Acer ConceptD 900 Manuale utente

ConceptD 900

Desktop Computer Covers:

Tower models

This revision: May 2019 V1.00

Important

This manual contains proprietary information that is protected by

subject to change without notice. Images provided herein are for

reference only and may contain information or features that do not

apply to your computer. Acer Group shall not be liable for technical

or editorial errors or omissions contained in thismanual.

Table of Contents

UPGRADING YOUR COMPUTER.............1

Installation precautions

..................1

ESD precautions

..........................................1

Required tools

..............................................1

Pre-installation instructions

.....2

Post-installation instructions

..2

System Upgrade

...................................3

Removing the left side system

cover

............................................................3

Installing the left side system

cover

............................................................4

Removing the right side

system cover

.........................................5

Installing the right side system

cover

............................................................6

Hard drives

..............................................7

Removing the 3.5-inch hard

drives

...........................................................7

Installing the 3.5-inch hard

drives

...........................................................9

Installing the 2.5-inch hard

drives

.........................................................11

Memory

.................................................... 12

Memory configuration guidelines

.......12

Removing a memory module

.13

Installing a memory module

...15

Graphic board

..................................... 16

Removing the Graphic board

Installing the Graphic board

.18

M.2 SSD module

.................................. 20

Removing the M.2 SSD module

........................................................................20

Installing the M.2 SSD module

........................................................................21

Upgrading your Computer

In this section, you will find:

•Instructions on how to replace a hardware component

UPGRADING YOUR COMPUTER -

UPGRADING YOUR COMPUTER

Installation precautions

Before you install any computer component, we recommend

that you read the following sections. These sections contain

important ESD precautions along with pre-installation and

post-installation instructions.

ESD precautions

Electrostatic discharge (ESD) can damage your processor,

disk drives, expansion boards, and other components.

Always observe the following precautions before you install a

computer component:

1. Do not remove a component from its protective

packaging until you are ready to install it.

2. Wear a wrist grounding strap and attach it to a metal

part of the computer before handling components. If a

wrist strap is not available, maintain contact with the

computer throughout any procedure requiring ESD

protection.

Required tools

In performing the component replacement process, you will

need the following tools:

•Philips screwdriver

•Hex screwdriver

•Flat screwdriver

•Scissors

Note

The screws for the different components vary in size. During the

disassembly process, group the screws with their corresponding

components to avoid mismatches when putting back the components.

- UPGRADING YOUR COMPUTER

Pre-installation instructions

Always observe the following before you install any

component:

1. Make sure that the ODD and card reader slot is empty.

2. Turn off the power to the computer and all peripherals.

3. Unplug the power cord from the computer.

4. Unplug the network cable and all connected peripheral

devices from the computer.

5. Place the computer on a flat, steady surface.

6. Open your computer according to the instructions on

removing the left side system cover on page 4 and

removing the right side system cover on page 5.

7. See the following sections for specific instructions on

the component you wish to install.

Post-installation instructions

Observe the following after installing a computer component:

1. See to it that the components are installed according to

the step-by- step instructions in their respective

sections.

2. Replace any expansion boards or peripherals that you

removed earlier.

3. Replace the system covers. See Installing the left side

system cover on page 5 and installing the right side

system cover on page 6.

4. Connect the necessary cables.

5. Turn on your computer.

Warning

Not turning off the computer properly before you start installing the

components may cause serious damage. Do not attempt the

procedures described in the following sections unless you are a

qualified service technician.

UPGRADING YOUR COMPUTER -

System Upgrade

Removing the left side system cover

1. Before you proceed, make sure that you have turned

off your computer and all peripherals connected to it.

Read the Pre- installation instructions on page 2.

2. Remove the two screws that secure the system cover

to the computer.

3. Slide the cover toward the back of the computer and

pull away from the side of the computer.

4. Set the cover aside for re-installation later.

- UPGRADING YOUR COMPUTER

Installing the left side system cover

1. Align the cover to the sides of the computer and slide

the cover toward the front of the computer.

2. Secure the cover with two screws.

3. Observe the Post-installation instructions on page 2.

UPGRADING YOUR COMPUTER -

Removing the right side system cover

1. Before you proceed, make sure that you have turned

off your computer and all peripherals connected to it.

Read the Pre- installation instructions on page 2.

2. Remove the two screws that secure the system cover

to the computer.

3. Slide the cover toward the back of the computer and

pull away from the side of the computer.

4. Set the cover aside for re-installation later.

-UPGRADING YOUR COMPUTER

Installing the right side system cover

1. Align the cover to the sides of the computer and slide

the cover toward the front of the computer.

2. Secure the cover with two screws.

3. Observe the Post-installation instructions on page 2.

Indice

Altri manuali Acer Scrivania

Acer

Acer Aspire E600 Manuale utente

Acer

Acer Aspire EL Manuale utente

Acer

Acer Aspire T630 Manuale utente

Acer

Acer Veriton 7600GT Manuale utente

Acer

Acer Aspire T120 Manuale utente

Acer

Acer Lenovo 3000 J Series Manuale utente

Acer

Acer NITRO 50 Manuale utente

Acer

Acer Aspire G3-605 Manuale utente

Acer

Acer Aspire M3420 Manuale utente

Acer

Acer AcerPower M4 Manuale utente

Acer

Acer Aspire S 24 Manuale utente

Acer

Acer Aspire T670 Manuale utente

Acer

Acer Veriton FP series Manuale utente

Acer

Acer AcerPower 4100 Manuale utente

Acer

Acer Veriton 5800 Guida all'installazione

Acer

Acer Veriton 5100 Manuale utente

Acer

Acer Veriton X4610G Manuale utente

Acer

Acer Aspire S Series Manuale utente

Acer

Acer Veriton L4610G Manuale utente

Acer

Acer AcerSystem Manuale utente

Acer

Acer Aspire M5200 Manuale utente

Acer

Acer Aspire T180 Manuale utente

Acer

Acer ASPIRE X5400 Manuale utente

Acer

Acer Veriton 7500GE Series Manuale utente

Manuali Scrivania popolari di altre marche

HP m9060n - Pavilion - Elite Scheda tecnica

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

HP Presario SV7000 - Desktop PC Manuale utente

HP ProDesk 400 G5 Manuale

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente