ADTRAN Cable T1 ESF CSU ACE Manuale utente

T1 ESF CSU ACE

User Manual

1204025L1 T1 ESF CSU ACE

61204025L1-1B

September 2004

Trademarks

Any brand names and product names included in this manual are trademarks, registered trademarks, or

trade names of their respective holders.

To the Holder of the Manual

The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change

the contents without prior notice.

In no event will ADTRAN be liable for any special, incidental, or consequential damages or for

commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

Printed in U.S.A.

Safety Instructions

When using your telephone equipment, please follow these basic safety precautions to reduce the risk of

fire, electrical shock, or personal injury:

1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a

wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote

risk of shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of

batteries in a fire. They may explode. Check with local codes for special disposal instructions.

Save These Important Safety Instructions

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the equipment or

endangerment to human life.

Affidavit Requirements for Connection to Digital Services

• An affidavit is required to be given to the telephone company whenever digital terminal equipment

without encoded analog content and billing protection is used to transmit digital signals containing

encoded analog content which are intended for eventual conversion into voiceband analog signals and

transmitted on the network.

• The affidavit shall affirm that either no encoded analog content or billing information is being

transmitted or that the output of the device meets Part 68 encoded analog content or billing protection

specifications.

• End user/customer will be responsible for filing an affidavit with the local exchange carrier when

connecting unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital services.

Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit

requirement for subrate services is waived.

Affidavit for Connection of Customer Premises Equipment

to 1.544 Mbps and/or Subrate Digital Services

For the work to be performed in the certified territory of ___________________ (telco name)

State of ________________

County of ________________

I, _______________________ (name), ____________________________________ (business address),

____________________ (telephone number) being duly sworn, state:

I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or ________ subrate

digital services. The terminal equipment tobe connected complies with Part 68of the FCC rules except for the encoded analog content and

billing protection specifications. With respect to encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with respect to analog content

and encoded billing protection information continuously complies with Part 68 of the FCC Rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encoded analog content or billing information which is intended to be decoded

within the telecommunications network.

( ) The encoded analog content and billing protection is factory set and is not under the control of the customer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and adjustment of the

encoded analog content and billing information has (have) been trained to perform these functions by successfully having completed one

of the following (check appropriate blocks):

( ) A. A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or

( ) B. A training course provided by the customer or authorized representative, using training materials and instructions provided by the

manufacturer/grantee of the equipment used to encode analog signals; or

( ) C. An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the equipment

used to encode analog signals; or

( ) D. In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the control of a supervisor trained in

accordance with _________ (circle one) above.

I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the information as

provided in the preceding paragraph, if so requested.

_________________________________Signature

_________________________________Title

_________________________________ Date

Transcribed and sworn to before me

This ________ day of _______________, _______

_________________________________

Notary Public

My commission expires:

_________________________________

FCC regulations require that the following information be provided in this manual:

1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. On the

equipment housing is a label that contains, among other information, a product identifier in the

format US: AAAEQ##TXXXX. If requested, provide this information to the telephone company.

2. If this equipment causes harm to the telephone network, the telephone company may temporarily

discontinue service. If possible, advance notification is given; otherwise, notification is given as

soon as possible. The telephone company will advise the customer of the right to file a complaint

with the FCC.

3. The telephone company may make changes in its facilities, equipment, operations, or procedures

that could affect the proper operation of this equipment. Advance notification and the opportunity

to maintain uninterrupted service are given.

4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty

information. The telephone company may require this equipment to be disconnected from the

network until the problem is corrected or it is certain the equipment is not malfunctioning.

5. This unit contains no user-serviceable parts.

6. An FCC compliant telephone cord with a modular plug is provided with this equipment. This

equipment is designed to be connected to the telephone network or premises wiring using an FCC

compatible modular jack, which is compliant with Part 68 and requirements adopted by ACTA.

7. The following information may be required when applying to the local telephone company for a

dial-up line for the V.34 modem:

8. The REN is useful in determining the quantity of devices you may connect to your telephone line

and still have all of those devices ring when your number is called. In most areas, the sum of the

RENs of all devices should not exceed five. To be certain of the number of devices you may

connect to your line as determined by the REN, call your telephone company to determine the

maximum REN for your calling area.

9. This equipment may not be used on coin service provided by the telephone company. Connection

to party lines is subject to state tariffs. Contact your state public utility commission or corporation

commission for information.

Service Type REN/SOC FIC USOC

1.544 Mbps - SF 6.0N 04DU9-BN RJ48C

1.544 Mbps - SF and B8ZS 6.0N 04DU9-DN RJ48C

1.544 Mbps - ESF 6.0N 04DU9-1KN RJ48C

1.544 Mbps - ESF and B8ZS 6.0N 04DU9-1SN RJ48C

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.

Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

Industry Canada Compliance Information

Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the

“IC:” in front of the certification/registration number) signifies that the Industry Canada technical

specifications were met.

Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the

documentation or on the product labeling/markings. The REN assigned to each terminal device indicates

the maximum number of terminals that can be connected to a telephone interface. The termination on an

interface may consist of any combination of devices subject only to the requirement that the sum of the

RENs of all the devices should not exceed five (5).

Canadian Emissions Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus

as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the

Department of Communications.

Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques

de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee

par le ministre des Communications.

Warranty and Customer Service

ADTRAN will repair and return this product within 5 years from the date of shipment if it does not meet its

published specifications or fails while in service. For detailed warranty, repair, and return information refer

to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure.

Return Material Authorization (RMA) is required prior to returning equipment to ADTRAN.

For service, RMA requests, or further information, contact one of the numbers listed at the end of this

section.

LIMITED PRODUCT WARRANTY

ADTRAN warrants that for 5 years from the date of shipment to Customer, all products manufactured by

ADTRAN will be free from defects in materials and workmanship. ADTRAN also warrants that products

will conform to the applicable specifications and drawings for such products, as contained in the Product

Manual or in ADTRAN’s internal specifications and drawings for such products (which may or may not be

reflected in the Product Manual). This warranty only applies if Customer gives ADTRAN written notice of

defects during the warranty period. Upon such notice, ADTRAN will, at its option, either repair or replace

the defective item. If ADTRAN is unable, in a reasonable time, to repair or replace any equipment to a

condition as warranted, Customer is entitled to a full refund of the purchase price upon return of the

equipment to ADTRAN. This warranty applies only to the original purchaser and is not transferable

without ADTRAN’s express written permission. This warranty becomes null and void if Customer

modifies or alters the equipment in any way, other than as specifically authorized by ADTRAN.

EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THE FOREGOING

CONSTITUTES THE SOLE AND EXCLUSIVE REMEDY OF THE CUSTOMER AND THE

EXCLUSIVE LIABILITY OF ADTRAN AND IS IN LIEU OF ANY AND ALL OTHER WARRANTIES

(EXPRESSED OR IMPLIED). ADTRAN SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES,

INCLUDING (WITHOUT LIMITATION), ALL WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. SOME STATES DO NOT ALLOW THE EXCLUSION

OF IMPLIED WARRANTIES, SO THIS EXCLUSION MAY NOT APPLY TO CUSTOMER.

In no event will ADTRAN or its suppliers be liable to the Customer for any incidental, special, punitive,

exemplary or consequential damages experienced by either the Customer or a third party (including, but

not limited to, loss of data or information, loss of profits, or loss of use). ADTRAN is not liable for

damages for any cause whatsoever (whether based in contract, tort, or otherwise) in excess of the amount

paid for the item. Some states do not allow the limitation or exclusion of liability for incidental or

consequential damages, so the above limitation or exclusion may not apply to the Customer.

Customer Service, Product Support Information, and Training

ADTRAN will repair and return this product if within 5 years from the date of shipment the product does

not meet its published specification or the product fails while in service.

A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,

RMA requests, training, or more information, use the contact information given below.

Repair and Return

If you determine that a repair is needed, please contact our Customer and Product Service (CAPS)

department to have an RMA number issued. CAPS should also be contacted to obtain information

regarding equipment currently in house or possible fees associated with repair.

Identify the RMA number clearly on the package (below address), and return to the following address:

Pre-Sales Inquiries and Applications Support

Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,

the ADTRAN Support web site provides a variety of support services such as a searchable knowledge

base, latest product documentation, application briefs, case studies, and a link to submit a question to an

Applications Engineer. All of this, and more, is available at:

When needed, further pre-sales assistance is available by calling our Applications Engineering

Department.

Post-Sale Support

Your reseller should serve as the first point of contact for support. If additional support is needed, the

ADTRAN Support web site provides a variety of support services such as a searchable knowledge base,

updated firmware releases, latest product documentation, service request ticket generation and trouble-

shooting tools. All of this, and more, is available at:

When needed, further post-sales assistance is available by calling our Technical Support Center. Please

CAPS Department (256) 963-8722

ADTRAN Customer and Product Service

901 Explorer Blvd. (East Tower)

Huntsville, Alabama 35806

RMA # _____________

http://support.adtran.com

Applications Engineering (800) 615-1176

http://support.adtran.com

Altri manuali per Cable T1 ESF CSU ACE

Indice

Altri manuali ADTRAN Hardware di rete

ADTRAN

ADTRAN Fractional T1 Tandem Channel Unit FT1-TDM Manuale utente

ADTRAN

ADTRAN DSU IQ Manuale utente

ADTRAN

ADTRAN T200 IDSL Manuale di istruzioni

ADTRAN

ADTRAN NetVanta Serial Dial Backup Interface Module (DIM)... Manuale utente

ADTRAN

ADTRAN jobAid Total Access 838 Manuale utente

ADTRAN

ADTRAN Total Access 3000 Manuale

ADTRAN

ADTRAN NetVanta 2000 Series Guida utente

ADTRAN

ADTRAN TOTAL ACCESS 600R Manuale utente

ADTRAN

ADTRAN DDM+ H2TU-C Manuale di istruzioni

ADTRAN

ADTRAN 411 Manuale utente

ADTRAN

ADTRAN Total Access 1500 Dual FXS/DPO Manuale utente

ADTRAN

ADTRAN DSU III ARdc Manuale utente

ADTRAN

ADTRAN OC-12 Manuale utente

ADTRAN

ADTRAN 6540 Manuale di istruzioni

ADTRAN

ADTRAN T200 IDSL OCU-R Manuale di istruzioni

ADTRAN

ADTRAN Smart 16e Shelf Manuale utente

ADTRAN

ADTRAN MX2820-48 VDC M13 MUX Manuale utente

ADTRAN

ADTRAN QFO-C Manuale di istruzioni

ADTRAN

ADTRAN 1202801L1 Manuale utente

ADTRAN

ADTRAN Express 3000 Manuale utente

ADTRAN

ADTRAN BR1/10 PAU Manuale di istruzioni

ADTRAN

ADTRAN NETVANTA 6355 Manuale utente

ADTRAN

ADTRAN DS3 NIU3 Manuale di istruzioni

ADTRAN

ADTRAN NetVanta NetVanta ADSL NIM Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente