ACME LS-1005 Manuale utente

LS-1005 RGB

1. Safety Instructions ........................................................................................................................... 2

2. Technical Specifications ................................................................................................................... 3

3. Installation ....................................................................................................................................... 3

4. How to Set the Unit ......................................................................................................................... 4

4.1 Control Panel ................................................................................................................................. 4

4.2 Main Function................................................................................................................................ 4

5. How to Control the Unit .................................................................................................................. 6

6. DMX512 Configuration .................................................................................................................... 6

7. DMX512 Connections ...................................................................................................................... 8

8. Troubleshooting............................................................................................................................... 9

9. Fixture Cleaning ............................................................................................................................. 10

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces.

Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by

taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than

this.

Unit surface temperature may reach up to 65℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing

or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact

the nearest authorized technical assistance center. Always use the same type spare parts.

Please read carefully the instruction, which includes important

information about the installation, usage and maintenance.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

2. Technical Specifications

Four control modes: ILDA / DMX/Sound Active/Auto Play;

Voltage: AC100V~240V，50/60Hz

Laser power consumption: 5W

Power consumption: 80W

Scanning system：40K Scanner

Scanning angle: ±40°

Fuse: T 3.15A

Dimension/Weight:

373X370X193mm, 12.5Kg

14.7"x14.6"x7.6"in, 27.6lbs

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

4. How to Set the Unit

4.1 Control Panel

○

1OLED Display ○

2Knob

○

3 SD Card Port ○

4 Key Switch: The unit works when set RUN.

○

5 Power Input/output ○

6 Fuse

○

7 MIC ○

8 ILDA Port

○

9 DMX Input/Output ○

10 Power Indicator (Red); Laser Indicator (Green)

○

11 Light Output

4.2 Main Function

Turn the knob PUSH/DIAL, select any of the given functions, press the knob until the required function is

showing on the display. The main functions are shown overleaf:

DMX Functions

Press the knob when the DMX FUNCTIONS show on the display, use the knob to select DMX Address,

DMX state or Exit. Enter DMX Address, turn the knob to change the address, press the knob to confirm.

Enter DMX State, select the HOLD/Black Out/Show Mode, when select Show Mode, the unit preference

to sound active. If the sound active function is closed, the unit will auto run built-in show. ILDA signal

control prior to DMX signal control. Press EXIT to back to the menu.

Show Functions

Press the knob when the Show Functions show on the display, use the knob to select Show or Exit. Enter

Show, turn the knob to select show 0 to show 9, press the knob to confirm. (Show function only is valid

when select Show Mode in DMX functions.) SD card show prior to built-in show. Press EXIT to back to

the menu.

Sound Functions

Press the knob when the Sound Functions show on the display, use the knob to select Sound Mode or

Sound Sense or Exit. Enter Sound Mode, use the knob to select On or off, press the knob to confirm.

ILDA signal and DMX signal control prior to sound active mode. Press EXIT to back to the menu.

SD Functions

Press the knob when the SD Functions show on the display, use the knob to select SD Mode, SD File or

Exit. Enter SD Mode, use the knob to select ILD Show, PRG Show or No SD, press the knob to confirm.

Enter SD File, select the file or folder, press the knob to confirm. Press EXIT to back to the menu.

Figure Functions

Press the knob when the Figure Functions show on the display, use the knob to select Size, Phase Set or

Exit. Enter Size, use the knob to select figure size from 10 to 100, press the knob to confirm. Enter Phase

Set, set the positon of the figure. Press EXIT to back to the menu.

Fixture Functions

Press the knob when the Fixture Functions show on the display, use the knob to select Back Lights,

Fixture Hours, Defaults, Version or Exit. Enter Back lights, use the knob to select on or off, press the

knob to confirm. Enter Fixture Hours, the running time of the unit will be show on the display. Enter

Defaults, use the knob to select Yes or no to restore factory settings or not. Enter Version, the version of

the software will be show on the display. Press EXIT to back to the menu.

5. How to Control the Unit

1. By ILDA;

Connect the unit to the computer with ILDA wire and control the software by computer laser;

Priority to control the unit: ILDA﹥DMX﹥Sound active﹥Auto play

2. By universal DMX controller;

Set the DMX address, the unit will be ready to receive DMX signal.

3. Sound active;

The unit will run show by the sound active.

4. Auto play;

The unit will auto play when no signal.

6. DMX512 Configuration

DMX Channel:

Channel

Value

Function

Choose

Mode

0-9

Blackout

10-49

PRG Mode

50-99

ILD Mode

100-149

Sound active Mode

150-199

Auto play Mode

200-255

Manual Mode

Pattern/File

Select

0-255

Manual Mode

PRG/ILD Mode

Pattern change

(Change pattern every

3 values)

Select file

Strobe/File

Select

0-10

No strobe

Auto Play File Select

11-255

Auto strobe

Pan Moving

0-125

Position select

126-155

Repeat moving from left to right

156-185

Repeat moving from right to left

186-225

Repeat moving from left to right

226-245

Auto play

246-255

Sound active play

Tilt Moving

0-125

Position select

126-155

Repeat moving from left to right

156-185

Repeat moving from right to left

186-225

Repeat moving from left to right

226-245

Auto play

246-255

Sound active play

Zoom

0-10

No effect

11-87

Manual adjust

188-150

Zoom in

151-200

Zoom out

201-255

Repeat zooming

Pan

Rotation

No rotation

1-128

Manual adjust

129-255

Auto rotation

Tilt

Rotation

No rotation

1-128

Manual adjust

129-255

Auto rotation

Centre

Rotation

No rotation

1-128

Manual adjust

129-192

Counter-clockwise rotation

193-255

Clockwise rotation

Slow

Drawing

0-11

No function

12-74

Manual adjust

75-104

Auto slow drawing from slow to fast

105-144

Auto slow drawing from fast to slow

145-184

Repeat slow drawing

185-224

Repeat slow drawing from slow to fast end to end

225-255

Repeat slow drawing from fast to slow end to end

Pan Waving

0-10

No function

11-69

Small wave

70-129

Middle wave

130-189

Big wave

190-255

The biggest wave

Tilt Waving

0-10

No function

11-69

Small wave

70-129

Middle wave

130-189

Big wave

190-255

The biggest wave

Show Mode

0-63

Normal Show Mode

64-127

Light spot Show Mode

128-191

Division Show Mode

192-255

Spot Show Mode

Color

RGB

0-16

White

17-33

Red

34-50

Green

51-67

Blue

68-84

Yellow

85-101

Purple

102-118

Cyan

119-135

White/Red/Green/Blue division

136-152

Blue/Yellow/Purple/Cyan division

153-169

White/Red/Green/Blue/Yellow/Purple/Cyan

division

170-186

White/Red/Green/Blue flow

187-203

Blue/Yellow/Purple/Cyan flow

204-220

White/Red/Green/Blue/Yellow/Purple/Cyan

flow

221-237

Division show according to the breakpoint

238-255

Sound active change color

Dimmer

0-5

Full light

6-255

Bright to dim

Dimmer

0-5

Full light

6-255

Bright to dim

Dimmer

0-5

Full light

6-255

Bright to dim

7. DMX512 Connections

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable.

2. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the input of

the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a very high-speed signal.

Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal

and shut down the system.

3. The DMX output and input connectors are pass-through to maintain the DMX circuit, when one of

the units’ power is disconnected.

4. Each lighting unit needs to have an address set to receive the data sent by the controller. The

address number is between 0-511 (usually 0 & 1 are equal to 1).

5. The end of the DMX 512 system should be terminated to reduce signal errors.

6. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin 4/Pin 5: Not used.

8. Troubleshooting

Following are a few common problems that may occur during operation. Here are some suggestions

for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

Indice

Altri manuali ACME Attrezzatura di illuminazione

ACME

ACME Stage Par 220MP-220 Manuale utente

ACME

ACME XP-280 BS Manuale utente

ACME

ACME LED-0408 Manuale utente

ACME

ACME iSolution Manuale utente

ACME

ACME XP-5000SZ F Manuale utente

ACME

ACME MP-12FC Manuale utente

ACME

ACME Solaris Manuale utente

ACME

ACME LIGHT PANEL 1000 Manuale utente

ACME

ACME XP-280 BS Manuale utente

ACME

ACME STAGE PAR 100 COLOUR IP Manuale utente

ACME

ACME SABER HYBRID PRO Manuale utente

ACME

ACME FESTIVAL Manuale utente

ACME

ACME Neozone Manuale utente

ACME

ACME TV LIGHT PANEL 2000 Manuale utente

ACME

ACME Theatre Spot 150m Manuale utente

ACME

ACME Warrior Scan 50 LED-SC50C Manuale utente

ACME

ACME PIXEL LINE IP Manuale utente

ACME

ACME V Inground VI-10QW Manuale utente

ACME

ACME ANIMA C Manuale utente

ACME

ACME Pageant CM-200Z Manuale utente

ACME

ACME Uploader II Manuale utente

ACME

ACME VOGUE Manuale utente

ACME

ACME BIG BANG Manuale utente

ACME

ACME Ozone 3 Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente