Alaris Passport Flatbed Accessory Manuale utente
Passport Flatbed Accessory
A-61882
User’s Guide
A-61882 December 2018 i
Safety
User precautions
• Only use the scanner and power supply indoors in a dry location.
• Make sure the electrical power outlet is located within 1.52 meters (5 feet) of the scanner and is easily accessible.
• Do not damage, knot, cut or modify the power cord.
• Use only the AC adapter that is supplied with the E1000, S2000 or S2000w scanner. Be sure the power cord is securely
plugged into the wall outlet.
• Do not plug the power cord from the Passport Flatbed Accessory into any other device than an Alaris E1000, S2000 or
S2000w scanner.
• Leave sufficient space around the power outlet so the scanner can be easily unplugged in case of an emergency.
• Do not use the scanner if it becomes inordinately hot, has a strange odor, emits smoke, or makes unfamiliar noises.
Immediately stop the scanner and disconnect the power cord from the power outlet. Contact Alaris Service.
• Do not disassemble or modify the scanner or the AC power adapter.
• Follow the Alaris recommended cleaning procedures. Do not use air, liquid or gas spray cleaners. These cleaners displace
dust, dirt and debris to another location within the scanner, which may cause the scanner to malfunction.
Environmental information
• The Alaris Passport Flatbed Scanner Accessory is designed to meet worldwide environmental requirements.
• Guidelines are available for the disposal of consumable items that are replaced during maintenance or service;
follow local regulations or contact Kodak Alaris locally for more information.
• Disposal of this material may be regulated due to environmental considerations. For recycling or reuse
information, contact your local authorities, or in the USA, go to:
www.AlarisWorld.com/go/scannerrecycling.
• The product packaging is recyclable.
• Parts are designed for reuse or recycling.
• Safety Data Sheets (SDS) for chemical products are available on the Kodak Alaris website at:
www.AlarisWorld.com/go/ehs. When accessing the SDS from the website, you will be required to provide the
catalog number of the consumable.
European Union
This symbol indicates that when the last user wishes to discard this product, it must be sent to
appropriate facilities for recovery and recycling. Please contact your local Kodak Alaris representative
or refer to www.AlarisWorld.com/go/scannerrecycling for additional information on the collection and
recovery programs available for this product.
Please consult www.AlarisWorld.com/go/REACH for information about the presence of substances included
on the candidate list according to article 59(1) of Regulation (EC) No. 1907/2006 (REACH).
Acoustic emission
Maschinenlärminformationsverordnung – 3, GSGV
Der arbeitsplatzbezogene Emissionswert beträgt <70 db(A).
[Machine Noise Information Ordinance — 3, GSGV
The operator-position noise emission value is <70 dB(A).]
ii A-61882 December 2018
EMC statements
United States: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for additional suggestions.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment. Where shielded interface cables have been provided with the product or specified additional
components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to
ensure compliance with FCC regulation.
Korea: As this equipment has obtained EMC registration for household use, it can be used in an area including residential
areas.
Japan: This is a Class B product based on the standard of the Voluntary Control Council for interference by information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio
interference. Install and use the equipment according to the instruction manual.
A-61882 December 2018 1
Using the Alaris Passport Flatbed Accessory
Contents Connecting the flatbed to an E1000 Series Scanner ......................... 2
Connecting the flatbed to an S2000 Series Scanner ......................... 4
Flatbed scanning (E1000 Series)....................................................... 6
Flatbed scanning (S2000 Series........................................................ 8
Using manual cropping modes (E1000 and S2000 Series) ............. 10
Cleaning the flatbed (E1000 and S2000 Series).............................. 11
Indicator light (E1000 and S2000 Series) ........................................ 11
The Alaris Passport Flatbed Accessory is designed to make it quick and
easy to scan a passport or other similar sized documents. The cables
included with the Passport Flatbed Accessory connect your flatbed so
that it operates with an E1000, S2000 or S2000w Scanner to provide
images to your computer.
NOTES:
• Terminology usage within this document:
“Scanner” refers to an Alaris E1000, S2000 or S2000w Scanner;
“Flatbed” refers to the Alaris Passport Flatbed Accessory.
• The Passport Flatbed Accessory must be used with an Alaris E1000,
S2000 or S2000w Scanner; it cannot be used as a standalone
device, or with any other scanner.
Specifications for the Alaris Passport Flatbed Accessory are available
on the Accessories page for your scanner (look in Brochures):
www.AlarisWorld.com/go/S2000
www.AlarisWorld.com/go/S2000w
www.AlarisWorld.com/go/E1025
www.AlarisWorld.com/go/E1035
2A-61882 December 2018
Using the Alaris Passport Flatbed Accessory
Connecting the
flatbed to an E1000
Series Scanner
The Installation Guide in the box with your flatbed shows how to
connect the flatbed to the scanner and your PC.
1. Power down the scanner. Unplug the scanner power cord from the
wall and from the scanner.
2. Place the flatbed on a table or desk. Place the scanner on the
flatbed as shown below.
3. Take the short power cord that comes out of the flatbed, and
connect it from the flatbed to the scanner, as shown below.
4. Remove the long USB cable from the flatbed box. Use it to connect
from the flatbed to the computer, as shown below. Use the USB
cable that came with your scanner to connect the scanner to the
computer.
A-61882 December 2018 3
Using the Alaris Passport Flatbed Accessory
5. Take the power cord that you removed from the scanner. Connect it
to the flatbed, then plug it into the wall outlet.
6. Turning on the computer will power up the flatbed.
NOTE: The flatbed will automatically calibrate when it powers up.
During calibration, the flatbed motor will run and the lamps/
LEDs will be illuminated.
7. The flatbed power indicator light will be illuminated if the flatbed is
connected to the computer and the computer is powered on.
NOTE: If you need to disconnect the power cable from the scanner or
flatbed; turn off the scanner first, then disconnect the USB cable
from the flatbed, then disconnect the power cable from the wall
outlet.
4A-61882 December 2018
Using the Alaris Passport Flatbed Accessory
Connecting the
flatbed to an S2000
Series Scanner
The Installation Guide in the box with your flatbed shows how to
connect the flatbed to the scanner and your PC.
1. Power down the scanner. Unplug the scanner power cord from the
wall and from the scanner.
2. Place the flatbed on a table or desk. Place the scanner on the
flatbed as shown below.
3. Take the short power cord that comes out of the flatbed, and
connect it from the flatbed to the scanner, as shown below.
4. Remove the short USB cable from the flatbed box. Use it to connect
from the flatbed to the scanner, as shown below. Use the USB 2.0
port for this connection, not the USB SuperSpeed port.
A-61882 December 2018 5
Using the Alaris Passport Flatbed Accessory
NOTES on the above illustration:
- Your scanner may also have a USB cable from the other USB
port to your PC.
- Your scanner may also have an Ethernet cable from the scanner
to the wall.
5. Take the power cord that you removed from the scanner. Connect it
to the flatbed, then plug it into the wall outlet.
6. Turn on the scanner. Turning on the scanner will also power up the
flatbed.
NOTE: The flatbed will automatically calibrate when it powers up.
During calibration, the flatbed motor will run and the lamps/
LEDs will be illuminated. You can also request a calibration
from the menu on the scanner screen.
7. The flatbed power indicator light will blink when the flatbed is being
powered up. The light will become steady when the flatbed is ready
to be used.
NOTE: If you need to disconnect the power cable from the scanner or
flatbed, turn off the scanner first, then disconnect the cable.
6A-61882 December 2018
Using the Alaris Passport Flatbed Accessory
Flatbed scanning
(E1000 Series)
Passports Use the flatbed to scan passport documents that cannot be fed through
the scanner. You can scan passports in two ways; by scanning just one
page at a time, or by scanning two pages at the same time. Either way,
to scan a passport:
1. On the TWAIN driver profile settings screen, set Paper source to
Automatic. If there is no paper in the scanner input tray, the
application will expect to scan at the flatbed.
For an ISIS application: review the ISIS help file for system
configuration.
2. Choose the scanning profile or task to use in your application.
3. Remove all pages from the input tray of the scanner.
4. Place the passport face down on the glass platen. You can scan
two pages or one. The left illustration shows scanning two pages;
the right shows scanning one page. For either case, the passport
should touch both the far edge and the right edge of the platen.
Keep your hand on the passport for best results.
5. Select the Play/Scan/Start icon in your scanning application.
Smaller documents Use the flatbed to scan other types of small documents that cannot be
fed through the scanner.
1. On the TWAIN driver settings screen, set Paper source to
Automatic. If there is no paper in the scanner input tray, the
application will expect to scan at the flatbed.
For an ISIS application: review the ISIS help file for system
configuration.
2. Choose the scanning profile or task to use in your application.
3. Remove pages from the scanner input tray.
4. Place the small document on the flatbed platen.
5. Select the Play/Scan/Start icon in your scanning application.
Indice
Altri manuali Alaris Scanner
