ACTi CAM-6200 Manuale utente

IP Speed Dome

Quick Installation Guide

Ver. 061031

Model: CAM-6200/6220

0-1

0PRECAUTIONS

1. Read these instructions

All the safety and operating instructions should be read before the product is

operated.

2. Heed all warnings

All warnings on the product and in the instruction manual should be adhered to.

The symbol indicates the following items, please carefully read the

description next to each symbol.

a. Failure to follow the safety instruction given may directly endanger

people, cause damage to the system or to other equipment.

b. The requirements to make this device work, including hardware,

computer settings, network settings, and operation procedures.

c. The tips to make using this device easier, more convenient and more

efficient.

3. Servicing

Do not attempt to service this video product yourself as opening or removing

covers may expose you to dangerous voltage or other hazards. Refer all servicing

to qualified service personnel.

This manual is the intellectual property of ACTi and is protected by copyright. All

rights are reserved. No part of this document maybe reproduced or transmitted for any

purpose by any means including electronic or mechanical without the official written

permission from ACTi.

Trademarks

All names used in this manual for hardware and software are probably registered

trademarks of respective companies.

Liability

Every care has been taken during writing this manual. Please inform your local office

if you find any inaccuracies or omissions. We cannot be held responsible for any

typographical or technical errors and reserve the right to make changes to the product

0-2

and manuals without prior notice.

FCC/CE Regulation

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

FCC Caution: To assure continued compliance, (example –use only shielded

interface cables when connecting to computer or peripheral devices). Any changes or

modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

CE: This device passed the test performed according to the European standard

EN55022:1998 Class A, EN 61000-3-2:2000, EN61000-3-3”1995/A1:2001,

EN55024:1998/A1:2001.

0-3

Table of Contents

0PRECAUTIONS................................................................................................ 0-1

Copyright .....................................................................................................................................0-1

Trademarks ..................................................................................................................................0-1

Liability........................................................................................................................................0-1

FCC/CE Regulation .....................................................................................................................0-2

1Installation ........................................................................................................ 1-1

1.1 Connections .........................................................................................................1-1

1.1.1 Indoor connections ........................................................................................................1-1

1.1.2 Outdoor connections......................................................................................................1-2

1.2 Speed dome setup................................................................................................1-3

1.2.1 Setup camera ID, baud rate and protocol.......................................................................1-3

1.3 Indoor installation...............................................................................................1-5

1.3.1 Punching a hole in the ceiling........................................................................................1-5

1.3.2 Take out the camera.......................................................................................................1-5

1.3.3 Fit the upper casing into the ceiling as shown below. ...................................................1-5

1.3.4 Screw the screws securely to ensure the camera is tightly locked to the ceiling. ..........1-5

1.3.5 Once complete the above steps, place the complete camera (except the dome cover)

back to the ceiling as shown below..............................................................................................1-6

1.4 Outdoor H/W installation procedures...............................................................1-7

1.4.1 Understand Outdoor applications ..................................................................................1-7

1.4.2 Install the mount ............................................................................................................1-9

2Configuration.................................................................................................. 2-10

2.1 Network video platform (Web configurator) setup .......................................2-10

2.1.1 Make sure network environment .................................................................................2-10

2.1.2 Open Internet Explorer with IP address.......................................................................2-11

2.1.3 Login with default administrator’s account & password .............................................2-11

2.1.4 Preview the video ........................................................................................................2-12

2.1.5 Set the new IP address .................................................................................................2-13

2.1.6 Check default video setting .........................................................................................2-14

2.1.7 Click Save Reboot to restore all settings and please wait about 30 seconds for system

reboot. .....................................................................................................................................2-14

0-4

2.2 AP (Streaming Activator) setup.......................................................................2-15

2.2.1 Open Streaming Activator...........................................................................................2-15

2.2.2 Click Setup. .................................................................................................................2-15

2.2.3 Click PTZ setup...........................................................................................................2-16

2.2.4 Click PTZ setup and follow the picture below to setup...............................................2-17

2.2.5 Press the Apply button and reconnect to the IP speed dome. ......................................2-17

2.2.6 PTZ function will work perfectly now.........................................................................2-17

3Appendix.......................................................................................................... 3-18

3.1 Camera ID setup ...............................................................................................3-18

1-1

1Installation

1.1 Connections

Indoor IP speed dome connection is different from the outdoor IP speed

dome. Follow the description below to connect to respective apparatus.

1.1.1 Indoor connections

1. Analog Video-out connector

Connect it to the video-in port of respective apparatus. The signal is 75Ω

Composite Video Signal.

2. DC jack-in for power input

Connect this DC jack to the power supply of 12VDC, 1.0A input.

3. LAN port

The video server connects to the LAN (local area network) via a standard

RJ45 connector. Supporting NWAY, this video server can auto detect the

speed of local network segment (10Base-T/100Base-TX Ethernet).

4. WAN port

The video server connects to the WAN (wide area network) via a standard

RJ45 connector. Supporting NWAY, this video server can auto detect the

1-2

speed of local network segment (10Base-T/100Base-TX Ethernet). The

WAN port is for FTTH and connects to an xDSL or cable modem.

1.1.2 Outdoor connections

1. Analog Video-out connector

Connect it to the video-in port of respective apparatus. The signal is 75Ω

Composite Video Signal.

2. Power input

Connect this DC jack to the power supply of 110VAC or 230VAC

according to the product you bought.

3. LAN port

The video server connects to the LAN (local area network) via a standard

RJ45 connector. Supporting NWAY, this video server can auto detect the

speed of local network segment (10Base-T/100Base-TX `Ethernet).

4. WAN port

The video server connects to the WAN (wide area network) via a standard

RJ45 connector. Supporting NWAY, this video server can auto detect the

speed of local network segment (10Base-T/100Base-TX Ethernet). The

WAN port is for FTTH and connects to an xDSL or cable modem.

1-3

1.2 Speed dome setup

Follow the description below setup IP speed dome’s hardware camera ID,

baud rate and protocol.

Speed dome setup Video platform setup

AP (Streaming

Activator) setup

Camera ID, baud rate and protocol setting in these 3 item should be the same

for PTZ control function to work.

1.2.1 Setup camera ID, baud rate and protocol

Loosen the four screws and de-attached the dome cover from the housing.

Follow the tables below to setup each respective parameter.

Address ID Protocol/

Baud Rate

1 2 3 4 5 6 7 8 9 10

Setting of camera ID Address and

Communication Protocol

1-4

zProtocol and baud rate switch

SW9 SW10

PELCO D-2400 OFF OFF

PELCO P-4800 ON OFF

PELCO P-9600

(Recommended)

OFF ON

EYEVIEW ON ON

zCamera ID address setting

Please refer to the Appendix. A “Camera hardware ID setup”

1-5

1.3 Indoor installation

1.3.1 Punching a hole in the ceiling

Remove the target ceiling first, then attach the hole-sticker supplied with

the camera to the ceiling and make the desired hole accordingly with a

proper tool.

1.3.2 Take out the camera

1.3.3 Fit the upper casing into the ceiling as shown below.

1.3.4 Screw the screws securely to ensure the camera is

tightly locked to the ceiling.

Please check carefully, otherwise the camera might fall to cause harm to

itself or other person or properties.

Altri manuali per CAM-6200

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente