ACTi SED-3300 Manuale utente
Video Transcoder
SED-3300
Ver.061031
Q
uick Installation Guide
1-1
1 Getting Started
1.1 PACKAGE CONTENTS
SED-3300 WarrantyCard
Product CD Terminal Blocks & Screws
Power Adaptor (Option)
1
1-2
1.2 PHYSICAL DESCRIPTION
Read the following information to familiarize yourself with the video transcoder, and
make particular notes of where the connectors and LEDs are located.
Front Panel
1. Red LED
LED Indicating Power or H/W Reset Function
2. Yellow LED
LED Indicating when RS-485 Rx is active
3. Green LED
LED Indicating when RS-485 Tx is active
4. Reset Button
Get back to default value while forgetting Login Name & Password
Procedure
1. Switch off the video transcoder by disconnecting the power cable
2. Using a suitable pointed object, press and continue to hold the Reset Button
depressed. While continuing to hold the Reset Button depressed, reconnect
the power cable.
3. Keep holding the Reset Button depressed around 6 seconds, release the
Reset Button. The unit will start up with the factory default settings.
1-3
5. Terminal Blocks Pin 1~6
PIN NAME DESCRIPTION
1 DO1 Digital Output 1
2 DO2 Digital Output 2
3 GND Ground Pin
4 DI1 Digital Input 1
5 DI2 Digital Input 2
6 GND Ground Pin
6. Terminal Blocks Pin 7~12
Pin 7~10: RS232/422/485. Default mode is RS-485 (if your system needs RS-232 or RS-422,
please contact our sales)
DESCRIPTION
PIN NAME
RS-485 RS-422 RS-232
7 Tx+ D+ Tx+ Tx
8 Tx- D- Tx-
9 Rx+ Rx+ Rx
10 Rx- Rx-
11 12V Power Input (DC +12V)
12 GND Ground Pin of Power Input &
RS-232
7. LAN Port
10/100 Mbps auto-sensing, fast Ethernet port of secure LAN.
8. WAN Port
10/100 Mbps auto-sensing, fast Ethernet port of WAN for FTTH or xDSL connectivity
1-4
Rare Panel
1 Dip Switch or Serial Port
RS-485 or RS-422 pin degine (default is RS-485)
RS-232 pin define
2 Y/C
Analog Video Output of Y/C Signal with S-Video Connector
3 Composite
Analog Video Output of Composite Signal with BNC Connector
1-1
1.3 CONNECT NECESSARY CABLES
Follow the procedures below to connect the video transcoder to the respective apparatuses.
1. The IP camera or other encoding devices as a video source
2. The video server or other encoding devices as a video source
3. Connect video server / IP camera and video transcoder to an Ethernet hub (RJ45 connectors)
4. Video transcoder is the receiver side
5. Connect a coaxial cable to TV monitor and display the video which encoded and transferred from
video server / IP camera
2-2
2 Quick Tour
This section guides you with a quick tour on our video transcoder.
2.1 Configure the video transcoder
2.1.1 Make sure network environment
Default IP of video transcoder is 192.168.0.200. Please make sure the video
transcoder and your PC are on the same network segment before running the
installation.
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 200 is
excepted.)
2-3
2.1.2 Open Internet Explorer with IP address
This section describes how to configure the video transcoder. The product administrator has
unlimited access to all setup windows and normal users can only watch the live images. The video
transcoder is configured under a standard browser (Microsoft Internet Explorer 6.0 or above).
Follow the procedures below to configure the video transcoder.
zSTEP1: Open a browser
zSTEP2: Enter the IP address of the video transcoder.
The default IP address is “192.168.0.200”
zSTEP3: Enter the Account name (factory default: Admin) and the Password (factory
default: 123456).
zSTEP4: Select the language of the video transcoder user interface. You can select
from English, Traditional Chinese, Simplified Chinese, Japanese and Spanish.
zSTEP5: Click the button to login or click the button to re-enter
again.
2-4
2.1.3 Set a new IP address
*Host Name : Enter a domain name. The default Host Name is ACTi.
*Language : Language setting for Web Configurator. The default setting is English.
*IP Address : The IP address of the LAN interface. The default IP address is 192.168.0.200.
*Subnet Mask : The subnet mask of the LAN interface.The default subnet mask is 255.255.255.0
*Click button
2-5
2.1.4 Select a video server / IP camera
This section tells you how to setup video server or IP camera’s video and streaming
settings.
*Protocal Version Select : Select protocol version 1.0 or protocol version 2.0
*Patrol Channel Select : Select channel number to be patrolled
*Connect Type : Select Multicast or TCP mode for connecting to a video server/IP camera.
*TCP Connect IP : Set IP address of a video server / IP camera while Connect Type is TCP
Streaming.
Indice
