Adaptec M3093GX Manuale operativo e di manutenzione

M3093GX\DG\M3096G\GX\M3097G+\DG

Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI

Win2000\XP Installation Procedure

Rev050304A

Step A: Required hardware.

To install these models you will need a Narrow SCSI 50-pin controller and six foot (maximum)

Narrow SCSI cable.

Step B: Removing the shipping bracket.

It is recommended that before you connect the scanner to your computer that you inspect the

scanner and remove the shipping bracket first.

Removing the shipping bracket: The flatbed scanner models typically come with a

factory installed shipping lock designed to protect the scanner during shipment. Before

the scanner can be used the shipping lock must be unlocked. Follow these instructions

to unlock the shipping bracket:

1. Slide the scanner to its side as shown in figure below.

2. Unscrew the retainer screw and remove the shipping bracket.

3. Place the shipping bracket in the “use position” slot and secure it with the retainer

screw (see figure below)

4. Place scanner back in its normal position

M3093GX\DG\M3096G\GX\M3097G+\DG

Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI

Win2000\XP Installation Procedure

Rev050304A

Special note: The Fi-4340C shipping lock is a knob located underneath the exit tray. To unlock

it twist a quarter turn counter-clockwise so that it is vertical. The Fi-4530C does not have a

shipping lock.

Step C: Installing the SCSI Host Adapter.

1. Shut down your PC and remove the case cover.

2. Locate a free PCI slot and remove the back plate if necessary.

3. Install the SCSI controller in an open PCI slot.

Make sure that the card is seated completely in the slot and secured in the frame

Warning! Failure to secure the SCSI controller in the PC can result in damage to the

SCSI card, scanner, and/or your system.

4. Boot your PC without the scanner attached.

Step D: Installing the SCSI drivers (Adaptec).

1. When the New Hardware wizard comes up, allow Windows to finish installing the

files for the SCSI controller.

2. Then go to www.adaptec.com, and click on the “search” tab. Scroll down to the

“Enter key word or quoted phrase” box and type in “aspi”.

3. Next scroll down to the drivers section, click on ASPI_v470 or higher and follow the

prompts to download it.

4. Afterwards go to that folder and unzip the file to the default Adaptec\ASPI folder. For

Win2000 go to start, run, browse to the Adaptec\ASPI folder, select ASPIINST.EXE

and run it. For WinXP go to start, run, browse to the Adaptec\ASPI folder, select

INSTALL.BAT file in the directory the files extracted to and select the OPEN button.

In the command box, add a space and either XP32 for Pentium I/II/III/IV processors

or XP64 for Itanium processors. The command should look like:

c:\adaptec\aspi\install.bat XP32 or c:\adaptec\aspi\install.bat XP64. Then select

the OK button to run it.

5. Reboot and check for errors. If no errors shut down your system and go to the next

step.

Step E: Connecting the Scanner.

Warning! Ensure power is off when connecting or disconnecting any cables to the scanner or

workstation.

Setting the SCSI ID: The factory setting for the Scanner is 6, however, selecting a

different SCSI ID may be required when there are several devices on a SCSI chain.

Using a suitable tool, turn the selector switch until the arrow points to the desired ID

number (see figure 2-3). Setting the SCSI ID to 0, 1, or 7 is NOT recommended as these

settings are typically reserved for hard drives and the SCSI host adapter.

Setting Termination: The Fujitsu M3093GX\M3096G\GX\M3097G+\DG scanners come

with a plug in SCSI terminator (see figure below). The Fi-4340C\Fi-4640S\M4097D\Fi-

4750C\L scanners come with built in termination that is turned on or off through the

scanner panel. Termination for the Fi-4530C is handled automatically by the scanner. If

the scanner is the last device on the SCSI chain then the terminator should be placed on

M3093GX\DG\M3096G\GX\M3097G+\DG

Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI

Win2000\XP Installation Procedure

Rev050304A

one of the SCSI ports or turned on. If the scanner is not the last device on the SCSI

chain, then the terminator should be removed or turned off before connecting to the next

SCSI device.

Connecting SCSI cable: Located on the back of the scanner are the SCSI ports.

Depending on the model the ports may be either a High Density 50-pin (HD-50) or a 50-

pin Centronics. Use the appropriate cable to connect the scanner to the SCSI controller

in your PC. Ensure all connections are securely fastened.

Powering On: Connect the power cord to the scanner and a wall outlet then turn on the

scanner. For those models without a power switch plug in the power supply to the back

of the scanner. For proper communication between the Scanner and the Workstation,

switch on the scanner prior to switching on the workstation. The scanner power and

LCD display will light up. Next after the scanner completes its startup initialization the

LCD will display either ready or the number one. This indicates that the scanner is

ready.

Step F: Installing the ISIS driver.

1. Create a new folder and name it ISIS Download.

2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.

3. In the sub frame under the Product Support column click on Scanners.

4. On the next page select Drivers and Downloads.

5. Afterwards click on ISIS Software Drivers.

6. Locate the appropriate ISIS driver for your scanner by cross-referencing the scanner

model column on the left to the software column.

7. Double click on the driver file name and the File Download box will popup.

8. Click on Save and then use the browse (or other folder navigation) button until you

have the ISIS Download folder you created in the Save In Box.

9. Click Save.

10. When completed close the Download Complete window and go to the ISIS

Download folder.

11. Open the folder and you will see the saved ISIS driver file. Double click on the file to

unzip it and the WinZip* self-extractor box will popup. Click on browse and select the

M3093GX\DG\M3096G\GX\M3097G+\DG

Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI

Win2000\XP Installation Procedure

Rev050304A

ISIS Download folder, then click on Extract. The file will begin to unzip and when

finished a message box will report the number of files unzipped. Click on OK and

close WinZip.

12. In the ISIS Download folder locate the setup.exe file and double click. Afterwards

follow the prompts and reboot when finished.

Step G: Installing the STI-Twain driver for the Fi-4340C\Fi-4530C\Fi-4640S\M4097D\

Fi-4750C\L\Fi-5750.

Special note: Use the ASPI-Twain driver for the M3093GX\DG\M3096G\GX\M3097G+\DG.

1. Create a new folder and name it Twain Download.

2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.

3. In the sub frame under the Product Support column click on Scanners.

4. On the next page select Drivers and Downloads.

5. Afterwards click on STI Twain Software Drivers.

6. Locate the appropriate STI Twain driver for your scanner by cross-referencing the

scanner model column on the left to the software column.

7. Double click on the driver file name and the File Download box will popup.

8. Click on Save and then use the browse (or other folder navigation) button until you

have the Twain Download folder you created in the Save In Box.

9. Click Save.

10. When completed close the Download Complete window and go to the Twain

Download folder.

11. Open the folder and you will see the saved STI Twain driver file. Double click on the

file to unzip it and the WinZip* self-extractor box will popup. Click on browse and

select the STI Twain Download folder, then click on Extract. The file will begin to

unzip and when finished a message box will report the number of files unzipped.

Click on OK and close WinZip.

12. In the STI Twain Download folder locate the setup.exe file and double click.

Afterwards follow the prompts and reboot when finished.

Step H: Installing the Twain driver for the M3093GX\DG\M3096G\GX\M3097G+\DG.

1. Create a new folder and name it Twain Download.

2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.

3. In the sub frame under the Product Support column click on Scanners.

4. On the next page select Drivers and Downloads.

5. Afterwards click on ASPI Twain Software Drivers.

6. Locate the appropriate ASPI Twain driver for your scanner by cross-referencing the

scanner model column on the left to the software column.

7. Double click on the driver file name and the File Download box will popup.

8. Click on Save and then use the browse (or other folder navigation) button until you

have the Twain Download folder you created in the Save In Box.

9. Click Save.

10. When completed close the Download Complete window and go to the Twain

Download folder.

11. Open the folder and you will see the saved ASPI Twain driver file. Double click on

the file to unzip it and the WinZip* self-extractor box will popup. Click on browse and

select the ASPI Twain Download folder, then click on Extract. The file will begin to

unzip and when finished a message box will report the number of files unzipped.

Click on OK and close WinZip.

M3093GX\DG\M3096G\GX\M3097G+\DG

Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI

Win2000\XP Installation Procedure

Rev050304A

12. In the ASPI Twain Download folder locate the setup.exe file and double click.

Afterwards follow the prompts and reboot when finished.

Step H: Installing Scandall21.

1. Create a new folder and name it Scandall Download.

2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.

3. In the sub frame under the Product Support column click on Scanners.

4. On the next page select your Drivers and Downloads.

5. Afterwards click on Software Utilities.

6. Double click on the file name and the File Download box will popup.

7. Click on Save and then use the browse (or other folder navigation) button until you

have the Scandall Download folder you created in the Save In Box.

8. Click Save.

9. When completed close the Download Complete window and go to the Scandall

Download folder.

10. Open the folder and you will see the saved Scandall file. Double click on the file to

unzip it and the WinZip* self-extractor box will popup. Click on browse and select the

Scandall Download folder, then click on Extract. The file will begin to unzip and

when finished a message box will report the number of files unzipped. Click on OK

and close WinZip.

11. In the Scandall Download folder locate the Scandall.exe file and double click.

Afterwards follow the prompts and when finish launch Scandall.

Step I: Scanning with Scandall21.

Once Scandall21 is installed it is time to start scanning.

1. Launch Scandall21 by clicking on the shortcut link on your desktop or manually by

clicking on Start, Programs, Scanner Utility for Microsoft Windows, then

Scandall21.

2. After the Untitled Screen has open, click on Scan and choose Select Source.

3. Select the Fujitsu Twain source for your scanner by highlighting it and clicking

OK. You will only need to do this once unless you are scanning with multiple

sources.

4. Once you are back at the Untitled Screen click on Scan and select To View this

time. The Twain User Interface will popup.

5. Select the scanning parameters that you wish to use – Color mode, resolution,

paper size, etc…

6. Next under Scan Type choose either ADF or Flatbed in the dropdown box.

7. Place your document in the ADF or on the Flatbed face down and click on the Scan

button.

8. After the document is scanned close the Twain User Interface and the image will

appear on the Untitled Screen.

Congratulations! You have successfully completed your scanner installation.

*If you do not have any unzipping software installed on your system, you can download a free

evaluation copy at www.winzip.com.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Adaptec Hardware per computer

Adaptec

Adaptec 2025ZCR - SCSI RAID Storage Controller Manuale utente

Adaptec

Adaptec P Class 733/800/866MHz / 1GHz Manuale utente

Adaptec

Adaptec ATA II 1220SA Manuale utente

Adaptec

Adaptec 2045 Manuale utente

Adaptec

Adaptec ASR-6805Q Manuale utente

Adaptec

Adaptec AAR-1220SA Manuale di istruzioni

Adaptec

Adaptec ACB-232XD Manuale utente

Adaptec

Adaptec 1220SA - RAID Controller Manuale utente

Adaptec

Adaptec RAID 6805Q Manuale utente

Adaptec

Adaptec RAID 2405 Manuale utente

Adaptec

Adaptec AAA-130U2 SERIES Istruzioni di montaggio

Adaptec

Adaptec SAS RAID Controllers Manuale utente

Adaptec

Adaptec 2940U2W - Storage Controller U2W SCSI 80... Manuale utente

Adaptec

Adaptec RAID 5405Z Manuale utente

Adaptec

Adaptec ASR-3085 Manuale operativo

Adaptec

Adaptec AHA-1520 Manuale utente

Adaptec

Adaptec SATA RAID FOR ADAPTEC Manuale utente

Adaptec

Adaptec 2100S - SCSI RAID Controller Manuale utente

Adaptec

Adaptec PM2865U3 Manuale utente

Adaptec

Adaptec ASR-3085 Manuale operativo

Adaptec

Adaptec AFM-600 Manuale utente

Adaptec

Adaptec PM1564U3 Manuale utente

Adaptec

Adaptec ICP 5045BL Manuale utente

Adaptec

Adaptec AAR-1420SA Manuale di istruzioni

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente