveillance functions
Swing(2), Group(12 Presets), Tour(12 Groups), Spiral, Trace
☺Smart pan/tilt function
Pan and tilt speed compensation function in proportion to depth of zoom.
Ⅱ. INTRODUCTION OF PRODUCT
7
2. INSTALLATION AND CONNECTION
1) Name and function of each part
(UPPER COVER)
The camera’s body goes to
here and a power cable,
data cable, video cable,
sensor have been
connected with this
(DOME DRIVER)
A main body that has a
built-in the control units and
camera
(LOWER COVER)
Insert the body into the
upper cover, then close the
lower cover
Indoor Type Outdoor Type
8
2) Installation
SEPARATION OF LOWER
COVER
(Indoor type)
Loosen the bolt of the back
of lower cover by a
screwdriver(+), then turn the
cover as above the picture
and pull the lower cover to
the down
(Outdoor type)
Loosen the four bolts of the
lower cover, then separate.
Loosen the three bolts, the
round head shaped, of the
camera body. The three bolts
are not loosened completely
and not come up more than
1cm of the lower cover, then
separate.
Pull the cover up with
grabbing the bottom of the
camera after loosening the
three bolts
Indoor Type Outdoor Type
9
Open the connector cover, then connect
power, data, video cable and sensor
The cover is opened if user loosens the
one bolt on the connector cover by using a
screwdriver(+).
The bolts not loosened completely to
protect from missing of them.
Be careful that each cable which each
function is changed wrong
Have you connect the power cable
in the right direction ?
If yes
①RED led, in the middle of the
connector, is lighted
②Use AC24V power source and
user can use any power input that is
connected with a terminal and a
jack (But use 1 input).
10
3) How to connect equipments
Connect the image
line of a monitor
User can control maximum up to 255 cameras
connected by using the exclusive control keyboard.
User can connect it maximum up to 1.2km when
using twist pair shield cable as a connecting cable
DC12V/1A adaptor and junction box are provided
on a purchase, Junction box consists of 2 data
ports ( Each data port can be connected with
maximum up to 128 cameras and sub keyboard
terminal
Reference to the following page.
Indice
