ADA INSTRUMENTS COSMO 150 VIDEO Manuale utente
Laser distance meter
OPERATING MANUAL
COSMO 150
VIDEO
adainstruments.com
2English
THE MANUFACTURE RESERVES THE RIGHT TO MAKE CHANGES (NOT HAVING AN IMPACT ON THE
SPECIFICATIONS) TO THE DESIGN, COMPLETE SET WITHOUT GIVING PRIOR WARNING.
PERMITTED USE
• Measuring distances
• Computing functions, e.g. areas, volumes, subtractions, trapezoid, Pythagorean calculation, mea-
surements with the tilt sensor.
SAFETY INSTRUCTION
The safety regulations and instructions along with the operating manual should be read carefully
before initial operation.The person responsible for the instrument must ensure that equipment
is used in accordance with the instructions. This person is also accountable for the deployment of
personnel and for their training and for the safety of the equipment when in use.
3
English
• Please follow up instructions given in operating manual.
• Do not use instrument in explosive environment (lling station, gas equipment, chemical produc-
tion and so on).
• Do not remove warning labels or safety instructions.
• Do not open instrument housing, do not change it’s construction or modication.
• Do not stare at beam. Laser beam can lead to eye injury (even from greater distances).
• Do not aim laser beam at persons or animals.
• Opening of the equipment by using tools (screwdrivers, etc.), as far as not specically permitted for
certain cases.
• Inadequate safety precautions at the surveying site (e.g. when measuring on the roads, construc-
tion sites and so on).
• Use the instrument in the places where it could be dangerous: on the air transport, near manufac-
turers, production facilities, in the places where the work of laser distance meter can lead to the
harmful eects on people or animals.
4English
START UP
KEYPAD
1. ON/Measuring
2. Digital Camera Button
3. Addition
4. Area/Volume
5. Reference/Time
6. Angle/Stake out function
7. Clear/OFF
8. Indirect measurements
9. Substraction
10. Trapezoid
11. Menu/Equal Button
1
11
2
10
39
5
4
8
6
7
5
English
DISPLAY
The graphics screen of the measurement window is
split into dierent areas. The selected measuring func-
tion is shown at the left top part. The 1-It measurement
eld contains the previous measurement results. There
are 5 rows on the display.
1. Current measurement function
2. Indicator of laser point
3. Indicator of selected reference point
4. Digital level
5. Indicator of Bluetooth
6. Battery power
7. Previous measurement
8. Result of previous measurement
9. Current measurement function and result
6English
1
2
3
4
1. Current measurement function.
2. Results of successive measurements
3. Additional calculations
4. Main result
7
English
DISPLAY IN DIGITAL CAMERA MODE
Built-in digital camera shows the target directly on the
display. The instrument takes measurements with the
help of crosshairs, even if the laser dot is not visible (in
bright illumination).
When the digital camera is used for close targets
(<10m) the laser dot may not coincide with the image in
the center of the display. In this case you should rely on
the actual laser dot for targeting the object.
8English
INSERTING / REPLACING BATTERIES
Remove battery compartment cover. Insert new batteries in it. Obsurve the polarity. Close the battery
cover. Replace the batteries if the power level is very low. Remove the batteries, If the device will not be
used for a long time. Use alkaline batteries. To use the battery, install it in the place of the battery cover.
NOTE: Charge the battery using a charger with an output voltage of 5 V or less. Do not leave the
charger and battery unattended.
NOTE: We reccomend to use LI /IRON Batteries (energy-plus battery).
Approximate time of continious operation*:
• LI / IRON (4 000 mAh) - about 5 hours
• NiMh (2 000 mAh) - about 3.5 hours
*in condition of operation under environment temperature 20°C and also average values of instrument settings
(brightness, contrast and so on).
END-PIECE
If the end-piece is rotated by 180°, then you need to move the reference point for measurement from the
bottom of the end-piece. Press button (5). Selected reference point is appreared on the display.
9
English
Push the positioning end-piece slightly to the right (90°) to measure from the corner or the edge of the
ob ject.
ADJUSTMENT FUNCTIONS
1. Current measurement (distance)
2. Unit of measurement (corner)
3. Digital level
4. Continious laser
5. Brightness of the display
6. Sound alarm
7. Oset of reference point
8. Calibration of tilt sensor
9. Tripod
10. Factory reset
11. Bluetooth
17
39
28
410
511
6
10 English
Press and hold button to enter into the menu. Press buttons or to change the settings of
submenu. Press and hold menu button to conrm settings.
Press button to exit from the menu without saving.
Setting the unit for distance
measurements
Select in the menu article 1.
MEASUREMENT UNIT (DIS-
TANCE) to change the measure-
ment units. Change units by
pressing buttons or .
Indice
Lingue:
Altri manuali ADA INSTRUMENTS Strumento analitico
ADA INSTRUMENTS
ADA INSTRUMENTS COSMO MINI Manuale utente
ADA INSTRUMENTS
ADA INSTRUMENTS Metrix 60 Manuale utente
ADA INSTRUMENTS
ADA INSTRUMENTS ZVE 150SD Manuale utente
ADA INSTRUMENTS
ADA INSTRUMENTS COSMO 60 GREEN Manuale utente
ADA INSTRUMENTS
ADA INSTRUMENTS ROBOT-60 Manuale utente
ADA INSTRUMENTS
ADA INSTRUMENTS COSMO 120 video Manuale utente
ADA INSTRUMENTS
ADA INSTRUMENTS Cosmo 100 Manuale utente
