Agilent Technologies E3633A Manuale utente

The Agilent E3633A and Agilent E3634A are high performance 200 watt single-

output dual range programmable DC power supplies with both GPIB and RS-

232 interfaces. The combination of bench-top and system features in these

power supplies provides versatile solutions for your design and test

requirements.

Convenient bench-top features

• Single-output dual range

• Easy-to-use knob control settings

• Highly visible vacuum-fluorescent display meters

• High accuracy and high resolution

• Remote voltage sensing

• Overvoltage and overcurrent protection

• Output on/off

• Excellent load and line regulation and low ripple and noise

• Operating states storage

• Portable, ruggedized case with non-skid feet

• Front and Rear output terminals

• Retrieving/Scrolling error messages on the display

Flexible system features

• GPIB (IEEE-488) and RS-232 interfaces are standard

• SCPI (Standard Commands for Programmable Instruments) compatibility

• I/O setup easily done from front-panel

• Software calibration, no internal adjustments required

Agilent E3633A and E3634A

DC Power Supplies

The Front Panel at a Glance

1 8V/20A range selection key (E3633A)

25V/7A range selection key (E3634A)

220V/10A range selection key (E3633A)

50V/4A range selection key (E3634A)

3Overvoltage protection key

4Overcurrent protection key

5Display limit key

6Recall operating state key

7 Store operating state/Local key

8Error/Calibrate key

9I/O Configuration/Secure key

10 Output On/Off key

11 Control knob

12 Resolution selection keys

13 Voltage/current adjust selection key

iii

1 8V/20A* or 25V/7A** range selection key Selects the 8V/20A or 25V/7A

range and allows the full rated output to 8V/20A or 25V/7A.

2 20V/10A* or 50V/4A** range selection key Selects the 20V/10A or

50V/4A range and allows the full rated output to 20V/10A or 50V/4A.

3 Overvoltage protection key Enables or disables the overvoltage protection

function, sets trip voltage level, and clears the overvoltage condition.

4 Overcurrent protection key Enables or disables the overcurrent protection

function, sets trip current level, and clears the overcurrent condition.

5 Display limit key Shows voltage and current limit values on the display and

allows knob adjustment for setting limit values.

6 Recall operating state key Recalls a previously stored operating state from

location ‘‘1’’, ‘‘2’’, or ‘‘3’’.

7 Store operating state / Local key1Stores an operating state in location ‘‘1’’,

‘‘2’’, or ‘‘3’’ / or returns the power supply to local mode from remote interface

mode.

8 Error / Calibrate key2Displays error codes generated during operation, self-

test and calibration / or enables calibration mode (the power supply must be

unsecured before performing calibration). See Service Guide for more details

on calibration.

9 I/O Configuration / Secure key3Configures the power supply for remote

interfaces / or secure or unsecure the power supply for calibration. See

Service Guide for more details on how to secure or unsecure the power supply.

10 Output On/Off key Enables or disables the power supply output. This key

toggles between on and off.

11 Control knob Increases or decreases the value of the blinking digit by turning

clockwise or counter clockwise.

12 Resolution selection keys Move the blinking digit to the right or left.

13 Voltage/current adjust selection key Selects the knob control function for

voltage or current adjustment.

The key can be used as the ‘‘

Local

’’ key when the power supplyis in the remote

interface mode.

You can enable the ‘‘calibration mode’’ by holding down this key when you

turn on the power supply.

You can use it as the ‘‘Secure’’ or ‘‘Unsecure’’ key when the power supply is

in the calibration mode.

*For Agilent E3633A Model **For Agilent E3634A Model

Front-Panel Voltage and Current Limit Settings

You can set the voltage and current limit values from the front panel using the

following method.

1Select the desired range using the range selection keys after turning on the

power supply.

2Press the

key to show the limit values on the display.

3Move the blinking digit to the appropriate position using the resolution

selection keys and change the blinking digit value to the desired voltage limit

by turning the control knob. If the display limit times out, press the key

again.

4Set the knob to current control mode by pressing the key.

5Move the blinking digit to the appropriate position using the resolution

selection keys and change the blinking digit value to the desired current limit

by turning the control knob.

6Press the

key to enable the output. After about 5 seconds, the display

will go to output monitoring mode automatically to display the voltage and

current at the output or the display will go to output monitoring mode

immediately by pressing the

key again.

Note All front panel keys and controls can be disabled with remote interface commands.

The Agilent E3633A and Agilent E3634A must be in "Local" mode for the front panel

keys and controls to function.

Use the voltage/current adjust selection key, the resolution selection keys,

and the control knob to change the voltage and current limit values.

Display

Limit

Display

Limit

Voltage

Current

Output

On/Off

Output

On/Off

Display Annunciators

Adrs Power supply is addressed to listen or talk over a remote interface.

Rmt Power supply is in remote interface mode.

8V Shows the 8V/20A range is selected. (Agilent E3633A model)

20V Shows the 20V/10A range is selected. (Agilent E3633A model)

25V Shows the 25V/7A range is selected. (Agilent E3634A model)

50V Shows the 50V/4A range is selected. (Agilent E3634A model)

OVP The overvoltage protection function is enabled when the

annunciator turns on or the overvoltage protection circuit has

caused the power supply to shutdown when the annunciator blinks.

OCP The overcurrent protection function is enabled when the

annunciator turns on or the overcurrent protection circuit has

caused the power supply to shutdown when the annunciator blinks.

CAL The power supply is in calibration mode.

Limit The display shows the limit values of voltage and current.

ERROR Hardware or remote interface command errors are detected and

the error bit has not been cleared.

OFF The output of the power supply is disabled (See page 52 for more

information).

Unreg The output of the power supply is unregulated (output is neither CV

nor CC).

CV The power supply is in constant voltage mode.

CC The power supply is in constant current mode.

To review the display annunciators, hold down key as you turn on

the power supply.

Display

Limit

The Rear Panel at a Glance

Use the front-panel key to:

• Select the GPIB or RS-232 interface (see chapter 3).

• Set the GPIB bus address (see chapter 3).

• Set the RS-232 baud rate and parity (see chapter 3).

1Power-line voltage setting

2Power-line fuse-holder assembly

3AC inlet

4Power-line module

5GPIB (IEEE-488) interface connector

6RS-232 interface connector

7Rear output terminals

I/O

Config

vii

In This Book

General Information

Chapter 1 contains a general description of your

power supply. This chapter also provides instructions forcheckingyour power

supply, connecting to ac power, and selecting power-line voltage.

Initial Operation

Chapter 2 ensures that thepower supply develops its rated

outputs and properly responds to operation from the front panel.

Front-Panel Operation

Chapter 3 describes in detail the use of front-panel

keys and how they are used to operate the power supply from the front panel.

This chapter also shows how to configure the power supply for the remote

interface and gives a brief introduction to the calibration features.

Remote Interface Reference

Chapter 4 contains reference information to

help you program the power supply over the remote interface. This chapter

also explains how to program for status reporting.

Error Messages

Chapter 5 lists the error messages that may appear as you

are working with the power supply. Each listing contains information to help

you diagnose and solve the problem.

Application Programs

Chapter 6 contains some remote interface

applications to help you develop programs for your application.

Tutorial

Chapter 7 describes basic operation of linear power supplies and

gives specific details on the operation and use of the Agilent E3633A and

Agilent E3634A power supplies.

Specifications

Chapter 8 lists the power supply’s specifications.

If you have questions relating to the operation of the power supply, call

1-800-829-4444 in the United States, or contact your nearest Agilent

Technologies Sales Office.

If your Agilent E3633A or Agilent E3634A fails within

e year of purchase,

Agilent will repair or replace it free of charge. Call 1-800-258-5165 ("Express

Exchange") in the United States, or contact your nearest Agilent Technologies

Sales Office.

viii

Contents

Chapter 1 General Information

Safety Considerations- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14

Safety and EMC Requirements - - - - - - - - - - - - - - - - - - - - - - - - 14

Options and Accessories - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15

Options- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15

Accessories - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15

Description - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16

Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

Initial Inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

Cooling and Location - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

Input Power Requirements- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22

Power-Line Cord - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22

Power-Line Voltage Selection- - - - - - - - - - - - - - - - - - - - - - - - - 22

Chapter 2 Initial Operation

Preliminary Checkout- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27

Power-On Checkout - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28

Output Checkout- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 29

Voltage Output Checkout - - - - - - - - - - - - - - - - - - - - - - - - - - - - 29

Current Output Checkout - - - - - - - - - - - - - - - - - - - - - - - - - - - - 30

Chapter 3 Front-Panel Operation

Front-Panel Operation Overview - - - - - - - - - - - - - - - - - - - - - - - - - 35

Constant Voltage Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 36

Constant Current Operation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 38

Storing and Recalling Operating States - - - - - - - - - - - - - - - - - - - - 40

Programming Overvoltage Protection- - - - - - - - - - - - - - - - - - - - - 42

Setting the OVP Level and Enable the OVP Circuit - - - - - - - - 42

Checking OVP Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - 43

Clearing the Overvoltage Condition - - - - - - - - - - - - - - - - - - - - 43

Programming Overcurrent Protection- - - - - - - - - - - - - - - - - - - - - 46

Setting the OCP Level and Enable the OCP Circuit- - - - - - - - 46

Checking OCP Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - 47

Clearing the Overcurrent Condition- - - - - - - - - - - - - - - - - - - - 47

Remote Voltage Sensing at the Front and Rear Terminals - - - - - 49

CV Regulation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 49

Output Rating - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 49

Output Noise - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 49

Stability - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 50

Remote Voltage Sensing Connections - - - - - - - - - - - - - - - - - - 50

Remote Voltage Sensing at the Rear Panel - - - - - - - - - - - - - - 51

Contents

Disabling the Output - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 52

Disabling the Output Using an External Relay- - - - - - - - - - - - - - - 53

Knob Locking- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 53

System-Related Operations- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 54

Self-Test - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 54

Error Conditions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 55

Display Control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 56

Firmware Revision Query - - - - - - - - - - - - - - - - - - - - - - - - - - - - 57

SCPI Language Version - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 57

Remote Interface Configuration- - - - - - - - - - - - - - - - - - - - - - - - - - 58

Remote Interface Selection - - - - - - - - - - - - - - - - - - - - - - - - - - - 58

GPIB Address- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 59

Baud Rate Selection (RS-232) - - - - - - - - - - - - - - - - - - - - - - - - - 59

Parity Selection (RS-232)- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 59

To Set the GPIB Address - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 60

To Set the Baud Rate and Parity (RS-232) - - - - - - - - - - - - - - - 61

GPIB Interface Configuration- - - - - - - - - - - - - - - - - - - - - - - - - - - - 63

RS-232 Interface Configuration- - - - - - - - - - - - - - - - - - - - - - - - - - - 64

RS-232 Configuration Overview - - - - - - - - - - - - - - - - - - - - - - - 64

RS-232 Data Frame Format - - - - - - - - - - - - - - - - - - - - - - - - - - - 64

Connection to a Computer or Terminal - - - - - - - - - - - - - - - - - 65

DTR / DSR Handshake Protocol - - - - - - - - - - - - - - - - - - - - - - - 66

RS-232 Troubleshooting- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 67

Calibration Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 68

Calibration Security- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 68

Calibration Count- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 72

Calibration Message- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 72

Chapter 4 Remote Interface Reference

SCPI Command Summary- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 75

Simplified Programming Overview- - - - - - - - - - - - - - - - - - - - - - - - 80

Using the

APPLy

Command - - - - - - - - - - - - - - - - - - - - - - - - - - 80

Using the Low-Level Commands- - - - - - - - - - - - - - - - - - - - - - - 80

Reading a Query Response - - - - - - - - - - - - - - - - - - - - - - - - - - - 81

Selecting a Trigger Source- - - - - - - - - - - - - - - - - - - - - - - - - - - - 81

Power Supply Programming Ranges- - - - - - - - - - - - - - - - - - - - 82

Using the

APPLy

Command- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 83

Output Setting and Operation Commands - - - - - - - - - - - - - - - - - - 84

Triggering Commands- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 91

Trigger Source Choices - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 91

Triggering Commands - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 93

System-Related Commands - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 94

Altri manuali per E3633A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Agilent Technologies Alimentazione elettrica

Agilent Technologies

Agilent Technologies 66309B/D Manuale utente

Agilent Technologies

Agilent Technologies 729-0800 Manuale utente

Agilent Technologies

Agilent Technologies 6571A Manuale utente

Agilent Technologies

Agilent Technologies E3610A Manuale di servizio

Agilent Technologies

Agilent Technologies 668xA Manuale utente

Agilent Technologies

Agilent Technologies E3632A Manuale utente

Agilent Technologies

Agilent Technologies 6201B Manuale utente

Agilent Technologies

Agilent Technologies 66111A Manuale utente

Agilent Technologies

Agilent Technologies E3631A Manuale utente

Agilent Technologies

Agilent Technologies 6625A Manuale utente

Agilent Technologies

Agilent Technologies 6112A Manuale utente

Agilent Technologies

Agilent Technologies E3620A Manuale di servizio

Agilent Technologies

Agilent Technologies U8030A Series Manuale utente

Agilent Technologies

Agilent Technologies E3633A Manuale utente

Agilent Technologies

Agilent Technologies E3631A Manuale utente

Agilent Technologies

Agilent Technologies 664XA Series Istruzioni operative

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Agilent Technologies

Agilent Technologies 66319B Manuale utente

Agilent Technologies

Agilent Technologies 729-0800 Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Agilent Technologies

Agilent Technologies 654xA Series Manuale utente

Agilent Technologies

Agilent Technologies AN 372-1 Istruzioni per l'installazione e il funzionamento

Agilent Technologies

Agilent Technologies 654xA Series Manuale utente

Agilent Technologies

Agilent Technologies 6443B Manuale di servizio

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente

Elmdene

Elmdene G1380xN-y-s Series Manuale utente

DTS

DTS Megashock 5 Manuale utente