Adaptec 29320A Manuale utente
ADAPTEC SCSI CARD 29320A
INSTALLATION GUIDE
ASC-29320A IG.fm Page 0 Tuesday, July 29, 2003 3:30 PM
1
Introduction
The Adaptec SCSI Card 29320A enables you to connect up to 15
Low Voltage Differential (LVD) and/or 15 Single-Ended (SE) SCSI
devices—such as very large arrays of high-performance hard disk
drives, external storage subsystems, Ultra320/160 hard disk drives,
scanners, and CD-ROM drives—to any Intel-based computer with
64- or 32-bit PCI/PCI-X expansion slots.
The Adaptec SCSI Card 29320A has one internal and one external
68-pin LVD connector and two internal SE SCSI connectors (one
68-pin and one 50-pin).
Although the Adaptec SCSI Card 29320A is a 64-bit PCI/PCI-X
card, it also works in a 32-bit PCI slot. When installed in a 32-bit
PCI slot, the card automatically runs in the slower 32-bit mode.
This installation guide explains how to:
■Install the Adaptec SCSI Card 29320A
■Set up SCSI devices
■Connect SCSI devices
68-pininternalLVD
connector 68-pin internal SE
connector
68-pinexternal
LVD connector
50-pin internal SE
connector
ASC-29320A IG.fm Page 1 Tuesday, July 29, 2003 3:30 PM
2
Installing the Adaptec SCSI Card 29320A
1Discharge any static electricity build-up before handling your
SCSI card by touching a grounded metal object (like the
exposed metal parts on the back of your computer).
Warning: Turn OFF power to the computer and disconnect
the power cord.
2After you turn off your computer and unplug the power cord,
remove the cover from the computer.
3Locate an unused 64-bit PCI/PCI-X expansion slot and remove
the expansion slot cover. If the computer does not have a 64-bit
slot, you can install the card in a 32-bit PCI slot. The Adaptec
SCSI Card 29320A supports both 5V and 3.3V 64-bit slots. (The
expansion slot must be compliant with PCI Rev. 2.1 or PCI-X
Rev. 1.0 and must support Bus Mastering.) Save the slot cover
screw for use in Step 4.
Slot cover screw
Expansion slot cover
64-bit PCI slot
32-bitPCI slot
ASC-29320A IG.fm Page 2 Tuesday, July 29, 2003 3:30 PM
3
Computers may have vertical or horizontal expansion slots.
Refer to your computer manual to locate the PCI/PCI-X slots. If
your computer is a tower model, lay it on its side to allow for
easier installation of the Adaptec SCSI Card 29320A.
Warning: Be careful when inserting the Adaptec SCSI Card
29320A in a PCI slot. Some 32-bit slots will not
accommodate it, and the card may break if you force it into
the slot.
4Insert the Adaptec SCSI Card 29320A in the 64-bit (or 32-bit)
PCI or PCI-X expansion slot; press down firmly until the card
clicks into place, then replace the slot cover screw. When
installed properly, the card should appear level with the
expansion slot, as shown below.
Setting Up SCSI Devices
There are several things you may need to do to your SCSI devices
before you connect them to the Adaptec SCSI Card 29320A:
■Check the SCSI IDs
■Set the termination
■Connect the power cables
Since setup can vary from device to device, always refer to the
device’s documentation for specific instructions.
ASC-29320A IG.fm Page 3 Tuesday, July 29, 2003 3:30 PM
4
Following are some guidelines for setting SCSI IDs and termination
on your devices.
Check the SCSI IDs
The Adaptec SCSI Card 29320A and each device you connect to it
must have a unique SCSI ID number ranging from 0 to 15 on each
channel. No two devices on the same SCSI channel can have the
same SCSI ID.
The Adaptec SCSI Card 29320A is preset to ID 7 for each channel
and should not be changed. If you boot from a SCSI hard disk,
make sure the hard disk SCSI ID is set to 0. (Most SCSI hard disks
are preset to SCSI ID 0 at the factory.) The SCSI IDs for internal
devices are usually set with jumpers; SCSI IDs for external devices
are usually set with a switch on the back of the device.
Terminate the Ends
To ensure reliable communication on the SCSI bus, the device at the
end of each cable, or the end of the cable itself, must have a
terminator installed (or enabled). Terminators must be removed, or
termination must be disabled, on devices between the ends of each
cable.
Note: When connecting Ultra320/160 or Ultra2 SCSI devices,
the SCSI bus must be terminated either on the end of the cable
(with a permanent terminator) or with a separate terminating
connector. Ultra SCSI and earlier single-ended devices can
terminate the bus directly from the device. If you use an Ultra
SCSI terminator on an LVD Ultra320/160 and Ultra2 SCSI
bus, the SCSI devices will not operate properly. For this
reason be sure that you have the necessary Ultra320/160 or
Ultra2 cable and terminator before installing the Ultra320/160
SCSI devices.
Connecting SCSI Devices
You can connect a total of 15 LVD and/or 15 SE SCSI devices to the
Adaptec SCSI Card 29320A. Before connecting devices, be sure to
review Setting Up SCSI Devices on page 3.
ASC-29320A IG.fm Page 4 Tuesday, July 29, 2003 3:30 PM
5
Connecting Internal Ultra320/160 and Ultra2 Devices
A special 68-pin internal LVD cable is needed to connect internal
Ultra320/160 or Ultra2 SCSI devices. If your cables are not marked,
you can identify most LVD cables as having twisted pairs of the flat
ribbon cable between the device connectors. Some cables are
laminated so that they lay flat. Internal LVD cables usually have a
terminator built into the end of the cable.
The Adaptec SCSI Card 29320A has one internal 68-pin LVD
connector and two internal SE connectors to which you can connect
internal SCSI devices, as shown in the figure on page 1.
Note: Adaptec recommends that you keep your Ultra320/160
and Ultra2 SCSI devices separate from your Ultra SCSI
devices. This allows the Ultra320/160 and Ultra2 SCSI
devices to transfer data at their maximum speed.
Follow these steps to connect your internal Ultra320/160 and
Ultra2 devices:
1Locate a 68-pin internal LVD SCSI cable, which may have either
twisted wires or flat wires, shown as follows.
Nonterminated end
Terminated end
ASC-29320A IG.fm Page 5 Tuesday, July 29, 2003 3:30 PM
6
2Plug the nonterminated end of the cable(s) to the internal LVD
connector.
3Plug the internal Ultra320/160 and Ultra2 SCSI devices to the
other cable connectors, starting with the connector at the
terminated end of the cable.
Note: Internal Ultra320/160 and Ultra2 SCSI devices come
from the factory with termination disabled and cannot be
changed. Proper termination is provided by the terminator
at the end of the LVD SCSI cable.
4Connect a power cable from your computer’s internal power
supply to each internal SCSI device.
Ultra320/160 or Ultra2
SCSI devices
Built-in terminator on cable
Plug first device to
this connector
ASC-29320A IG.fm Page 6 Tuesday, July 29, 2003 3:30 PM
7
Connecting Wide SCSI Devices
Connect internal Wide SCSI devices to the 68-pin internal SE Wide
SCSI connector. To do this, use a 68-pin Wide SCSI cable like the
one shown in Step 1 below. Follow these steps to connect the
devices:
1Locate a 68-pin internal Wide SCSI cable.
2Plug one end of the cable to the Wide SCSI connector on the
Adaptec SCSI Card 29320A.
3Plug the other end of the cable to a terminated Ultra/Fast Wide
SCSI device.
4If you have other Ultra/Fast Wide SCSI devices, attach them to
the connectors between the two ends of the cable. Be sure these
other devices are unterminated.
5Connect a power cable from your computer’s internal power
supply to each internal device.
Connecting Internal Ultra/Fast Narrow Devices
Connect internal Ultra/Fast Narrow SCSI devices that have
standard 50-pin connectors to the 50-pin internal SE Narrow SCSI
connector. To do this, use a 50-pin internal Ultra Narrow SCSI
cable. Follow these steps to connect the devices:
1Locate a 50-pin internal Ultra Narrow SCSI cable.
ASC-29320A IG.fm Page 7 Tuesday, July 29, 2003 3:30 PM
8
2Plug one end of the cable to the 50-pin internal SE Narrow SCSI
connector on the Adaptec SCSI Card 29320A.
3Plug the other end of the cable to a terminated Ultra/Fast
Narrow SCSI device.
4If you have other Ultra/Fast Narrow SCSI devices, attach them
to the connectors between the two ends of the cable. Be sure
these other devices are unterminated.
5Connect a power cable from your computer’s internal power
supply to each internal device.
Connecting External SCSI Devices
You can connect external Ultra320/160 and Ultra2 SCSI devices to
the 68-pin external LVD SCSI connector. Each external device will
require a 68-pin LVD external LVD SCSI cable.
Note: We recommend that you do not combine older SCSI
devices with the newer Ultra320/160 and Ultra2 SCSI devices
on the same SCSI channel of the Adaptec SCSI Card 29320A.
Follow these steps to connect your external SCSI devices:
1Connect one end of an external SCSI cable to one of the external
Ultra320/160 connectors on the Adaptec SCSI Card 29320A.
68-pin external
LVD SCSI connector External LVD SCSI
cable
ASC-29320A IG.fm Page 8 Tuesday, July 29, 2003 3:30 PM
9
2Connect the other end of the cable to a SCSI connector on the
back of an external device. If you are installing only one
external device, terminate the device and skip to Step 4.
3Connect the other external SCSI devices by linking each device
to the previous one, as shown below. Terminate only the device
at the end of the chain.
4Connect power cables to all external device(s) and to the
computer.
4
4
SCSI terminator
ASC-29320A IG.fm Page 9 Tuesday, July 29, 2003 3:30 PM
Indice
Altri manuali Adaptec Adattatore
Adaptec
Adaptec T460 SlimSCSI Manuale
Adaptec
Adaptec APA-9315 Manuale di installazione e funzionamento
Adaptec
Adaptec AHA-3985 Guida rapida
Adaptec
Adaptec AUA-1420 Manuale utente
Adaptec
Adaptec Adaptec RAID Controller Manuale utente
Adaptec
Adaptec 9210LP Manuale di servizio
Adaptec
Adaptec AFW-1430 Manuale utente
Adaptec
Adaptec AHA-1522B Manuale di istruzioni
Adaptec
Adaptec AHA-1540C Manuale utente
Adaptec
Adaptec ANA-6910/FX SC Manuale utente
Adaptec
Adaptec PC/104 Manuale utente
Adaptec
Adaptec AHA-2740W Manuale utente
Adaptec
Adaptec XHub4 - Hub - USB Manuale utente
Adaptec
Adaptec SlimSCSI 1450 Manuale utente
Adaptec
Adaptec ASR-2000S Manuale utente
Adaptec
Adaptec AFW-4300 Manuale
Adaptec
Adaptec AHA-1510 Manuale utente
Adaptec
Adaptec ASH-1205SA Manuale utente
Adaptec
Adaptec Trantor T348 Manuale
Adaptec
Adaptec APA-1350 Manuale utente
