Acard ACP-2212P Manuale utente
ACP-2212P
User Manual
Copyright and Trademark
The information contained in this manual may be subject to change without notice.
Retailers will not be held liable for any errors that may be present in this manual.
ACARD and Mirror Smart are both registered trademarks of ACARD Technology nc.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the
United States and other countries. All trademarks are the intellectual property of their
respective owners.
The contents of this manual are protected by international copyright laws. All rights
reserved. The replication, transmission or transfer of any or all parts of this manual
using electronic or mechanical means is prohibited without ACARD's express
authorization in writing.
ACP-2212P
User Manual
Index
Chapter 1 Overvie …………………………………………………………………3
1.1 ntroduction ………………………………………………………………………3
1.2 Features …………………………………………………………………………3
1.3 Specification………………………………………………………………………4
1.4 Packaging…………………………………………………………………………4
1.5 Quick setup ………………………………………………………………………6
1.6 Hard Disk Compatibility ………………………………………………………6
Chapter 2
Installation ……………………………………………………………
…………………………………………………………… ……………………………………………………………
…………………………………………………………… 7
2.1 Hard Disk nstallation ……………………………………………………………8
2.2 Connecting the ACP-2212P to the Computer ………………………………10
Chapter 3 Setup & Operation …………………………………………………
………………………………………………… …………………………………………………
…………………………………………………12
3.1 External Appearance …………………………………………………………12
3.2 RA D Mode nstructions ………………………………………………………13
3.3 LED ndicator ……………………………………………………………………15
3.4 ACP-2212P One Touch Backup Setup………………………………………16
Chapter 4 Troubleshooting ……………………………………………………
…………………………………………………… ……………………………………………………
……………………………………………………32
Appendix 1 ACP-2212P Application …………………………………………
……………………………………………………………………………………
…………………………………………38
Appendix 2 About RAID …………………………………………………………
……………………………………………………………………………………………………………………
…………………………………………………………52
Appendix 3
Concerns the installation of the Windo s system recovery
and backup assembly ……………………………………………………………
…………………………………………………………………………………………………………………………
……………………………………………………………53
3
ACP-2212P Chapter 1 Overvie
Chapter 1 Overvie
1.1 Introduction
The ACP-2212P is the world's first ultra-slim disk mirror and backup product.
Two 2.5" SATA HDDs are used for storage and a single HDD can be used as
a backup storage device without requiring external power. t can be connected
to a computer for use through the user-friendly USB interface without requiring
rebooting of the computer. The ACP-2212P is suitable for general consumers
such as individual users, students or office workers and can be used at home,
at the office or on the move. These make it the perfect storage solution for
notebook users. The ACP-2212P can be connected externally to store
important user data and in Mirror Mode a complete backup is retained even if
one of the hard disks fails. Excellent product compatibility ensures that the
ACP-2212P can be used with most 2.5" SATA hard disks on the market. The
ACP-2212P Mirror Smart Mini (MSM) comes with a streamlined design that
suits all notebook styles currently on the market. The fashionable styling will
not only make you the envy of other users but also emphasize your expertise
in storage solutions.
1.2 Features
● Built-in ACARD ARC286 system engine chip
● No external power supply needed when used in single disk mode.
● Support for RA D 1 and Normal function (Setting change by Utility)
● Support for 2.5” SATA hard disks
● Supports automatic hard disk rebuilding
● Supports hot-swapping on USB enabled server systems
● Dual-color LED status display for hard disk and RA D functionality
● OTB (One Touch Backup) button design*
● Alarm sounds when system is damaged
● Built-in Flash ROM for faster firmware updates
* OTB is only available when used with eSBR software (easy storage, easy backup,
easy recovery)
4
ACP-2212P Chapter 1 Overvie
1.3 Specifications
● ACARD ARC286 USB to SATA control chip
● RA D Modes: RA D 1 and Normal
● Supports automatic hard disk rebuilding
● System nterface:
◆ Support for USB 2.0 B-Type with data transfer rates of up to 480Mb/Sec
● Hard Disk nterface:
◆ Support for two 2.5” SATA interfaces with data transfer rates of up to
1.5Gbps
● Error Notification: Built-in buzzer and LED indicator
● Built-in 64KB Flash ROM
● Supported Operating Systems: Windows ME/2000/NT/XP/Server 2003/
Vista, Linux, Mac OS etc.
● Dimensions: 163mm (W) x 16mm (H) x 163mm (D)
● Power Supply: nput: 100V~220V/2A; Output: 5V/2A
● Temperature:
◆ Operating: 5°C~40°C (No condensation)
◆ Non-Operating: 5°C~50°C
1.4 Packaging
● ACP-2212P x 1
● HDD Rack x 2
● Screwdriver x 1
● Packet of Screws x 1
● Support CD-ROM (eSBR, Mirror Utility, Ha! DVD) x 1
● User Manual x 1
● USB 2.0 Cable x 1
● Power Supply x 1
5
ACP-2212P Chapter 1 Overvie
Precautions
1. This product’s power supply can’t be connected to the computer
2. After a new installation the hard disk must be formatted before use. f data is
already stored on the device, its integrity can’t be guaranteed when
changing the RA D mode.
3. Loss of data due to computer viruses, power outages or human error is
unavoidable.
4. This product does not support disk hot-swapping. f a hard disk malfunctions
and needs to be replaced, please turn off the device before replacing the hard
disk.
5. n actual use the capacity of hard disk 1 (source) must be smaller or equal to
the capacity of hard disk 2 (target)
6. The eSBR utility software supports the built-in backup software in Windows
2000/XP/Vista. Please check regularly with the ACARD Technology website at
http://www.acard.com
7. Please read the manual carefully before making advanced configuration
changes to the software. Expert assistance is recommended.
8. The Ha! DVD Burner software included in the Support CD-ROM is a trial
bundled with DVD burners. To buy the full version please visit the ACARD
Technology website at http://www.acard.com
9. Names and product names are the trademarks or registered trademarks of
their respective companies.
10. The external appearance of specifications may be subject to change without
notice
1.5 Quick Setup
1. Prepare two identical 2.5” SATA hard disks.
2. Fit both hard disks with the HDD Rack Handle and screw securely into
place.
3. Open and remove the ACP-2212P front panel.
4. Take the hard disks by the Rack Handle and then insert them into theACP
-2212P system with the SATA interface facing inwards. Check that the
SATA hard disks’ data and power connectors are securely affixed to the
data and power connectors in the ACP-2212P system.
5. Replace the ACP-2212P front panel and screw securely in place.
6. Connect the power supply to the ACP-2212P and start device.
7. Connect the USB 2.0 B-type cable to the ACP-2212P.
8. Connect USB 2.0 A-type connector at the other end of the cable to the
computer’s USB interface.
9. Once the computer boots up the system will detect a hard disk named
Mirror USB Device. Partition and format the Mirror USB device if necessary.
**Attention: f only one single HDD is used and the device is not connected to
an external power supply, the HDD must be installed in the HDD 1 position. t
will not be detected by the system if installed in the HDD 2 position.
1.6 Hard Disk Compatibility
The ACP-2212P is designed for use with 2,5” SATA hard disks. The latest list
of compatible hard disks is available online from: http://www.acard.com
f your hard disk is not included in the ACARD compatibility list, please contact
us or your distributor.
6
ACP-2212P Chapter 2 Overvie
7
ACP-2212P Chapter 2 Installation
Chapter 2 Installation
ACP-2212P Main Device
Status Panel (from left to the right):
：
：：
：Back up Control Button (Available when online)
：
： ：
：Three-colored indicators showing the hard disks' power supply,
failure and data rebuilding status.
：
：：
：The two hard drives’ data access indicators
：
：：
：RA D 1 status indicator
：
：：
：Normal status indicator
：
：：
：USB 2.0 B-type interface
：
：：
：Buzzer Mute button
：
：：
：Power Supply power input jack
2.1 ACP-2212P Hard Disk Installation
1. First secure the hard disk handles included in the packaging to the hard
disks with the screws provided as shown in the picture below:
. .
.
2. Unscrew and remove the ACP-2212P front panel as shown in the picture
below:
. .
3. Now insert the SATA hard disks fitted with the hard disk handles into the
ACP-2212P along the guide rails with the front side facing upwards. Push
the hard disks until the contacts are securely attached as shown in the
picture below:
. .
**Attention: Users with only one HDD must connect it to the HDD1 port. The
device can then connected to the host computer via the USB cable and used
directly.
8
ACP-2212P Chapter 2 Installation
Note:
To fit along guide rack
HDD 1
HDD 2
9
ACP-2212P Chapter 2 Installation
4. After checking that the hard disks have been properly installed into the
ACP-2212P, replace and screw the front panel securely back into place as
shown in the picture below:
. .
5. Finally attach the anti-skid pads included with the accessories at the
indicated locations as shown in the picture below:
. .
**The above steps complete the hardware installation of the ACP-2212P
Indice
Altri manuali Acard Magazzinaggio
