ADTRAN TRACER 4205 Manuale utente

Converting the Frequency Plan of a TRACER 4205 System

Introduction

TRACER 4205 systems are shipped from the factory with the frequency plan programmed as Plan A or Plan B.

Each wireless link must contain a Plan A radio on one end and a Plan B on the other. A frequency plan

conversion may be performed in the field, but should only be attempted if absolutely necessary and must

always be performed by qualified personnel. This document outlines the procedure for changing the frequency

plan of a TRACER 4205 system.

Prerequisite Procedures

The current frequency plan configuration is listed on a label located on the rear panel of the unit (near the

Antenna connector). Record the current configuration before beginning this procedure.

Tools and Materials Required

• 5/16” Torque wrench (8 in-lbs)

• 3/16” nut driver

• Phillips-head screw driver

Disconnect all cables attached to the TRACER 4205 system (including power, data,

terminal RS-232, etc.) before performing this procedure.

Do not attempt to perform the conversion without the proper tools (see list below). Using

improper tools will damage the unit.

Electronic equipment can be damaged by static electrical discharge. Before handling

equipment, put on an antistatic discharge wrist strap to prevent damage to components.

Place equipment in antistatic packing material when transporting or storing. When

working on equipment, always place it on an approved antistatic mat that is electrically

grounded.

TRACER 4205 Frequency Conversion Document

1. Remove the screws from the chassis cover using a Phillips-head screwdriver (see Figure 1).

Figure 1. Removing the Cover Screws (TRACER 4205)

2. Remove the nuts on either side of the RS-232 connector (on the rear panel of the unit) using the 3/16”

nut driver (see Figure 2).

Figure 2. Removing the RS-232 Nuts

3. Carefully slide the cover toward the back of the unit until the front edge of the cover is disconnected

from the front of the unit. Lift the cover off and set aside.

Perform the steps below in the order listed.

Remove all connected mounting brackets before attempting to remove the unit cover.

TRACER 4205 Frequency Conversion Document

4. Verify the current frequency plan configuration. To verify the plan, check the connections between the

J connectors (located on the board and labeled J1 and J2) and the Chan connectors (located on the

diplexer). The Chan connectors are labeled CH1 and CH2 for most TRACER 4205 systems. The

following table outlines the connections for Plan A and B.

Click to see a digital image of the J connectors or the Chan connectors.

5. Using the torque wrench, disconnect both cables from the Chan connectors on the diplexer. Do not

attempt to disconnect the J connectors (located on the board) as this will cause damage. Click here for

a digital picture of this step.

6. Carefully flex the cables to swap the connections. Be careful with the RF cables, making sure that the

minimum bend radius of the cable is greater than 0.75"; bends and loops smaller than a quarter will

cause the RF cable to break. Use the wiring guidelines in Figure 3 for help with wire placement. Click

here for a digital picture of this step.

Figure 3. TRACER 4205 Cable Routing Diagrams

TRACER 4205

PLAN CHAN 1 CHAN 2

AJ2 J1

BJ1 J2

Allowing the RF cables to sit on the processor and radio boards (green) could cause

damage to the boards; keep the RF cables off the boards while re-routing them. Click here

for a digital picture of this mistake.

CH2 CH1

J1 J2

CH2 CH1

J1 J2

TRACER 4205 Frequency Conversion Document

7. Use the torque wrench to reconnect the RF cables to the Chan connectors. Tighten the cables by

turning clockwise until you hear a click from the wrench. DO NOT overtighten connectors as this will

cause the RF cable to break. The TRACER 4205 system will not operate properly with broken RF

cables.

8. Reinstall the cover and carefully tighten all screws.

9. Change label on back of the unit to reflect the Plan change.

>> BACK

Altri manuali ADTRAN Hardware di rete

ADTRAN

ADTRAN Total Access 351 Manuale utente

ADTRAN

ADTRAN ATLAS 550 Manuale utente

ADTRAN

ADTRAN 1200089L2 HS Manuale utente

ADTRAN

ADTRAN NetVanta Series Manuale utente

ADTRAN

ADTRAN Total Access 324E Manuale utente

ADTRAN

ADTRAN NetVanta SHDSL Network Interface Module Manuale utente

ADTRAN

ADTRAN 1490 TX Manuale utente

ADTRAN

ADTRAN FXS+ Dual Manuale utente

ADTRAN

ADTRAN T200 HTU-R Manuale utente

ADTRAN

ADTRAN GPON 452 Manuale utente

ADTRAN

ADTRAN 1442390G1 Manuale utente

ADTRAN

ADTRAN Cable T1 ESF CSU ACE Manuale utente

ADTRAN

ADTRAN Dual T1/PRI Manuale utente

ADTRAN

ADTRAN 1200864L1 Manuale utente

ADTRAN

ADTRAN EXPRESS 6503 Manuale utente

ADTRAN

ADTRAN 1202801L1 Manuale utente

ADTRAN

ADTRAN Total Access 300 Series Manuale utente

ADTRAN

ADTRAN T200 HTU-R Manuale utente

ADTRAN

ADTRAN 17004660F1/F3 Manuale

ADTRAN

ADTRAN jobAid Manuale utente

ADTRAN

ADTRAN DUAL Nx56/64 1200142L1# Manuale utente

ADTRAN

ADTRAN 424 ONT Manuale utente

ADTRAN

ADTRAN Total Access 900 Series Manuale utente

ADTRAN

ADTRAN NetVantaE1/FE1 Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente