Acer ALW-3016 Manuale utente
16-port 10/100Mbps Switch
User's Guide
Acer Switch
ALW-3016
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– 1
I
Copyright
Copyright©1998-1999 Acer Netxus Inc. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of Acer
Netxus Inc.
Disclaimer
Acer Netxus Inc. makes no representations or warranties, either expressed
or implied, with respect to the contents hereof and specifically disclaims
any warranties, merchantability or fitness for any particular purpose. Any
software described in this manual is sold or licensed “as is”. Should the
programs prove defective following their purchase, the buyer (and not this
company, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Furthermore, Acer Netxus Inc.
reserves the right to revise this publication and to make changes from time
to time in the contents hereof without obligation to notify any person of
such revision or changes.
Other brand and product names are trademarks and/or registered trademarks of
their respective holders.
User's Manual
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– I
Table of Contents
Chapter 1 Overview
1.1 Product goal.......................................................................1
1.2 Product configuration.........................................................1
Chapter 2 Make your Switch ready
2.1 Installing the switch............................................................2
2.2 Connecting to the power supply.........................................3
2.3 Rack mounting...................................................................4
2.4 Connecting to computers...................................................5
2.5 LEDs interface overview.....................................................5
Chapter 3 Apply a feasible networking
3.1 Connecting a hub/switch to normal port.............................7
3.2 How to use uplink port........................................................8
3.3 Application..........................................................................8
Chapter4 Trouble shooting................................................ 9
Appendix: Specification.......................................................10
II
User's Manual
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– II
Thanks for your purchase of the AcerSwitch 3016. AcerSwitch is an 16-
port dual speed switch works as backbone switch in SOHO environment
for connecting the server or heavy-load user or hubs in LAN environment.
1.1 Product goal
AcerSwitch ALW-3016 provides high-speed and easy access to the LAN
and Intranet for corporations. It allows data transmission at speeds of 10
Mbps or 100 Mbps. It provides an easy installation, all you have to do is
plug the cables from the adapter cards or hub port to the ports, check the
LEDs and you can start networking. And AcerSwitch also provides some
advanced features only provided in some corporate products such as FAN
error. Advise you in advance to prevent the down of LAN or damage of the
equipment.
1.2 Product configuration
The product configuration inside the package is shown in the figure 1-2-1.
Please check the contents of the package if there is any missing part
before using the switch. The accessories of this product include:
Figure 1-2-1 Product configuration of ALW-3016
1. Overview
1
User's Manual
1. ALW-3016 dual speed switch
3. Power Code 4. Mounting Brackets and Screws
5. Rubber Footpads
2. User Manual
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– 1
This chapter will guide you through how to install the AcerSwitch ALW-
3016. It includes procedures for connecting to the external power supply,
installing the switch on your working surface, connecting the switch to your
computer, and guidelines to see if it works well. Before setting up your
switch, please take notes of the front and rear panel of this switch, as
shown in Figure 2-1 and 2-2.
Figure 2-1 Front panel
Figure 2-2 Rear Panel
2.1 Installing the switch
You have to find a solid working surface to place the switch and make sure
the equipment is not close to any high voltage power source or over-
heated sources. Also keep away from electronic equipment sensitive to
electronic interface. The brief procedures of installing your switch should be:
2. Make Your Switch Ready
User's Manual
2
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– 2
2.2 Connecting to the power supply
Carefully unpack the AcerSwitch ALW-3016 and it's accessories. For the
first time that you use this switch, please make sure there is all the same
as the checking list in the package. The procedure for connecting to the
power will be:
1. Place the switch on the desktop and remove the packing box of the
power adapter.
2. Please stretch and plug the cord into the power jack of the switch.
3. Check if the PWR LED lights up. If it lights up, then the switch is ready
to be connected to the network. See Figure 2-2-1.
Figure 2-2-1 Connecting to the power
3
User's Manual
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– 3
2.3 Rack mounting
To install the ALW-3016 switch in a 19-inch rack, please follow these steps:
1. If the switch has rubber footpads on the bottom of the unit, please
remove them.
2. Locate the rack mounting holes on both sides of the switch (see Figure
2- 3).
3. Using a cross-head screwdriver, attach the two mounting brackets to
both sides of the switch with the four screws supplied with the unit (see
Figure 2- 3).
4. Place the switch in the rack and align the holes in the mounting bracket
with the holes in the rack chassis (see Figure 2- 4).
5. Insert two mounting screws (the rack-mount equipment should provide
these screws), into each of the mounting brackets and tighten with a
suitable screwdriver.
Figure 2-3: Attaching mounting brackets (8 screws: M3x5)
Figure 2-4: Attaching mounting brackets for a rack mount (4 screws: M5x10)
Note: The pannel wall should be able to bear three times of the system's
weight
4
User's Manual
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– 4
2.4 Connecting to computers
Make sure the switch is ready for networking by checking if the PWR
indicator displays.
1. Shut down the computer and install an adapter card in.
2. Plug in the one end of UTP cables to the RJ-45 phone jack of adapter.
3. Plug the other end of UTP to normal ports of the switch.
4. Turn on the PC and check if the Link LEDs on the adapter card and the
switch (Named as LNK ACT 100/LNK ACT 10) are lit up. See Figure 2-4-1
If the LED is not lit up, there must be something wrong and please
reference to Chapter 4 for quick trouble shooting.
Figure 2-4-1 Connecting to computers
2.5 LEDs interface overview
You can observe the LEDs status to see if the hub works fine. The
meanings of LEDs are summarized as Table 2-5-1.
5
User's Manual
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– 5
Table 2-5-1 LEDs definition
2.5.1 System indicators
PWR: When the power is connected rightly, the PWR LED will be lit on
Green. If the LED is not lit on, then you should check the connection of
your power and the outlet of power.
Fan Err.: When the fan malfunction at work, then the Fan Err LED will be
lit up and blink. And when the fan is fail, the LED will be lit without blinking.
You should check you fan and your vender and have a new fan to instead
of the old one to make sure the equipment will work normally.
Note: There are two Fan inside the ALW-3016. Fan Err1 & Fan Err2 indicate the two
Fans individually.
2.5.2 Port indicators
LNK ACT 100/LNK ACT 10: When the port is linked with 100Mbps device,
the LNK ACT 100/LNK ACT 10 will be lit on GREEN, or it will be lit on
orange with 10Mbps device.And when there's any transmission activity in
the port, the LED will be blinking in GREEN with 100Mbps or in orange
with 10Mbps. If the port is linked, and the LED isn't lit up, please check if
the port connector fasten tightly.
FDX: When the port is connected with full duplex, it will be lit up on
GREEN. Others it will be DARK.
6
User's Manual
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– 6
This chapter describes the network topology for hybrid 10 Mbps and 100
Mbps networks, cabling requirement for connections, the interoperability
between hubs and switches. And tell you how to use the ALW-3016 to
expand your port numbers.
3.1 Connecting a hub/switch to normal port
You can use the ALW-3016 as a backbone switch in small and medium
size LAN environment, and for the purpose of expanding your port number
you can connect another hub/switch with it's uplink port to the normal port
of ALW-3016. See Figure 3-1-1
1. Place the hub/switch on a stable surface.
2. Use one end of the UTP/STP cord to connect to the uplink port of the
hub/switch.
3. Use the other end of the UTP/STP cord to connect to the normal port of
ALW-3016
4. Check the status of LNK ACT 100/LNK ACT 10 LED. If the LNK ACT
100 /LNK ACT 10 LED is lit on green then it works normal.
5. Then you can connect the terminal to the new hub/switch
Figure 3-1-1 Connecting to normal port with other hub/switch
3. Apply a feasible networking
7
User's Manual
ALW-3016
ALH-324D
new ALW-3016-UM 10/13/99 11:27 AM ›¶›– 7
Indice
Altri manuali Acer Interruttore
