Alcatel Y901NB Manuale utente

Y901NB

User Manual

www.sar-tick.com

This product meets applicable national SAR limits of 2.0W/kg.

The specic maximum SAR values can be found in the section of this

user guide.

When carrying the product or using it while worn on your body, either

use an approved accessory such as a holster or otherwise maintain

a distance of 15 mm from the body to ensure compliance with RF

exposure requirements. Note that the product may be transmitting

even if you are not Surng Internet.

Safety Precautions

Read the safety precautions carefully to ensure the correct and safe use of your wireless

device.

Do not switch on your device when the device use is prohibited or when the

device use may cause interference or danger.

Follow the rules or regulations in hospitals and health care facilities. Switch off your device

near medical apparatus.

Switch off your device in an aircraft.The device may cause interference to control signals of

the aircraft.

Switch off your device near high-precision electronic devices. The device may affect the

performance of these devices.

Do not attempt to disassemble your device or its accessories. Only qualied personnel are

allowed to service or repair the device.

Do not place your device or its accessories in containers with strong electromagnetic eld.

Do not place magnetic storage media near your device. Radiation from the device may erase

the information stored on them.

Do not put your device in a high-temperature place or use it in a place with ammable gas

such as a gas station.

Keep your device and its accessories away from children. Do not allow children to use your

device without guidance.

Use approved batteries and chargers only to avoid explosion.

Observe the laws or regulations on device use. Respect others’ privacy and legal rights

when using your device.

It is recommended that the equipment only be used in the environment where temperature

is between -10°C and 45°C and humidity is between 10% to 93%. Keep the equipment in the

environment where temperature is between -10°C and 70°C or humidity is between 5% to

95%.

CHARGERS

Mains powered chargers will operate within the temperature range of: 0°C to 40°C.

The chargers designed for your device meet with the standard for safety of information

technology equipment and ofce equipment use.

They are also compliant to the ecodesign directive 2009/125/EC. Due to different applicable

electrical specications, a charger you purchased in one jurisdiction may not work in another

jurisdiction. They should be used for this purpose only.

The charger shall be installed near the equipment and shall be easily accessible. Adapter shall

be installed near the equipment and shall be easily accessible.

1. Web UI conguration

1.1 login the conguration page

Open the browser, and then input the address http://192.168.1.1.

The default login password is admin.

1.2 Icon description

The icon description as bellow:

Category Icon Display

Signal Strength

From no signal to excellent

Network Status Disconnect, Connected, Roaming

SMS Normal, New message, SMS box full, View Message

Home click to go back to Home page

Battery Battery Level

Network Type

2G: EDGE, GPRS;

3G: HSPA, HSUPA, UMTS;

3G+: HSPA+, DC-HSPA+;

4G: LTE

Connection

Status Connected, Disconnected

Usage Usage Data

Wi-Fi status Wi active with connected Devices

Tab 2.1

2. Connection

Click “Connection” area to open connection menu, including connection info, upload/

download usage (for a connected duration), network technology, battery status, number of

device connected are included.

2.1 Connection Information

¾Turn on/off Key: connect/disconnect from internet;

¾Network information: display Operator name, if network is roaming, the icon “R” appeared

on right of operator name, otherwise, hidden “R” icon;

2.2 Usage Information

A current usage time and data is displayed

¾Total time duration for current connection in HH:MM (e.g: 12Hr 02 Min);

¾Total data for current connection in MB or GB;

2.3 Signal & Technology Info

¾Signal icon: Shows the signal strength, Icon is grey if no service;

¾Network technology: 2G, 3G, 3G+, 4G in different network; Icon is empty in

disconnected and no service status;

2.4 Battery information

¾Lower power

¾Different battery level

2.5 Connected devices information

This component shows the connected devices to this device.

¾Device list edit: click “numbers” to view detail connected devices. Click to edit the

device name, and to save the changes, click any other area to give up the changes;

¾Block list edit: click “Block” or “unblock” to manage device list, but USB Device cannot be

blocked

3. Usage

Click “Usage” area to open usage status menu, display usage info in home and roaming status,

including upload/download data transfers.

3.1 Usage information

¾Home: local download + upload usage, current Volume/total Volume; Clear all data when

start a new period cycle;

¾Roaming: current Roaming Data and Total Roaming Data

¾Duration: Duration time for each connection; Total time duration for a specied connection

period;

3.2 Clear History

¾Click top right option menu, selected “Clear History” in draw menu

¾When billing day, automatically clear all usage database

¾If usage or time excessed limitation, when set a new usage plan or Time limitation plan,

clear previous database automatically.

¾If usage or time haven’t excessed limitation, When set a new usage plan or time limitation

plan, database will not be cleared

3.3 Usage setting

Click top right option menu, selected “Usage setting” to set Usage data.

4. Message

Click “SMS” area to enter Message interface, the following items are included:

¾+New message: create new SMS;

¾Draft: save the SMS not sent;

¾: delete SMS

¾: send SMS fail

¾: Option Menu

zSMS setting

zDelete all messages

Read/Reply/Forward SMS

Double click a message to read the entire message; same time a SMS box is displayed for

Reply/Forward

5. Settings

Click “Settings” areas to enter Setting, the following items are included:

¾Wi-Fi Settings: set the parameters related to Wi-Fi;

z802.11 Mode: selected the mode used, such as 802.11 a / 802.11 b / 802.11 g / 802.11 n;

zSSID: This is the name of Wi-Fi network, which was used to identify your Wi-Fi network.

The length of the SSID should be 1-32 characters including “_”.

zSSID Broadcast: The default setting is “Enable”.

zWi-Fi Channel: Different domain has different channels (Channel 1~11 in FCC (US)/IC

(Canada); Channel 1~13 in ETSI (Europe); Channel 1~13 in MKK (Japan))

zMax Number of Users: Set the maximum number of Wi-Fi users. The default and

maximum value is “32”.

zSecurity: set the cipher for Wi-Fi; Select an encryption mode in the list and set your

password. If you select “Disable”, any Wi-Fi enabled device can connect to the device

without the password.

zWEP: Lower security. Works with older Wi-Fi devices. Recommended only if your

devices don’t support WPA or WPA2.

zWPA: A strong security standard, supported by most Wi-Fi devices. 8 to 63 ASCII

characters needed.

zWPA2: A stronger, newer security standard. Limited to newer Wi-Fi devices. 8 to 63

ASCII characters needed.

¾Login Settings: dene your login password

zLogin password characters: 4-16, if exceeds 16 characters, not allow to proceed;

zIf an invalid character is input, error message is displayed under user name, data not

saved:

zPassword can contain letters, numbers, and symbols (ASCII characters 4-16), but not

the following: ” ; \ & % + ‘ < > ?

¾Prole management: Edit your prole

¾PIN Code Settings: PIN operation: include three behaviors Enable/Disable/Modify

Note:

1. When you entered wrong PIN 3 times, PUK is needed, you can get this key from the

operator.

2. PIN code:4-8 digits.

¾Connection mode: Automatic or Manual at draw down list;

¾Network mode: Auto, 2G only, 3G only, 4G only modes in draw down list;

¾Advanced Settings

zDHCP

Home Address: The router’s IP address on the LAN. The default setting is

“192.168.1.1”.

Subnet Mask: The router’s internal LAN subnet mask. The default setting is

“255.255.255.0”.

DHCP Server: DHCP Server will automatically assign IP addresses to devices on the

network. The default setting is “Enable”.

DHCP IP Pool: Set a range of IP addresses available to access.

DHCP Lease Time: Amount of time that a Wi-Fi enabled device can use its assigned

IP address before it is required to renew the lease.

zMAC Filter: MAC ltering is used to control specic MAC addresses to access, include

Disable, Allow, and Deny.

Note: The maximum allowed MAC list is 10

¾About: Display your device basic information

zReboot: Restart the device

zReset: Reset the device to the original factory settings

6. More

¾Online update

Device Auto check SW version, if detect a new SW version, online update reminder icon

display on home page and also under more function sync display.

7. Help

Click Help to open the User Manual.

8. Charging the device

Charging begins when you connect the 3.0 USB cable with

Charger and the device.

When the device is powered off, charging will take a maximum

of 3 hours.

Note: To protect the battery, charge the device when the low

power LCD indicator.

9. Charging up other devices

Use the OTG cable insert the device to power up other

devices like tablets and smartphones. (Only 3600mAh battery

version with this function.)

10. Warranty

• The device is warranted against any deviation from technical specications for a period of

twelve (12) months from the date specied on your original invoice1.

• Under the terms of this warranty, you must immediately inform your vendor in case of a

conformity defect on this device, and present a proof of purchase.

• The vendor or repair center will decide whether to replace or repair this device, as

appropriate.

• Repaired or replaced this device are warranted ONE (1) month unless there are statutory

provisions to the contrary.

• This warranty shall not apply to damage or defects to this device due to:

1) Not following the instructions for use or installation,

2) Not being compliant with technical and safety standards applicable in the geographical

area where this device is used,

3) Improper maintenance of sources of energy, and of the overall electric installation,

4) Accidents or consequences of theft of the vehicle in which this device is transported,

acts of vandalism, lightning, re, humidity, inltration of liquids, inclement weather,

1 The mandatory warranty period may vary if overriding statutory provisions are applicable in your jurisdiction.

5) Connecting to or integrating into this device any equipment not supplied or not

recommended by the manufacturer,

6) Any servicing, modication or repair performed by individuals not authorised by the

manufacturer, the vendor or the approved maintenance centre,

7) Use of this device for a purpose other than that for which it was designed,

8) Malfunctions caused by external causes (e.g., radio interference from other equipment,

power voltage uctuations),

9) Faulty connections resulting from unsatisfactory radio transmission or caused by the

absence of radio relay coverage.

• Warranty is also excluded for this device on which markings or serial numbers have been

removed or altered.

• This device is also warranted against hidden defects (defects inherent in the design,

manufacture, etc.).

• There are no other express warranties than this printed limited warranty, expressed or

implied, of any nature whatsoever.

• In no event shall the manufacturer be liable for incidental or consequential damages of any

nature whatsoever, including but not limited to trading loss, commercial loss, to the full

extent those damages can be disclaimed by law. Some countries/states do not allow the

exclusion or limitation of incidental or consequential damages, or limitation of the duration

of implied warranties, so the preceding limitations or exclusions may not apply to you.

11. Q&A

1. Q: Which browser does the device support?

A: It supports Firefox, Safari 4.0.2----5. 2, IE 7.0----11.0, Opera; Chrome;

2. Q: Which OS does the device support?

A: It supports windows Xp/Vista/7/8; Mac OS X10.5----10.10;

3. Q: How to connect to the device?

A: Open your wireless network connection list and select the relative SSID.

Windows: Right-click Wireless network connection on the task bar, and select

View Available Networks.

Mac: Pull down list from AirPort icon. Select the SSID from the dropdown menu.

iOS: Settings->Wi-Fi. Choose the SSID from the available Networks.

Android: Settings->Wireless controls->Wi-Fi settings. Choose SSID from the

available Networks.

4. Q: How to do if I see the SSID but failed to connect?

A: Check the password you entered is the right one.

5. Q: How to do if No service ?

A: the possible reason are listed as bellow:

1. Unstable local signal.

2. Hardware problem.

You may:

1. If you are inside a building or near a structure that may be blocking the signal,

change the position or location of the device. For example, try moving the device

close to a window.

2. Check the hardware or use another device and retry.

6. Q: How to do if I forgot Wi-Fi Key?

A: You can reset the device to factory defaults by press and hold Power key and Menu

key 3 seconds.

7. Q: Why the SSID does not appear in the wireless network list?

A: You can check the device as the suggestion bellow:

zCheck the device Status Display for error messages or information.

zRefresh your network list on your computer.

Windows: Click Refresh Network List on the left side of the Wireless Network

Connection screen.

If that does not work you can try the following:

1. Open Network Connections.

2. Right-click Wireless Network Connection and select Properties.

3. Click the Wireless Networks tab.

4. Delete any unused wireless connections from the Preferred Networks list and

click OK.

5. Restart your computer.

Mac:Try rebooting your computer

8. Q: How to do if “PIN lock” or “PUK lock”?

A: The SIM card is locked. Login Web page and Enter your PIN code or PUK code you

got from the operator.

Note: if you entered wrong PIN 3 times, then PUK is needed, and if the wrong PUK

entered 10 times, the SIM card will be locked forever.

9. Q: How to connect/disconnect to the 4G/3G network?

A: Login the web browser, go to Connection click “Connect/Disconnect” button

10. Q: How to set a new PIN for my SIM card?

A: Login web browser, Go to Settings->Pin Code Settings

11. Q: Where can I nd information about Internet connectivity and Wi-Fi setup?

A: Login web browser, Go to Connection

12. Q: How to check the volume and time i used before?

A: Login web browser, Go to Usage

13. Q: How to search the network manually?

A: Login web browser,Go to Settings->Network mode,choose manual for network

selection;

14. Q: How to check the model number and rmware versions of my device?

A: Login web browser, go to Settings->About

15. Q: Can I backup and restore my conguration settings?

A: Login web browser, go to Settings->About

16. Q: How to set the device dials to connect internet automatically when turn on the

device?

A: login web browser, and go to Settings->Network mode->AUTO

17. Q: How to change the SSID?

A: login web browser, and go to Settings->Wi-Fi settings

18. Q: How to change the login password?

A: login web browser, and go to Settings->Login settings

19. Q: How to change the Wi-Fi Key?

A: login web UI, and go to Settings->Wi-Fi settings

12. Warning and Precautions

Electronic Device

Turn off your device near high-precision electronic devices. The wireless device may affect

the performance of these devices. Such devices include hearing aids, pacemakers, re alarm

system, automatic gates, and other automatic devices can be affected. If you are using an

electronic medical device, consult the device manufacturer to conrm whether the radio wave

affects the operation of this device.

Hospital

Pay attention to the following points in hospitals or health care facilities:

¾Do not take your wireless device into the operating room, intensive care unit, or coronary

care unit.

¾Do not use your wireless device at places for medical treatment where wireless device use

is prohibited.

Storage Environment

¾Do not place magnetic storage media such as magnetic cards and oppy disks near the

wireless device. Radiation from the wireless device may erase the information stored on

them.

¾Do not put your wireless device and other accessories in containers with strong magnetic

eld, such as an induction cooker and a microwave oven. Otherwise, circuit failure, re, or

explosion may occur.

¾Do not leave your wireless device in a very hot or cold place. Otherwise, malfunction of

the products, re, or explosion may occur.

¾Do not subject your wireless device to serious collision or shock. Otherwise, wireless

device malfunction, overheat, re, or explosion may occur.

Children Safety

¾Put your wireless device in places beyond the reach of children. Do not allow children to

use the wireless device without guidance.

¾Do not allow children to put the device in mouth.

¾Do not allow children to touch the small ttings. Otherwise, suffocation or gullet jam can

be caused if children swallow the small ttings.

Indice

Altri manuali Alcatel Router di rete

Alcatel

Alcatel LINKZONE 2 Manuale utente

Alcatel

Alcatel SPEED TOUCH 570 Manuale di istruzioni

Alcatel

Alcatel Speed Touch Home Manuale utente

Alcatel

Alcatel OmniSwitch 8800 Manuale di installazione

Alcatel

Alcatel OmniStack OS-LS-6248 Manuale utente

Alcatel

Alcatel Y850 Manuale utente

Alcatel

Alcatel SPEED TOUCH 710 Manuale utente

Alcatel

Alcatel Omni Switch/Router Manuale utente

Alcatel

Alcatel SpeedTouch 610 Manuale utente

Alcatel

Alcatel SPEED TOUCH PRO Manuale utente

Alcatel

Alcatel OS6850-48L Manuale utente

Alcatel

Alcatel LINKZONE Manuale utente

Alcatel

Alcatel 7750 SR-12 Manuale utente

Alcatel

Alcatel LINKHUB HH71V1 Manuale utente

Alcatel

Alcatel Speed Touch Wireless Manuale utente

Alcatel

Alcatel SPEEDTOUCH 710 Manuale utente

Alcatel

Alcatel OmniStack OS-LS-6224 Manuale utente

Alcatel

Alcatel SpeedTouch 570 Guida di sicurezza

Alcatel

Alcatel OS6400-48 Manuale di installazione

Alcatel

Alcatel Speed Touch 591s Manuale utente

Alcatel

Alcatel LINKHUB HH71VM Manuale utente

Alcatel

Alcatel OS-6124 Manuale utente

Alcatel

Alcatel AST570 Manuale utente

Alcatel

Alcatel 3EC 16964 AAAA-AAZZA Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza