ACTi ACM-8511 Guida rapida
www.acti.com
ACTi
Knowledge Base
Category: Installation & Configuration Note
Sub-category: Streaming & Networking; Preview; Integration; Application
Model: ACM-8511,ACM-82X1
Firmware: N/A
Software: N/A
Author: Athena.Tsai
Published: 2010/04/07
Reviewed: 2010/06/25
1
How to Configure PTZ Functions
Contents
Introduction
Functions of PTZ camera
。Manually PTZ
。Preset points
。Auto scan
。Preset tour
Introduction
PTZ (pan, tilt, and zoom) cameras are devices that can be moved left and right (pan), up and
down (tilt), and zoom in and out.Why do we need PTZ camera? There are several advantages
of PTZ camera.
First of all, it can be remotely controlled to pan, tilt and zoom.Wherever you are, you can easily
adjust the camera toward the area you want to monitor without going to the site where the
camera is. Furthermore, the preset functions allows you to monitor multiple areas as long as
the camera can point to the right direction. This function greatly increases the flexibility of your
video surveillance system.
You also can set schedules for the PTZ camera to monitor several different areas in turn. For
example, you may want to monitor the whole area in the day time, but just the entrance during
the night as no one should show up there. You just need to make preset points for these two
different areas and make a tour to let your camera move between them.
In the following chapter, we are going to show you how to configure PTZ functions including
manual PTZ, preset points, auto scan, and preset tour.
www.acti.com
2
Functions of PTZ Camera
Manual PTZ
You can use PTZ control panel to remotely control the camera.
a. Via web configurator
Click ‘PTZ’. The PTZ control panel will pop up. You can use it to pan, tilt, and
zoom in and out.Besides those, you also can control the speed of panning tilting,
and zooming.
www.acti.com
3
b. Via NVR
First, you have to enable PTZ function and choose the correct model and
protocol. Press apply and restart ActiveSetup.
Open ActiveMonitor. You will be able to use the control panel on the left side to
control the camera to pan, tilt, and zoom.
www.acti.com
4
Preset points
You may have many places to monitor for your PTZ camera. You can use this
function to let your camera switch between the preset areas. Then you can go to
these preset points by scheduled time or by certain events.
For example, if you want to monitor the platform of a train station, you may want to
see not only the whole area, but also some cetain spots for different needs.Then you
can schedule an event and make the camera to monitor the platform during the day
time and move to another certain spot during the night time. (Note: If you need to
know how to schedule or configure a event, please reference the document
http://www.acti.com/support/KnowledgeBase/outside/detail.asp?KB_ID=KB20100125001.)
Now, you have to know how to set preset points and you will know how to make a
tour for preset points in the last section.
a. Via web configurator
First, you have to use PTZ control panel to adjust the camera and aim at the
area you want to monitor.
After completing the adjustment, click ‘Preset’button to go to the preset page.
You can choose any number and then click the corresponding ‘Set’button. You
www.acti.com
5
also have to set up the name. After that, you’ve done all the settings of one
preset point. If you need to set up another preset point, please repeat the steps
from the last step to this one.
After all the settings are done, go back to PTZ page.You will be able to use these
preset points by clicking the number ID and shift your view to that preset point.
www.acti.com
6
b. Via NVR
1. Go to ActiveSetup / PTZ Preset.
2. Click ‘Live View’to get the real time video
3. Use ‘PTZ Operation’to adjust the camera
4. Choose the number and enter the name you want. Click the Check mark to
remember it.This will setup the PTZ preset point.
Go back to Active Monitor, and you will see the entry you set is in the ‘Goto’check list.
Afterward, you can use it and go to the preset points easily.
www.acti.com
7
Auto Scan
If the function auto scan is enabled, the camera would pan left to right continuously
to scan the whole area.
a. Via web configurator
The auto scan control is under PTZ -> Other Controls. You also can set the
speed for auto scan.
b. Via NVR
Choose ‘Start Scan’, then it will start to scan.
Note:We suggest you avoid continuous auto scan unless really needed, and use preset points
instead.The reason of it is that the non-stop movement puts a lot of stress on the it may reduce
the life of your PTZ camera. It’s like if you keep running a machine (ex: a car is driven
continuously for a long time), the machinery part would possibly wear away sooner than if you
give it some rest in between activities.
www.acti.com
8
Preset Tour
You can assign several preset points, and link them in a tour to monitor each area for
the duration you want. For example, in the warehouse, you would want to both see
the overview and focus on a certain production line. Therefore, you have to set
thoses areas as preset points. And then you can make them a tour and set the time
to patrol them. The camera will then monitor different areas according to your
assigned schedule. If you set four preset points for the tour, it will go from number
one to four, and go back to number one and run to four, over and over again. Tours
can be triggered by event or run on scheduled time. Please reference the document
(http://www.acti.com/support/KnowledgeBase/outside/detail.asp?KB_ID=KB201001
25001) for how to configure an event.
a. Via web configurator
1. Set the preset points that you want to monitor
2. (1)Choose a tour
(2)Click Edit
www.acti.com
9
3. Make a tour by configuring the sequence of the preset points and the time.
(1) Choose one preset point
(2) Set the time interval that you want camera to moniter the area
(3) Click add(+) button
(4) When you finish setting, don’t forget to save it
4. If you need to adjust the sequence, you can use the buttons as below.
www.acti.com
10
b. Via NVR
(1) Set the preset points. Then you can see the setting in ActiveSetup and
ActiveMonitor
Figure: (left) ActiveSetup; (right)ActiveMonitor
(2) Go to ActiveSetup and Preset Tour page. Secondly, set the tour name and
click ‘Apply.’Then you can see the entry you set in the tour list.
Altri manuali per ACM-8511
2
Questo manuale è adatto per i seguenti modelli
1
Altri manuali ACTi Telecamera di sicurezza
ACTi
ACTi B412 Manuale utente
ACTi
ACTi A711 Manuale utente
ACTi
ACTi TCM-1231 Series Istruzioni per l’uso
ACTi
ACTi Q115 Manuale utente
ACTi
ACTi B57A Manuale utente
ACTi
ACTi TCM-5311 Guida rapida
ACTi
ACTi ACM-7411 Series Manuale utente
ACTi
ACTi B4 Series Manuale utente
ACTi
ACTi VMGB-200 Manuale utente
ACTi
ACTi ACM-3001 Istruzioni per l’uso
ACTi
ACTi D41A Manuale utente
ACTi
ACTi ACM-1100 Series Manuale utente
ACTi
ACTi KCM-5111 Manuale utente
ACTi
ACTi B21 Manuale utente
ACTi
ACTi I93 Manuale utente
ACTi
ACTi ACM-7411 Series Manuale utente
ACTi
ACTi I91 Manuale utente
ACTi
ACTi D21 Manuale utente
ACTi
ACTi VMGB-351 Manuale utente
ACTi
ACTi ACM-360 Series Istruzioni per l’uso
