ABB ACS 600 Istruzioni operative e di manutenzione

6

Lead the motor and mains cables through the

bottom plate.

ENSURE MAINS SUPPLY TO INSTALLATION IS OFF.

LOCK THE DISCONNECTOR TO OPEN POSITION.

ACx 600 MUST BE INSTALLED BY A COMPETENT PERSON.

IF IN DOUBT DO NOT INSTALL.

1

1. Measure the places for four screw holes.

Mark the hole positions. 2. Drill the holes.

3. Screw in the screws.

2

Position ACx 600 onto screws and securely

tighten in all four corners.

Note:

Lift ACx 600

by its chassis, not by its cover.

1. Undo the two screws. 2. Lift the lower edge

of the cover. 3. Disconnect the cable from

connector X2. Remove the cover.

STOP

FOR

INSTALLATION

OF OPTIONAL

EQUIPMENT,SEE

SEPARATE

INSTRUCTIONS

INCLUDED IN

THE DELIVERY.

4 5

1. Strip off the insulation from the motor cable

and mains cable. Twist the screen wires into

bundles. 2. Make suitable holes to motor and

mains cable grommets.

Before Starting Installation

CHECK BOX CONTENTS: ACx 601, Manual(s), Testing report, Ordered options, Quick Guide(s)

CHECK INSTALLATION SITE AMBIENT CONDITIONS: See Manual.

CHECK INSTALLATION SPACE: ACx 600 free space requirements are 300 mm above and below, 50 mm on the left and on the right.

CHECK INSTALLATION SURFACE: Vertical, smooth and solid, free from heat, damp and condensation.

CHECK ACCESSORIES NEEDED: See Manual for fuse, supply disconnecting device and cable specifications.

3

Mains cable

OUTPUT

STOP

CHECK THE

INSULATIONS

OF MOTOR,

AND MAINS

AND MOTOR

CABLE.

See Manual.

7

2.

1.

3.

2.

1.

3.

1.

2.

INPUT

Motor

cable

300 mm

free space

ACS 600 Installation Guide

ACS/ACC/ACP 601-0005-3 ... -0016-3,

-0006-5 ... -0020-5 and -0009-6 ... -0020-6

10

6-7

6-7

15

X2

1. Connect the motor cable.

2. Connect the mains cable.

Ensure proper earthings.

For minimal radio frequency

interference (RFI) at the motor

end:

1.Twisted screen:

Diameter (Ø) > 1/5 ·Length (L),

or

2. Screen 360° earthing at cable

lead-through.

LØ

8

9

Control cable installation:

1. Make hole in a control cable

grommet and lead the cable into

the unit.

2. Connect the earthing wires

and the cable shield to the

earthing terminal next to the

NIOC board.

3. Connect the control cables to

the input/output terminals.

1. Connect the control panel

cable to connector X2.

2. Replace the front cover.

10

1.

2.

2.

1.

Earthing Wires

and the cable shield 3.

300 mm

free space

ABB Industry Oy Drives P.O. Box 184 FIN-00381 Helsinki tel: +358-10 22 2000 fax: +358-10 22 22681

Code: 3AFY 59019902 R0125

Effective: 3.3.1998/EN

Standard

Input/Output

Connections: See

the

Start-up

Guide

or Manual.

X2

Altri manuali per ACS 600

3

Indice

Altri manuali ABB Azionamento CC

Manuali Azionamento CC popolari di altre marche

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuale utente

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuale elenco delle parti

Chamberlain Garog

Chamberlain Garog D Series Manuale utente

Parker

Parker PDS Series Manuale utente

Festo

Festo DGC G Series Guida all'installazione

Binks

Binks QS-5012-1-CE Manuale utente

Danfoss

Danfoss VLT 2800 Series Scheda tecnica

YASKAWA

YASKAWA CANopen SI-S3 Manuale utente

GE

GE D20A6 Manuale utente

Unex

Unex MC-D-250-1000-050W-TW Manuale utente

Geckodrive

Geckodrive G213V Manuale utente

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuale del proprietario

WEG

WEG DeviceNet CFW500 Manuale utente

Siemens

Siemens SINAMICS G Scheda tecnica

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Istruzioni operative

SOMFY

SOMFY JR RU 30 Manuale utente

Beckhoff

Beckhoff AX8911 Manuale dell'operatore

Minarik

Minarik MM300 Series Manuale utente