Airlink101 APO1215 Manuale utente

Wireless N/A 5GHz 200mW Outdoor AP

With 15dBi Patch Antenna

Model: APO1215

Quick Installation Guide

V.1.0

1. Before You Start

9Web Browser : Internet Explorer (7.0 or above), Firefox, Safari

9A Computer with a network adapter properly installed

92 x RJ-45 Ethernet cable

Front Panel Rear Panel

1. Reboot Button : Unscrew the screw and click Reset button to restart system or reset to default configurations.

ÎPress and hold the Reset button for 2 seconds and release to restart system. The LED except Power indicator

will be off before restarting.

ÎPress and hold the Reset button for more than 10 seconds to reset the system to default configurations.

2. Power : Green LED ON indicates power on, and OFF indicates power off.

3. WLAN : Green LED FLASH indicates Wireless Transmit.

4. LAN : Green LED ON indicates connection, OFF indicates no connection, FLASH indicates packets transmit.

5. PoE Connector : For connecting to PSE.

Package Contents

• APO1215 x 1

• Quick Installation Guide x 1

• CD-ROM (with User Manual and QIG) x 1

• Power Adapter DC24V 0.5A x 1

• PoE injector x 1

• Mounting Kit x 2

Panel Function Descri

tion

stem Re

uirement

APO1215 is a multiple mode system which can be configured either as a wireless gateway or an access point

as desired. It also can be used as a WDS link for Ethernet network expansion. This section depicts different applications on

Router AP Mode, AP Mode, WDS Mode,CPE Mode, Bridge+Universal Repeater Mode and Bridge+AP Mode.

lication in Wireless Network

Router AP/WDS Mode

WDS Mode

Client Brid

e + Universal Re

eater Mode

P/WDS Mode

CPE

(

Customer Premises E

ment

)

Mode

CPE + AP Mode

APO1215

APO12

APO1215 APO1215

2. Hardware Installation

2. Connect the opposite end of the RJ-45 cable to the

P+DATA OUT port on the Power over Ethernet

Injector

3. Connect one end of another RJ-45 cable to

the DATA IN port on the Power over

Ethernet Injector

1. Connect one end of a RJ-45 cable into the

AP's PoE connector

4. Connect the opposite end of the RJ-45 cable to a

LAN port on your Switch, Router, or Computer.

5. Connect the power cord into the Power over

Ethernet Injector. Then connect the power

cord to a power outlet.

3. Configuring the Access Point

Note :

1. It is recommended that you configure the Access Point from a wired computer. Before the Access Point can be

configured, if you connect the AP to your computer directly, you must manually assign a static IP address to your

computer's network adapter in the subnet of 192.168.2.x (Refer to Section 7, How to configure TCP/IP settings on

your PC.); if you connect the AP to your Router or Switch, since the AP’s default IP address is 192.168.2.254, make

sure your Router’s IP address is 192.168.2.x and no other network devices are assigned an IP address of

192.168.2.254.

2. Disable any anti-virus and firewall programs before configuring the access point.

1. Open the web browser (Internet Explorer or Mozilla

Firefox). Enter the AP’s default IP address

“http://192.168.2.254/” and click “GO”.

2. Enter “root” for user name and “default” for

password.

3. Click Wizard.

4. Select “AP” mode and click Next button.

Note :

1. To protect your network from any unauthorized access it is recommended to enable wireless encryption.

2. The examples below are for WPA2-PSK. If you select WPA-PSK or WPA2-PSK, make sure your wireless

adapters support WPA or WPA2. If your wireless adapters do not support WPA or WPA2, then select WEP.

5. Configure the LAN settings to match your

network settings and then click Next button.

7. Enter the desired Channel/Frequency and

ESSID, then click Next button.

8. Select the desired Security Type.

9. Select the Cipher Suite(Type). For WPA2-PSK

10. Enter a Pre-shared Key and then click Finish

button. The key must be between 8and 63

ASCII or 64 HEX characters. Make sure to

copy down the encryption key.

11. Wait 35 seconds while the Access Point

reboots.

6. Configure the DNS settings to match your

network settings and then click Next button.

Your Installation is complete

For detailed information regarding the APO1215’s configuration and advanced settings, please

refer to User Manual.

4. Configuring for WDS Link

Note :

1. The system provides WDS function on Router AP Mode, AP Mode and WDS Mode.

2. WDS Link requires at least 2 APO1215X. The Two wire networks(LAN) need the same subnet.

3. The WDS Link needs to be set at same Channel and with same Security Type.

4. Please install and test in a lab environment before mounting theAPO1215.

5. After you set theAPO1215 to WDS Mode, wireless clients will not be able to connect to the APO1215.

6. The examples below are for WDS Mode.

Setting Up the Main APO1215 (Main Base Station)

1. Copy down the 12 digit MAC Address of the

Remote APO1215(Remote Base

Station). The MAC Address is on the

Overview Page (Status->Overview) and

Wireless General Setup Page(Wireless

->General Setup)

2. Follows steps 1-6 (Select “WDS” mode on

step 4) in Section 3 Configuring the Access

Point.

4. Click Enable and enter the Remote

APO1215's MAC Address.

Setting Up the Remote APO1215 (Remote Base Station)

1. Copy down the 12 digit MAC Address of the

Main APO1215 (Main Base Station).

The MACAddress is on the device label or the

Overview Page (Status->Overview) and Wireless

General Setup Page(Wireless ->General Setup)

2. Repeat steps 2-6 in Setting Up the Main

APO1215 for the Remote APO1215. Make sure

you change the IP Address of the Remote

APO1215 to be different from the Main APO1215.

4. Verify the Remote APO1215's MAC

Address and Signal Strength (RSSI)

3. Enter the desired Channel/Frequency , then

click Next button.

5. Select the desired Security Type between

WDS link, then click Finish button.

6. Wait 35 seconds while the Access Point

reboots.

3. Click Status -> WDS Status.

5. Configuring for Client Bridge

Note :

1. This section will walk you through the steps of sharing (bridging) an internet connection in one building, and extending that

same internet to another building.

2. The “Main Base Station” provide Access Point with SSID “Main_AP”

3. The Two wire networks(LAN) need the same subnet.

4. The examples below are for Client Bridge.

Setting Up the Access Point (Main Base Station)

1. Follows steps in Section 3 Configuring the

Access Point.

2. Make sure changed options as below :

•ESSID : Main_AP

•Channel : 44

•Security : WPA2-PSK

•Cihper Type : AES

•Pre-shared Ke

Setting Up the Client Bridge (Client Station)

3. Click Site Survey button. The system

will automatically scan and display the scan

results of all AP existing near by the system

4. Use Main_AP as an example here where the

AP is encrypted via WPA2-PSK/ AES security

type. Click Select button of the Main_AP,

and then click Next button.

1. Follows steps 1-6 (Select “Client Bridge”

mode on step 4) in Section 3 Configuring

the Access Point. Make sure you change

the IP address of the Client Station to be

different.

2. Configure the DHCP Serve

settings to

match your demand and then click Next

button.

Altri manuali per APO1215

Indice

Altri manuali Airlink101 Punto di accesso wireless

Airlink101

Airlink101 AP411W Manuale utente

Airlink101

Airlink101 HOMEPLUG TURBO Manuale utente

Airlink101

Airlink101 APO1010 Manuale utente

Airlink101

Airlink101 AP431W Manuale utente

Airlink101

Airlink101 APO1200 Manuale utente

Airlink101

Airlink101 AP411W Manuale utente

Airlink101

Airlink101 AP431W Manuale utente

Airlink101

Airlink101 APO1200 Manuale utente

Airlink101

Airlink101 AP671W Manuale utente

Airlink101

Airlink101 APO1010 Manuale utente

Airlink101

Airlink101 APO1000 Manuale utente

Airlink101

Airlink101 AP421W Manuale utente

Airlink101

Airlink101 AP671W Manuale utente

Airlink101

Airlink101 AP421W Manuale utente

Airlink101

Airlink101 APO1215 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente