AJA OG-Fiber Series Istruzioni operative

OG-Fiber-Series

openGear Card

Version 1.1r1

Published January 3, 2020

Installation and Operation Guide

OG-Fiber-Series openGear Card v1.1r1 2 www.aja.com

Notices

Trademarks

AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.

for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for

use with recorder, router, software and camera products. Because it matters.™ is a

trademark of AJA Video Systems, Inc. for use with camera products.

Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered trademarks of

AJA Video Systems, Inc.

AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, V2Analog™ and

V2Digital™ are trademarks of AJA Video Systems, Inc.

All other trademarks are the property of their respective owners.

this manual is subject to change without notice. No part of the document may be

reproduced or transmitted in any form, or by any means, electronic or mechanical,

including photocopying or recording, without the express written permission of AJA

Video Systems, Inc.

Contacting AJA Support

When calling for support, have all information at hand prior to calling. To contact AJA

for sales or support, use any of the following methods:

Telephone +1.530.271.3190

FAX +1.530.271.3140

Web https://www.aja.com

Support Email suppor[email protected]

Sales Email sales@aja.com

OG-Fiber-Series openGear Card v1.1r1 3 www.aja.com

Contents

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1 – OG-FIBER-Series . . . . . . . . . . . . . . . . . . . . . . . . .4

Card Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

openGear and AJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Parts Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Rear Fiber Card Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Front Fiber Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 11

OG-FIBER-TR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

OG-FIBER-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

OG-FIBER-R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

OG-FIBER-2T. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

OG-FIBER-2R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

OG-FIBER-TR-MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

OG-FIBER-T-MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

OG-FIBER-R-MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

OG-FIBER-2T-MM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

OG-FIBER-2R-MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . . 21

Warranty and Liability Information . . . . . . . . . . . . . . . . . . . . 29

Limited Warranty on Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Governing Law and Language; Your Rights . . . . . . . . . . . . . . . . . . . . . . 29

OG-Fiber-Series openGear Card v1.1r1 4 www.aja.com

Chapter 1 – OG-FIBER-Series

Card Overview

The OG-FIBER-Series cards are state-of-the-art, openGear-compatible, 3G-SDI to/

from Fiber converter cards, enabling SDI signals to be extended up to 10km over

standard Single-Mode fiber optic cable or 700 m (2296 ft) for OM4 and 300 m

(984 ft) for OM3 for Multi-Mode fiber optic cable.

Ten AJA cards are available:

• OG-FIBER TR, 1-Channel 3G-SDI/LC Single-Mode LC Fiber Transceiver

• OG-FIBER-T, 1-Channel 3G-SDI to Single-Mode LC Fiber Transmitter

• OG-FIBER-R, 1-Channel Single-Mode LC Fiber to 3G-SDI Receiver

• OG-FIBER-2T, 2-Channel 3G-SDI to Single-Mode LC Fiber Transmitter

• OG-FIBER-2R, 2-Channel Single-Mode LC Fiber to 3G-SDI Receiver

• OG-FIBER-TR-MM, 1-Channel 3G-SDI/LC Multi-Mode LC Fiber Transceiver

• OG-FIBER-T-MM, 1-Channel 3G-SDI to Multi-Mode LC Fiber Transmitter

• OG-FIBER-R-MM, 1-Channel Multi-Mode LC Fiber to 3G-SDI Receiver

• OG-FIBER-2T-MM, 2-Channel 3G-SDI to Multi-Mode LC Fiber Transmitter

• OG-FIBER-2R-MM, 2-Channel Multi-Mode LC Fiber to 3G-SDI Receiver

The inputs are re-clocked with best-in-class input jitter tolerance. The two

channel cards have completely independent paths, allowing different SDI rates to

be carried on each channel.

The fiber connector is attached to the main card for added reliability and cost

savings.

NOTE: In order to allow direct fiber connection to the card, and avoid problematic

optical couplers, AJA Fiber openGear cards have the rear connectors attached to

the front card. This means that the card cannot be removed from the frame with

the SFP module, cables, and/or BNC retaining nuts installed.

Features

• Automatic detection and re-clocking of 270Mb, 1.5Gb, and 3Gb SDI data rates

• LC Fiber connectors

• Input Present and Input SMPTE Lock LEDs

• Hot-swap capable

OG-Fiber-Series openGear Card v1.1r1 5 www.aja.com

• All SDI or ber inputs are re-clocked, and SDI inputs are also equalized.

• ASI compatible

• Compatible with DFR-8321 and OG3 openGear frames

• Five-year international warranty with unlimited technical support

NOTE: OG-FIBER-Series cards do not communicate with the DashBoard Control System.

Block Diagram

3G-SDI

Identical

Second Output

Optical

Fiber

Input

3G-SDI

Output

OG-FIBER-R, OG-FIBER-R-MM

Optical

Receiver Equalize &

Reclock

Optical

Fiber

Out

3G-SDI

Input

3G-SDI Re-clocked

Loop Thru Output

OG-FIBER-T, OG-FIBER-T-MM

Equalize &

Reclock Optical

Transmitter

Optical

Fiber

Out

3G-SDI

Input

Optical

Fiber

Input

3G-SDI

Output

OG-FIBER-TR and OG-FIBER-TR-MM

Optical

Receiver Equalize &

Reclock

Equalize &

Reclock Optical

Transmitter

Optical

Fiber

Input 1

3G-SDI

Output 1

Optical

Fiber

Input 2

3G-SDI

Output 2

OG-FIBER-2R and OG-FIBER-2R-MM

Optical

Receiver Equalize &

Reclock

Optical

Receiver Equalize &

Reclock

Optical

Fiber

Out 1

3G-SDI

Input 1

Optical

Fiber

Out 2

3G-SDI

Input 2

OG-FIBER-2T and OG-FIBER-2T-MM

Equalize &

Reclock Optical

Transmitter

Equalize &

Reclock Optical

Transmitter

OG-Fiber-Series openGear Card v1.1r1 6 www.aja.com

Connectors

Figure 1. Rear View of Empty Rear Card and Installed Dual Channel Fiber Cards

Output

BNC 1

(J1)

Input

Fiber 1

Input

Fiber 2

Output

BNC 2

(J2)

OG-FIBER-2R

Card Installed

Input

BNC 1

(J1)

Output

Fiber 2

Output

Fiber 1

Input

BNC 2

(J2)

OG-FIBER-2T

Card Installed

Output

BNC

(J1)

Input

Fiber

Output

Fiber

Input

BNC

(J2)

OG-FIBER-TR

Card Installed

OG-FIBER-Rear

Card

Seating tab to be inserted into frame seating slot.

NOTE: On the OG-Fiber-2T card, Output Fiber 2 is located above Output Fiber 1.

Figure 2. Rear View of Empty Rear Card and Installed Single Channel Fiber

Cards

Output

BNC 1

(J1)

Input

Fiber

Output

BNC 2

(J2)

OG-FIBER-R

Card Installed

Input

BNC

(J1)

Output

Fiber

Output

Loop

BNC

(J2)

OG-FIBER-T

Card Installed

OG-FIBER-Rear

Card

Seating tab to be inserted into frame seating slot.

Indicators

LEDs on the front (near door) of each card indicate, from top to bottom:

2T and 2R Cards

• DC power detected (green)

• Input 1 signal present (green)

• Input 1 SMPTE locked (green)

• Input 2 signal present (green)

• Input 2 SMPTE locked (green)

TR Cards

• DC power detected (green)

• Optical input signal present (green)

• Optical input SMPTE locked (green)

• SDI input signal present (green)

OG-Fiber-Series openGear Card v1.1r1 7 www.aja.com

• SDI input SMPTE locked (green)

Single Channel Cards

• DC power detected (green)

• Signal present (green)

• SMPTE locked (green)

openGear and AJA

openGear is an open-architecture, modular frame system designed by Ross

Video and supported by a diverse range of terminal equipment manufacturers,

including AJA. Ross Video manufactures the frames, power supplies and network

cards for openGear.

AJA Video is a leading manufacturer of video interface technologies, converters,

digital video recording solutions and professional cameras, bringing high-

quality, cost-effective products to the professional, broadcast and post-

production markets. AJA products, including openGear cards, are designed and

manufactured at our facilities in Grass Valley, California.

Parts Supplied

Each OG-FIBER card is shipped with:

• OG-FIBER card in an ESD bag

• Fiber Rear Card

• SFP module in ESD bag

• BNC nuts and star washers

Installation

CLASS 1

LASER

PRODUCT

Warning! Active ber-optic cables emit radiation invisible to the human eye. Do

not look directly at the end of an active ber-optic cable or the ber connector

on an OG-FIBER-2T, OG-FIBER-2T-MM, OG-FIBER-TR, OG-FIBER-TR-MM, OG-

FIBER-T, OG-FIBER-T-MM; these models are Class 1 Laser Products.

Summary

Installing an OG-FIBER card into a DFR-8321 or OG3 openGear frame consists of

the following steps:

1. Install a Rear Fiber Card into the frame.

2. Ensure the SFP module is removed from the Front Fiber Card.

3. Insert the Front Fiber card in the left (odd numbered) slot of the pair.

4. Install BNC connector retaining nuts and washers.

5. Insert the SFP module into the card from the rear of the frame.

6. Connect the BNC and Fiber cabling.

OG-Fiber-Series openGear Card v1.1r1 8 www.aja.com

ESD Susceptibility - Static discharge can cause serious damage to sensitive

semiconductor devices. Avoid handling circuit boards in high static

environments such as carpeted areas, and when wearing synthetic ber clothing.

Always exercise proper grounding precautions when working on circuit boards

and related equipment.

Unpacking

Unpack each openGear product you received from the shipping container and

ensure that all items are included. If any items are missing or damaged, contact

your sales representative or AJA directly.

Rear Fiber Card Installation

1. Power down the openGear frame.

2. Ensure that the frame is properly installed.

3. Locate the card frame slot on the rear of the openGear frame into which you

wish to install the openGear card.

NOTE: An OG-FIBER card occupies two slots in the frame.

4. Using a Phillips screwdriver, unscrew the top screw from the desired blank

rear plate and remove the rear plate.

5. Seat the bottom of the Rear Card in the seating slot at the base of the frame

back plane (Figure 3).

Figure 3. Rear Card Inserted Into Frame Seating Slot

6. Align the top screw of the Rear Card with the screw hole on the top edge of

the frame back plane.

7. Ensure the Rear Card aligns with the desired card slot before tightening the

screw.

8. Using a Phillips screwdriver, fasten the Rear Card to the frame back plane.

Do not over tighten.

9. Ensure proper frame cooling and ventilation by having all rear frame slots

covered with rear modules or blank metal plates if plates are not pre-

installed.

Front Fiber Card Installation

Caution! The SFP module must be removed from an OG-FIBER card before

inserting the card into or removing the card from an openGear frame.

1. If necessary, remove the SFP module from the Front Card by lifting the lever

and pulling out the module.

OG-Fiber-Series openGear Card v1.1r1 9 www.aja.com

2. If nuts and washers are pre-installed on the BNC connectors, they must be

removed before inserting the card in the frame.

3. Open the openGear frame door as follows:

A. Gently pull the side door tabs towards the center of the door, releasing the

door from the frame.

B. Using both hands, pull the door towards you. The door extender arms

prevent the door from falling.

4. Locate the Rear Card you installed as described above. The interior slot

number is dependent on the slot combinations into which you installed the

Rear Card. This allows adequate spacing to avoid damaging the card, the

cards installed in the neighboring slots, or both.

5. Hold the card by the edges and carefully align the card edges with the rails

inside the frame. The slots are numbered starting from the left-most slot

when facing the fame front.

NOTE: OG-FIBER cards are installed into the left (odd numbered) slot of the pair.

6. Fully insert the card into the frame until the card is properly seated in the

Rear Card. (Figure 4).

Figure 4. OG-FIBER Card Inserted Into Left Slot

7. Secure the card in the frame by the BNC connectors using the star washers

and nuts provided (Figure 5).

Figure 5. BNC Star Washer and Nut Installation

8. Insert the SFP ber module into the socket until it clicks and locks. The lever

handle is on the left (Figure 6).

OG-Fiber-Series openGear Card v1.1r1 10 www.aja.com

Figure 6. Fiber SFP Installation

NOTE: The SFP module must match the card’s capabilities for proper operation. Input

and output triangles next to the fiber ports identify which are inputs and which

are outputs.

Figure 7. An SFP Module

9. Close the frame door as follows:

A. Slide the door into the frame.

B. Pull and release the door tabs to ensure the frame door is securely locked

to the frame.

Cabling

Refer to Figure 1 on page 6 and Figure 2 on page 6 to identify the input and

output signal connectors.

NOTE: Keep the protective rubber plug in the SFP module until the fiber cabling is

actually connected to the module.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali AJA Trasmettitore

AJA

AJA Dante AV 4K Series Istruzioni operative

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente