Alcatel-Lucent OAW-AP228 Manuale utente

OAW-AP228 Wireless Access Point

Installation Guide

0511756-01 | January 2015 1

The Alcatel-Lucent OAW-AP228 is a fully temperature hardened, water resistant, indoor rated, dual-

radio IEEE 802.11ac wireless access point. This access point use MIMO (Multiple-in, Multiple-out)

technology and other high-throughput mode techniques to deliver high-performance, 802.11ac

2.4 GHz and 5 GHz functionality while simultaneously supporting existing 802.11a/b/g/n wireless

services. The OAW-AP228 access point works only in conjunction with an Alcatel-Lucent Switch.

OAW-AP228 Operations

Wireless transceiver

Wireless access point (IEEE 802.11 a/b/g/n/ac)

Wireless air monitor (IEEE 802.11 a/b/g/n/ac)

Protocol-independent networking functionalityF

Compatibility with IEEE 802.3at PoE

Central management configuration and upgrades with an Alcatel-Lucent Switch.

Guide Overview

“OAW-AP228 Hardware Overview” on page3provides a detailed hardware overview of the

OAW-AP228.

“Before You Begin” on page5provides key questions to ask and items to consider when deploying

a wireless network.

“Installing the AP” on page7describes the multi-step process for a successful installation and

deployment of the OAW-AP228.

“Safety and Regulatory Compliance” on page12 provides an overview of safety and regulatory

compliance information.

Package Contents

OAW-AP228 Access Point

Cable Glands x2

USB Console Cable

Copper Lug x1

M4 x 6 Screw x1

Installation Guide (this document)

The weatherproof caps for Ethernet and Console interfaces are connected to the AP, not loose in the package.

Mounting kits for use with the OAW-AP228 access points are sold separately. Contact your Alcatel-Lucent sales

representative for details.

2OAW-AP228 Wireless Access Point | Installation Guide

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton,

including the original packing materials. Use these materials to repack and return the unit to the supplier if

needed.

OAW-AP228 Wireless Access Point | Installation Guide 3

OAW-AP228 Hardware Overview

Figure 1 OAW-AP228 Front View

Figure 2 OAW-AP228 Bottom View

LED

The OAW-AP228 is equipped with one LED that indicates the system status of the AP.

Table 1 OAW-AP228 LED Meanings during Boot Up

LED Color/State Meaning

System LED Off No power to AP

Red Initial power-up

Green - Flashing AP booting

Green - Steady AP ready and 1000Mbps Ethernet link established. The LED

turns off after 1200 seconds

Green - Yellow, 6 seconds

period AP ready and 10/100Mbps Ethernet link established. The LED

turns off after 1200 seconds

2G0

2G1

2G2

5G0

5G1

5G2

LAN

WAN

Grounding Point

USB Console Port, Reset button and LED

4OAW-AP228 Wireless Access Point | Installation Guide

Table 2 OAW-AP228 LED Meanings during Operation

USB Console Port

The USB Micro-B console port allows you to connect the AP to a terminal or a laptop for direct local

management. Use the included USB console cable to connect the AP. You can download the

necessary driver for USB-UART adapter from https://service.esd.alcatel-lucent.com.

Use the following setting to access the terminal:

Ethernet Ports

OAW-AP228 is equipped with two10/100/1000Base-T (RJ-45) Gigabit Ethernet ports (WAN and LAN

port) for wired network connectivity. The WAN port supports 802.3at Power over Ethernet (PoE),

accepting 48 VDC (nominal) as a standard defined Powered Device (PD) from a Power Sourcing

Equipment (PSE) such as a PoE midspan injector.

These ports have RJ-45 female connectors with the pin-outs shown in Figure 3.

Figure 3 Gigabit Ethernet Port Pin-Out

Reset Button

The reset button can be used to return the AP to factory default settings. To reset the AP:

1. Power off the AP.

2. Press and hold the reset button using a small, narrow object, such as a paperclip.

3. Power-on the AP without releasing the reset button. The system LED will flash within 5 seconds.

4. Release the reset button.

The system LED will flash again within 15 seconds indicating that the reset is completed. The AP will

now continue to boot with the factory default settings.

LED Color/State Meaning

System LED Solid Red General fault

One blink off every 3

seconds Radio 0 fault (5 GHz)

Two quick blink off 0.5

seconds apart cycled every

3 seconds

Radio 1 fault (2.4GHz)

Table 3 Console Settings

Baud Rate Data Bits Parity Stop Bits Flow Control

9600 8 None 1 None

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C, POE Positive

Bi-directional pair -C, POE Positive

Bi-directional pair +D, POE Negative

Bi-directional pair -D, POE Negative

Bi-directional pair +A, POE Negative

Bi-directional pair -A, POE Negative

Bi-directional pair +B, POE Positive

Bi-directional pair -B, POE Positive

OAW-AP228 Wireless Access Point | Installation Guide 5

Grounding Point

Always remember to protect the AP by installing grounding lines. The ground connection must be

complete before connecting power to the AP enclosure.

Figure 4 OAW-AP228 Rear View

Before You Begin

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their placement have been

determined, the Alcatel-Lucent switch(s) must be installed and initial setup performed before the

Alcatel-Lucent APs are deployed.

CAUTION

FCC Statement: Improper termination of access points installed in the United States configured to non-US

model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or

intentional violation may result in a requirement by the FCC for immediate termination of operation and may

be subject to forfeiture (47 CFR 1.80).

CAUTION

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the AOS-W User Guide

for details on restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous

referrer au AOS-W User Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich

Einschränkungen finden Sie im AOS-W User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla AOS-W User Guide per

avere informazioni detagliate sulle restrizioni.

CAUTION

To meet regulatory restrictions, the access point must be professionally installed.

6OAW-AP228 Wireless Access Point | Installation Guide

For initial setup of the switch, refer to the AOS-W Quick Start Guide for the software version installed

on your switch.

Pre-Installation Checklist

Before installing your AP, be sure that you have the items listed below:

Gigabit Ethernet cable of required length

IEEE 802.3at compliant PoE source

Alcatel-Lucent Mobility Controller configured and installed on the network

Layer 2/3 network connectivity to your AP

One of the following network services:

Alcatel-Lucent Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor specific options

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs will be able to locate and

connect to the switch when they are powered on.

Specifically, you must verify the following conditions:

When connected to the network, each AP is assigned a valid IP address.

APs can locate the switch.

Refer to the AOS-W Quick Start Guide for instructions on locating and connecting to the switch.

Identifying Specific Installation Locations

Use the AP placement map generated by Alcatel-Lucent’s RF Plan software application to determine

the proper installation location(s). Each location should be as close as possible to the center of the

intended coverage area and should be free from obstructions or obvious sources of interference.

These RF absorbers/reflectors/interference sources will impact RF propagation and should have been

accounted for during the planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the

installation phase is critical. Make sure that these sources are taken into consideration when you

attach an AP to its fixed location. Examples of sources that degrade RF performance include:

Cement and brick

Objects that contain water

Alcatel-Lucent, Inc. in compliance with governmental requirements, has designed the OAW-AP228 such that

only authorized network administrators can change configuration settings. For more information about AP

configuration, refer to the AOS-W Quick Start Guide and AOS-W User Guide.

CAUTION

Access points are radio transmission devices and as such are subject to governmental regulation. Network

administrators responsible for the configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in

which the access point will be used.

OAW-AP228 Wireless Access Point | Installation Guide 7

Metal

Microwave ovens

Wireless phones and headsets

Installing the AP

Using the AP-220-MNT-W1 Mount Kit

The OAW-AP228 access point can be installed on a wall by using AP-220-MNT-W1 mount kit.

1. Begin by attaching the wall mount adapter to the wall.

a. Install any necessary wall anchors. Wall anchors are not included in this kit.

b. Align the screw holes in the mounting bracket with the previously installed anchors or

demarcated screw points.

c. Insert the screws to secure the mounting bracket. Screws are not included in this kit.

Service to all Alcatel-Lucent products should be performed by trained service personnel only.

The OAW-AP228 access point does not ship with any mount kit. The AP-220-MNT-W1 mount kit is available as

accessories and must be ordered separately.

For details on AP-220-MNT-W1, please refer to the AP-220-MNT-W1 Installation Guide.

8OAW-AP228 Wireless Access Point | Installation Guide

Figure 5 Attaching the Adapter to a Wall

Figure 6 Attaching the Adapter to a Wall (Alternate)

2. Attach necessary cables and/or antennas to the AP.

3. Attach the AP to the secured mounting adapter as shown in Figure 7.

a. Align the AP with a mounting adapter, placing the AP so that it’s mounting tabs are at an angle

of approximately 30 degrees to the adapter.

4. Pushing toward the wall, rotate the AP clockwise until it clicks into place (see Figure 7).

AP-220_11

AP-220_14

OAW-AP228 Wireless Access Point | Installation Guide 9

Figure 7 Attaching the AP to the Mounting Bracket

Figure 8 Completed Installation

Grounding the AP

The grounding must be completed before powering up the AP. The grounding wire should be #8

AWG.

1. Peel the cover of one end of the grounding wire and place the bare grounding wire into the

included copper lug, and press firmly with the crimping pliers.

2. Fasten the copper lug to the grounding hole on the AP with the included M4 x6 screw.

Connecting the Ethernet Cable

To connect the Ethernet cable to the AP, perform the following steps using the cable glands that ships

with your AP.

WARNING

Failure to use the included Ethernet cable glands can lead to connectivity and POE issues.

10 OAW-AP228 Wireless Access Point | Installation Guide

Figure 9 Installing a Cable Gland

1. Slide the sealing nut over the cable (without the RJ45 connector attached to the end).

2. Slide the clamping ring over the cable.

3. Using a crimping tool, attach the shielded RJ45 connector to the end of the cable.

4. Remove the weatherproof cap on the Ethernet port.

5. Insert the RJ45 connector to the Ethernet port.

6. Screw the clamping ring onto the Ethernet port.

7. Screw the sealing nut onto the clamping ring.

Verifying Post-Installation Connectivity

The integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing

successfully (see Table 1 and Table 2). Refer to the AOS-W Quick Start Guide for further details on

verifying post-installation network connectivity.

Configuring the AP

AP Provisioning/Reprovisioning

Provisioning parameters are unique to each AP. These local AP parameters are initially configured on

the switch which are then pushed out to the AP and stored on the AP itself. Alcatel-Lucent

recommends that provisioning settings be configured via the AOS-W Web UI only. Refer to the AOS-W

User Guide for complete details.

AP Configuration

Configuration parameters are network or switch specific and are configured and stored on the

switch. Network configuration settings are pushed out to the AP(s) but remain stored on the switch.

Configuration settings can be configured via the AOS-W Web UI or AOS-W CLI. Refer to the AOS-W

User Guide for complete details.

The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated,

CAT 5E or better RJ45 cable for use with the AP.

Sealing Nut Clamping Ring CAT 5E or Better Cable

Seals

The seals inside the clamping ring by factory default is applicable for cables with 5-8.5 mm diameter. In the

cable gland kit, another seals is provided for use with the cables with 7-10 mm diameter.

Indice

Altri manuali Alcatel-Lucent Punto di accesso wireless

Alcatel-Lucent

Alcatel-Lucent OmniAccess 700 CLI Manuale operativo

Alcatel-Lucent

Alcatel-Lucent 9962 Manuale

Alcatel-Lucent

Alcatel-Lucent OmniAccess AP 70 Manuale utente

Alcatel-Lucent

Alcatel-Lucent OAW-AP204 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 9764 Series Manuale di istruzioni

Alcatel-Lucent

Alcatel-Lucent OAW-AP277 Manuale utente

Alcatel-Lucent

Alcatel-Lucent OmniAccess AP60 Manuale utente

Alcatel-Lucent

Alcatel-Lucent OAW-IAP224 Manuale utente

Alcatel-Lucent

Alcatel-Lucent OAW-RAP155 Manuale utente

Alcatel-Lucent

Alcatel-Lucent AOS-W Instant Manuale utente

Alcatel-Lucent

Alcatel-Lucent 4080 IP-DECT Manuale utente

Alcatel-Lucent

Alcatel-Lucent 9763 Manuale di istruzioni

Alcatel-Lucent

Alcatel-Lucent OAW-AP224 Istruzioni operative e di manutenzione

Alcatel-Lucent

Alcatel-Lucent AP-120 Series Manuale utente

Alcatel-Lucent

Alcatel-Lucent OAW 320 Series Manuale utente

Alcatel-Lucent

Alcatel-Lucent OmniAccess AP92 Manuale utente

Alcatel-Lucent

Alcatel-Lucent OAW-AP210 Series Manuale utente

Alcatel-Lucent

Alcatel-Lucent OAW-AP120 Series Manuale utente

Alcatel-Lucent

Alcatel-Lucent OmniAccess OAW-AP41 Manuale utente

Alcatel-Lucent

Alcatel-Lucent OmniAccess 700 Manuale utente

Alcatel-Lucent

Alcatel-Lucent Stellar AP Series Manuale utente

Alcatel-Lucent

Alcatel-Lucent OmniAccess AP80 Manuale utente

Alcatel-Lucent

Alcatel-Lucent AP1320 Series Manuale utente

Alcatel-Lucent

Alcatel-Lucent AOS-W 3.4 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente