Advanced Microwave Products CDT1 Istruzioni operative e di manutenzione
For Technical Support, Contact AMP
at (775) 345-9933 (9 am - 5 pm PST)
or engineering@advmw.com
Advanced Microwave Products
PO Box 1437
2465 Old Highway 40 West, Suite 200
Verdi, NV 89439
Connect Antenna to SMA Connector
Connect camera/video input source to SSMA connector
Connect audio/data inputs to MDM-9S connector
(if applicable) *see reverse side
Set conguration *see reverse side
STEP
STEP
STEP
STEP
STEP
Connect power/communications inputs to the
MDM-9P connector *see reverse side
Note When setting up your system, the transmit and receive
antennas should be greater than 25 feet apart to
prevent serious damage to or destruction of the
receiver’s front end
CDT1 Transmitter Quick Start Guide
AQS-CDT1-D
Config Bandwidth Modulation FEC Guard Video (per Default) Audio Data Input Data Rate
1 8 MHz QPSK 1/2 1/4 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
2 8 MHz QPSK 2/3 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
3 8 MHz QPSK 5/6 1/16 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
4 8 MHz 16QAM 2/3 1/4 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
5 8 MHz 16QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
6 8 MHz 16QAM 5/6 1/16 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
7 8 MHz 64QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
8 8 MHz 64QAM 7/8 1/16 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
Config Bandwidth Modulation FEC Guard Video (per Default) Audio Data Input Data Rate
1 2.5 MHz QPSK 1/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
2 2.5 MHz QPSK 1/3 1/16 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
3 2.5 MHz QPSK 2/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
4 2.5 MHz QPSK 2/3 1/16 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
5 2.5 MHz 16QAM 2/3 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
6 8 MHz QPSK 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
7 8 MHz 16QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
8 8 MHz 64QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
Config Bandwidth Modulation FEC Guard Video (per Default) Audio Data Input Data Rate
1 1.25 MHz QPSK 1/3 1/8 NTSC (15 fps) or PAL (12.5 fps) 8 kHz, 16-Bit, Stereo Same as Comms 9600
2 1.25 MHz QPSK 2/3 1/16 NTSC (30 fps) or PAL (25 fps) 8 kHz, 16-Bit, Stereo Same as Comms 9600
3 2.5 MHz QPSK 1/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
4 2.5 MHz QPSK 2/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
5 2.5 MHz 16QAM 1/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
6 8 MHz QPSK 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
7 8 MHz 16QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
8 8 MHz 64QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
6/7/8 DVB-T Bandwidth
Narrowband Bandwidth
Ultra-Narrowband Bandwidth
How to Set Your Transmitter Conguration
The CDT1 Transmitter has two modes for conguring the unit: Local Mode and Remote Mode . Local Mode
utilizes 5 buttons for conguration settings and frequency selection. To change the frequency or conguration
preset, press the enter button then select the digit you want to change by using the left/right
buttons the digit will ash when selected. Use the up/down arrows to change the selected digit.
When you are done press the enter button to save and activate the settings.
The CONFIG allows you to select one of 8 conguration presets as
shown in the tables below. The CDT1 can only be programmed
when it is set to conguration“0”which is programming mode.
“PROG”is displayed on the 4, seven segment displays to the left
when in programming mode.
Line/Mic (“-10d” /”-55d”) are selectable when CONFIG is set to“L”,
RS232/TTL (“232”/”3.3”) are selectable when CONFIG is set to“d”
and Power level 1mW to 100 mW (“0”-“20”) is selectable when
CONFIG is set to“P”(for variable power transmitters).
Wiring Your CDT1 Transmitter
(Audio/Data Connections are Dependent on Conguration )
SSMA Female
Video Input
(Connect to Camera)
SMA Female
RF Output
(Connect to Antenna)
MDM-9P
Power & Programming
1:
2:
3:
4:
5:
6:
7:
8:
9:
+11 to 16 VDC Input
Ground
Ground
Ground
12 VDC Out
NC/TX Comm-
TX Comm+
RX Comm+
NC/RX Comm-
MDM-9S
Audio/Data Input
1:
2:
3:
4:
5:
6:
7:
8:
9:
Audio 1 Mic
Audio 1 Line
Ground
Audio 2 Mic
Audio 2 Line
Ground
TTL Data
RS232 Data
Ground
1 5
6 9
15
69
NC = No Connection
Indice
Altri manuali Advanced Microwave Products Trasmettitore
