ADB M 5083 Manuale utente

M5083 1106.05.083

Lighting Technologies

User Manual

Issue 1.1

Motorised WARP

Disclaimer

www.adblighting.com User Manual - page 1

Issue 1.1

Disclaimer

Advice before Use

Read these instructions carefully.

As soon as the equipment is delivered, open packing and inspect the equipment carefully. If

you notice any damage, contact the transport company immediately and register your

complaint in due form listing the defects. Check if the received equipment is consistent with

the delivery note and if this delivery note is consistent with your order. If it is not, contact your

supplier immediately.

Warning

The luminaire may under no circumstances be modified. ADB will not assume any

responsibility in case of damage resulting from modifications made to the luminaire. Always

refer to authorized personnel for any repair.

Warranty

See our general conditions of sales; available on our Web Site.

Warranty sheet1

1Enclose with each Motorised WARP

Safety notice

User Manual - page 2 www.adblighting.com

Issue 1.1

Declaration of conformity

This luminaire is a piece of lighting equipment designed for professional indoor use in

theatres and television or film studios. Designed and built in accordance with EN 60598-1

and EN 60598-2-17 regulations, it must imperatively be connected to earth by means of its

earth wire. To prevent any electrical shock, this equipment should not be opened when it is

powered up. Access to internal parts is not required for normal operation.

Any parts or lenses need to be replaced if they are visibly damaged and their efficiency might

be reduced, e. g. in case of deep cracks or scratches. The lamp must be changed if

damaged or distorted by heat. If internal access is needed for control, service or repair

purposes, always refer to qualified personnel.

Standards and approvals

Safety standards: EN 60598-1 and EN 60598-2-17

EMC standards: EN 55022, Class A limits for emission and EN 50081-1, EN 50082-1

Susceptibility: IEC 801-2, IEC 801-3 and IEC 801-4

Safety Notice

www.adblighting.com User Manual - page 3

Issue 1.1

Safety Notice

Always be sure to unplug the power supply cable before opening the fixture. It is the user's

responsibility to use the luminaire for its intended purpose and to check the equipment that

might be connected to it.

Power supply cables and other connections are essential for your equipment and contribute

greatly to a safe and trouble free operation. Always pull the plug when disconnecting a cable,

never pull the cable. Never use cables or connectors in bad condition. Check them before

installation and periodically thereafter. Never tie power supply and data cables together.

This luminaire is designed for operating at a nominal voltage of 230 V (90 – 230 V in case of

automatic power supply option). For your own safety, make sure the earth wire (yellow-

green) is ALWAYS connected to earth.

WARNING: LETHAL VOLTAGE PRESENT INSIDE!

Foreword

User Manual - page 4 www.adblighting.com

Issue 1.1

Foreword

This issue 1.0 of the User Manual for Motorised WARP.

The latest version of ADB User Manuals is available from the ADB website.

www.adblighting.com > ADB Products > Product family > Product

For WARP and Motorised WARP

www.adblighting.com > ADB Products > Theatre Luminaires > WARP Motorised

The functions described in this User Manual require the latest software version. The latest

software version is available on the ADB TTV R&D web site.

http://adbttv.dyndns.org/index.php?title=Warp&article=warp

Updates to this version of the user manual will follow.

Have fun with the motorised profile.

Zaventem, January 13, 2006.

Index

www.adblighting.com User Manual - page 5

Issue 1.1

Index

DISCLAIMER....................................................................................................................................................... 1

Advice before Use........................................................................................................................... 1

Warning........................................................................................................................................... 1

Warranty ......................................................................................................................................... 1

Warranty sheet................................................................................................................................ 1

DECLARATION OF CONFORMITY............................................................................................................... 2

Standards and approvals................................................................................................................ 2

SAFETY NOTICE................................................................................................................................................ 3

FOREWORD......................................................................................................................................................... 4

INDEX.................................................................................................................................................................... 5

1SHIPPING CONTENTS............................................................................................................................ 8

1.1 WARP/M INCLUDES: ............................................................................................................... 8

1.2 OPTIONAL ............................................................................................................................ 9

1.2.1 Lamp .................................................................................................................................. 9

1.2.2 Hook clamp for WARP/M...................................................................................................... 9

1.2.3 Accessories........................................................................................................................ 9

1.2.4 Color Changer.................................................................................................................... 9

2DESCRIPTION........................................................................................................................................ 10

2.1 FEATURES ......................................................................................................................... 10

2.1.1 Standard features ............................................................................................................ 10

2.1.2 Control and feedback....................................................................................................... 10

2.1.3 Optional features ............................................................................................................. 10

2.2 COMPONENTS.................................................................................................................... 11

2.2.1 Overview .......................................................................................................................... 11

2.2.2 TOPBOX ..........................................................................................................................12

2.2.3 XLR4 connector on the motor-house.............................................................................. 13

2.2.4 Accessories...................................................................................................................... 14

2.2.4.1 Hook clamps........................................................................................................................................ 14

2.2.4.2 Double gobo holder............................................................................................................................. 15

2.2.4.3 Combined iris diaphragm & gobo holder............................................................................................ 15

3INSTALLATION..................................................................................................................................... 16

3.1 MOUNTING......................................................................................................................... 16

3.2 POWER AND DATA CABLING REQUIREMENTS ....................................................................... 16

3.2.1 Mains power for the control electronics ........................................................................... 16

3.2.2 Lamp power ..................................................................................................................... 16

3.2.3 DMX data and termination when WARP receives DMX..................................................... 16

3.2.4 DMX data and termination when WARP is transmitting DMX............................................ 16

3.2.5 Ethernet ........................................................................................................................... 17

3.3 INSTALLATION PROCEDURES............................................................................................... 17

3.3.1 Inserting (replacing) the lamp .......................................................................................... 17

3.3.2 Alignment of the lamp ...................................................................................................... 18

3.3.3 Suggested procedure to align the lamp........................................................................... 19

3.4 PAN &TILT –‘RESET’VERSUS ‘ABSOLUTE VALUES’............................................................ 21

3.4.1 Internal jumpers ............................................................................................................... 22

3.4.2 Jumper setting ................................................................................................................. 23

3.5 BALANCING........................................................................................................................ 24

3.5.1 Factory-balancing of the WARP......................................................................................... 24

3.5.2 On-site balancing of a WARP............................................................................................. 24

3.5.2.1 Advice for balancing........................................................................................................................... 24

Index

User Manual - page 6 www.adblighting.com

Issue 1.1

3.6 LEARN BOUNDARIES FOR PAN &TILT .................................................................................. 25

3.7 CONFIGURATION –PRESENCE OF IRIS/GOBO HOLDER ........................................................... 25

3.8 POWERING UP.................................................................................................................... 26

4MENU STRUCTURE.............................................................................................................................. 27

4.1 PUSH-BUTTONS AND LEDS................................................................................................. 27

4.1.1 LEDs ................................................................................................................................ 27

4.1.2 Push-buttons....................................................................................................................27

4.2 MENU FUNCTIONS –LOCAL DISPLAY .................................................................................... 28

4.3 DMX ADDRESSING ............................................................................................................. 32

4.3.1 DMX address ................................................................................................................... 32

4.3.2 Priority rule between DMX and ArtDMX .......................................................................... 32

5OPERATION............................................................................................................................................ 33

5.1 DMX OPERATION............................................................................................................... 33

5.1.1 Channel Mapping............................................................................................................. 33

5.1.2 Rotate 720°...................................................................................................................... 34

5.1.3 How to identify a shutter shutter on your console............................................................ 34

5.2 DMX MAPPING –THE CONTROL CHANNEL ........................................................................... 35

5.2.1 Control Channel............................................................................................................... 35

6WEB PAGE .............................................................................................................................................. 37

6.1 WARP’SIP ADDRESS ............................................................................................................ 37

6.2 HOME PAGE ....................................................................................................................... 38

6.3 WARP SCANNER.................................................................................................................. 39

6.4 DMX CHANNELS ................................................................................................................ 40

6.5 ARTNET CONFIGURATION ................................................................................................... 41

6.6 INFORMATION..................................................................................................................... 42

6.7 AXES AND WHEELS CONFIGURATION ................................................................................... 43

6.8 LAMP RELAY ...................................................................................................................... 45

6.9 FIRMWARE UPDATE ............................................................................................................ 46

6.10 MISCELLANEOUS................................................................................................................ 47

6.11 RESET WARP...................................................................................................................... 49

6.12 CALIBRATION ..................................................................................................................... 50

7MESSAGES ON LOCAL DISPLAY...................................................................................................... 52

7.1 LOCAL WARP MESSAGES ..................................................................................................... 52

7.2 LOCAL CALIBRATION AND RESET MESSAGES......................................................................... 52

7.3 LOCAL ERROR MESSAGES.................................................................................................. 53

8TROUBLESHOOTING AND MAINTENANCE.................................................................................. 54

8.1 SOFTWARE UPLOAD ........................................................................................................... 54

8.2 AUTO-TEST ROUTINE AT POWER UP ..................................................................................... 55

8.3 CLEANING WARP................................................................................................................. 55

8.3.1 Cleaning Lenses .............................................................................................................. 55

8.3.2 Cleaning optical sensors and shutters............................................................................. 56

9TECHNICAL SPECIFICATIONS......................................................................................................... 57

9.1 RANGES AND SPEED (TIME)................................................................................................. 57

THE INDICATION FOR SPEED IS THE TIME TO COVER THE FULL RANGE,EXPRESSED IN SECONDS.......... 57

9.1.1 Weight and size ............................................................................................................... 57

9.1.2 Construction materials ..................................................................................................... 58

9.1.3 Electrical .......................................................................................................................... 58

10 HELPFUL TIPS....................................................................................................................................... 59

10.1 HOW TO INSERT OR REMOVE AN ACCESSORY ....................................................................... 59

10.1.1 Convention....................................................................................................................... 59

10.1.2 How to insert the iris / gobo holder .................................................................................. 59

10.1.3 How to remove iris / gobo holder..................................................................................... 60

10.2 HOW TO ADD A COLOUR SCROLLER ..................................................................................... 61

10.2.1 Convention if not ADB scroller......................................................................................... 61

Index

www.adblighting.com User Manual - page 7

Issue 1.1

10.2.2 Pin out definition of the 4 Pin output connector ............................................................... 61

10.2.3 Adding the scroller ........................................................................................................... 62

10.2.4 DMX mapping for the colour scroller ............................................................................... 62

10.2.5 Removing the scroller ...................................................................................................... 62

11 ADDENDA................................................................................................................................................ 63

11.1 ADDENDUM 1: HOW TO SET-UP A NETWORK CARD FOR ARTNET (WINXP) ............................. 63

11.2 ADDENDUM 2: DOWNLOADING OF PERSONALITIES FOR CONSOLES ........................................ 64

12 SPARE PARTS......................................................................................................................................... 65

13 NOTES...................................................................................................................................................... 66