Advantech ASMB-785 Manuale di installazione e funzionamento

ASMB-785 Startup Manual 1

Before you begin installing your card, please make sure that

the following items have been shipped:

• 1 ASMB-785 Startup Manual

• 1 Driver CD (user’s manual is included)

• 2 Serial ATA HDD data cables

• 2 Serial ATA HDD power cables

• 1 I/O port bracket

• 1 Warranty card

If any of these items are missing or damaged, please con-

tact your distributor or sales representative immediately.

Note: Acrobat Reader is required to view any PDF

ﬁle.Acrobat Reader can be downloaded at:

http://www.adobe.com/downloads/ (Acrobat is a

trademark of Adobe)

ASMB-785 LGA 1151 Intel Xeon E3-1200 v5/ 6th Gener-

ation Core Series ATX Server Board with DDR4, 4 PCIe,

3 PCI, 6 USB 3.0, 6 COM, 6 SATA3, Quad/Dual LANs

Startup Manual

Standard SBC Functions

• CPU: Intel LGA1151 Xeon E3-1200 v5 /Core i3/i5/i7

series processors

• BIOS: AMI 128 Mb SPI BIOS

• Chipset: Intel® C236

• System memory: Dual Channel DDR4 ECC/Non-ECC

1600/1866/2133 MHz unbuffered DIMM, Max. 64 GB

Note: Due to the inherent limitations of PC architecture,

the system may not fully detect 32 GB RAM

when 64 GB RAM is installed.

• SATA3 Interface: 6 SATA3 6Gb/s ports to support Intel

Matrix Storage with software RAID 0, 1, 10 & 5. (for

Windows only)

• Serial ports: Six serial ports, only supports RS-232

• Keyboard/Mouse connector: Supports standard PS/2

keyboard and mouse via KMBS1 pin header

• Watchdog timer: 255 level timer intervals (sec)

• USB 3.0: Supports up to Six USB 3.0 ports. Four ports

are in rear I/O, and two ports are on-board pin header.

• USB 2.0: Supports up to seven USB 2.0 ports (1* Type-A)

Display Interface

• Chipset: CPU integrated Intel HD graphics controller

• Display Memory: 1 GB maximum shared memory with 2

GB and above system memory installed

• Resolution:

- Supports RGB up to 1920 x 1200 resolution @ 60 Hz

refresh rate

- Supports DVI up to 1920 x 1200 resolution@ 60 Hz

refresh rate

Ethernet Interface

• Interface: 10/100/1000 Mbps

• Controller: LAN1:Intel

I219LM; LAN2 ~ LAN4: Intel®

I201AT

Mechanical and Environmental

• Dimensions (L x W): 244 x 304 mm (9.6” x 12”)

• Power supply voltage: +3.3 V, +5 V, ±12 V, 5 Vsb

• Power consumption: Max. load: +3.3 V @ 0.96 A, +5 V

@ 1.58 A, +12 V @ 0.32 A, +12 V (8P) @ 7.21 A, +5 Vsb

@ 0.11 A, -12 V @ 0.06 A

• Operating temperature: 0 ~ 60° C (Depends on CPU

speed and cooler solution)

• Weight: 0.75 kg (weight of board)

Specications

Packing List

For more information on this and other Advantech

products, please visit our website at:

http://www.advantech.com

For technical support and service, please visit our

support website at:

http://support.advantech.com.tw/support/new_de-

fault.aspx

This manual is for the ASMB-785 series Rev. A1

Part No. 2001S78510

Print in China

1st Edition,

November 2015

2 ASMB-785 Startup Manual

Connector list

LPC1

Low pin count connector for

Advantech TPM LPC and

RS232/485 modules.

VOLT1 Voltage Display

PMBUS1 PMBUS connector to communi-

cate with power supply

LPT1 Parallel port

AUDIO1 Audio Connector

BH2 For optional battery kit

EX_THR1 For thermometer kit

SGPIO1, SGPIO2 Serial General Purpose I/O

JFP1 Power Switch / Reset connector

JFP2 External speaker / HDD LED

connector/ SM Bus connector

JFP3

Keyboard Lock and Power LED

Suspend: Fast ﬂash (ATX/ AT)

System On: ON (ATX/ AT)

System Off: OFF (ATX/AT)

SPDIF_OUT1 SPDIF Audio output pin header

BMC1 BMC connector to support IPMI-

1000 module

Jumper list

Label Function

JCMOS1 CMOS clear

JME1 Intel ME Disable Jumper for ME/

BIOS update

JWDT1 Watch Dog Reset

JUSB1

Rear window USB2.0/3.0 port

power source switch between

+5 VSB and +5 V

JUSB2

On board USB2.0/3.0 port

power source switch between

+5 VSB and +5 V

CPUFAN_

SEL1,SYSFAN_SEL1

FAN PWM(1-2)/DC mode selec-

tion(2-3)

PSON1 AT(1-2) / ATX(2-3)

JCASE1 Case Open

JPEG1, JPEG2

PCIEX16_SLOT6 PCIe Link

swtich between one x16 or two

x8 or x8, two x4

JGREEN1 Enable/Disable deep sleep

mode

JTHR_SEL1 To select on board or external

thermometer

The board has a number of jumpers that allow you to con-

ﬁgure your system to suit your application. The table below

lists the function of each jumper and connector.

Connector list

Label Function

ATXPWR1 ATX 24 Pin main power connec-

tor (for System)

ATX12V1 Processor power connector(for

CPU)

SATA0~5 SATA III (6Gb/s)

USB7_8, USB9_10,

USB11_12 USB 2.0 Port (Header)

USB13 USB 2.0 Port (USB Type A)

USB3_4 USB 3.0 Port (Header)

PCI_SLOT1,

PCI_SLOT3,

PCI_SLOT5

PCI slot

PCIEX4_SLOT2,

PCIEX4_SLOT7 PCIe x4 slot (Gen3 x4 link)

PCIEX16_SLOT4,

PCIEX16_SLOT6

PCIE x16 slots (one Gen3 x16

link for slot 6 or two Gen3 x8

link)

DIMMA0,DIMMA1,

DIMMB0,DIMMB1 DDR4 288-pin slot

CPUFAN0 CPU FAN connector

SYSFAN0,SYSFAN1,

SYSFAN2,SYSFAN3 System FAN connector

LAN1_USB1_2,

LAN2_USB5_6

LAN1 / USB 3.0 port 1, 2 stack

connector

LAN2 / USB 3.0 port 5, 6 stack

connector

LAN3_4 LAN3 & LAN4 connector

VGA1_COM1 VGA+COM connector

DVI1_DVI2 DVI-D connector

KBMS1 External keyboard and mouse

connector(6 pin)

SPI_CN1 SPI ﬂash card pin header

LANLED1, LANLED2 LAN LED extension connector

SMBUS1 SM Bus From PCH

GPIO1 8-bit GPIO header

FPAUD1 Audio front panel header

COM2, COM3_4,

COM5_6 Serial port: RS-232

Jumpers and Connectors Jumpers and Connectors (Cont.)

ASMB-785 Startup Manual 3

JPCICLK1 PCI slot clock selection between

33 and 66 MHz

JWDT1: Watchdog timer output option

Closed Pins

Result

1-2 System reset*

2-3 NC

*: Default

PSON1: ATX, AT mode selector

Closed Pins

Result

1-2 AT Mode

2-3 ATX Mode*

*: Default

JCMOS1/JME1: CMOS clear/ME update function

Closed pins Result

1-2

Keep CMOS data/Disable ME update*

2-3 Clear CMOS data/Enable ME update

*: Default

Keep CMOS data/Disable ME update Clear CMOS data/Enable ME update

System Reset 1-2 Closed NC 2-3 Closed

1 2 3

AT Mode 1-2 closed ATX Mode 2-3 closed

1 2 3

JFP1, JFP2

Pin.3 #PWR_SW

Pin.6

GND

Pin.9 #RST_SW

Pin.12 GND

*Power button pin is located in Pin 3 & 6 of front panel

connector

The CD disc contains a driver installer program that will

lead you through the installation of various device drivers

needed to take full advantage of your motherboard.

The computer is supplied with a battery-powered realtime

clock circuit. There is a danger of explosion if battery is

incorrectly replaced. Replace only with same or equivalent

type recommended by the manufacturer. Discard used bat-

teries according to manufacturer’s instructions.

This device complies with the requirements in Part 15 of

the FCC rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired opera-

tion

3 6 9 12 PWRSW RESET

HDDLED

SNMP

JFP1

1(+) 4 7 10(-)

HDDLED

SM_BUS

SPEAKER

JFP2

PWRLED & KEYLOCK

12345JFP3

2(+) 5(-) 8 11

Jumpers and Connectors (Cont.) Installation Note

Declaration of Conformity

Software Installation

4 ASMB-785 Startup Manual

Board Layout: Jumper and Connector Locations

Board Layout

LAN3_4

VGA1_COM1

DVI1_DVI2

PMBUS1

AUDIO1

LAN1_

USB1_2

LAN2_

USB5_6

ATXPWR1

SYS

FAN0

JFP3

JCMOS1

COM2

PCIEX4_SLOT2

GPIO1

ATX12V1

EX_

THR1

FPAUD1

PCIEX16_SLOT4

PCIEX4_SLOT7

SYSFAN_

SEL1

PSON1

Intel LGA1151 Socket

DIMM A0

DIMM A1

DIMM B0

DIMM B1

SMBUS1

VOLT1

JUSB2

CPU FAN0

JTHR_SEL1

LAN LED

1 & 2

JGREEN1

JWDT1

JPEG1~3

SYS

FAN1 & 2

JFP1 + JFP2

COM3_4

JCASE1

COM5_6

SATA1~SATA5

JUSB1

Intel C236 PCH

USB3_4

KBMS1

USB7_8

USB9_10

USB11_12

SPDIF_OUT1

SYSFAN3

PCIEX16_SLOT6

JME1

SPI_CN1

CPUFAN_

SEL1

PCI_SLOT1

PCI_SLOT3

PCI_SLOT5

LPC1

LPT1

USB13

SATA0

BMC1

BH2

JPCICLK1

SGPIO1 & 2

SYS_LED1

Altri manuali per ASMB-785

Altri manuali Advantech Hardware per computer

Advantech

Advantech PCIE-1841 Manuale utente

Advantech

Advantech ACP-7000 Manuale utente

Advantech

Advantech MIC-7 Series Manuale di installazione e funzionamento

Advantech

Advantech PCIE-1730H Manuale utente

Advantech

Advantech AIMB-707 Manuale di installazione e funzionamento

Advantech

Advantech UNO-238 V2 Manuale di installazione e funzionamento

Advantech

Advantech PCA-6010 Manuale utente

Advantech

Advantech AiMC-2000 Manuale utente

Advantech

Advantech UbiQ-SM30 Manuale utente

Advantech

Advantech UNO-3300G Series Manuale utente

Advantech

Advantech PCE-5133 Manuale di installazione e funzionamento

Advantech

Advantech EPC-R6410 Manuale utente

Advantech

Advantech PCA-6742 Series Manuale di installazione e funzionamento

Advantech

Advantech ASMB-816 Series Manuale utente

Advantech

Advantech ECU-P1528PE Manuale di installazione e funzionamento

Advantech

Advantech AIMB-786 Manuale di installazione e funzionamento

Advantech

Advantech APAX-5070 Manuale utente

Advantech

Advantech PCA-6186 Manuale utente

Advantech

Advantech FWA-1211 Manuale di installazione e funzionamento

Advantech

Advantech MIO-2263 Manuale di installazione e funzionamento

Advantech

Advantech EWM-W192 Series Manuale utente

Advantech

Advantech PCA-6190 Manuale utente

Advantech

Advantech PCI-1710 Manuale utente

Advantech

Advantech RSB-3720 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente