ALcom Clarigo C11 Manuale
1
2
Contents
Setup Flow Chart...................................................... .... ..3
Part I. System Information
1.1 Reset to default................................................. ... ..4
1.2 Firmware version............................................... .. ..4
Part II. Interface Setting
2.1 Interface ........................................................... .....5
Part III. Keyboard Parameters
3.1 Terminal Type .................................................... ...6
3.2 Language Selection ......................................... .....7
3.3 Function Key Emulation ................................ ..... .8
3.4 Keyboard Emulation .................................... .........8
3.5 ALT Mode ..................................................... ........9
3.6 Caps Lock ..................................................... ........9
3.7 Numeric Key .................................................. .......9
3.8 Inter-Character Delay .................................... ......10
3.9 Delay After Transmit (Keyboard Wedge) ...... ......10
3.10 Keyboard Speed ........................................... ....10
3.11 Keyboard Wedge Terminator ......................... ...10
Part IV. RS-232 Protocol
4.1 Baud Rate ................................................... ...... .11
4.2 Data Bits ....................................................... ..... 11
4.3 Stop Bits ....................................................... ... .12
4.4 Parity Check .................................................. ... 12
4.5 Inter-Character Delay ...................................... . ..12
4.6 Delay After Transmit ...................................... ... . 12
4.7 Response Delay Time .................................... ... .13
4.8 Flow Control .................................................... . ..13
4.9 RS-232 Interface Terminator ......................... ... ..13
Part V. System Setting
5.1 Scan Mode .................................................... .. ...15
3
5.2 Buzzer ......................................................... ........16
5.3 String ............................................................. .....18
5.4 Barcode Inverse .......................................... ........20
Part VI. Barcode Type Setting
6.1 UPC-A ....................................................... ..........22
6.2 UPC-E ..................................................... ............24
6.3 EAN-13........................................................... .....26
6.4 EAN-8................................................... ...............28
6.5 Code 39...................................................... .........29
6.6 Codabar....................................................... ........32
6.7 Code 93......................................................... ......34
6.8 Code 128 .................................................... ........36
6.9 Interleaved 2 of 5......................................... .......38
6.10 Industrial 2 of 5.......................................... ........40
6.11 Matrix 2 of 5............................................ ...........42
6.12 China Post Code.................................... .......... .44
6.13 MSI/Plessey........................................... ......... ..45
6.14 Code 32................................................... ..........47
6.15 Code 11........................................................ .....49
6.16 RSS (Optional) ......................................... ...... . 51
6.17 Telepen ................................................. ........... 52
Appendix A.................................................... ............ . 54
Appendix B................................................... .......... . 56
4
Setup Flow Chart
◆Note:
Note:Note:
Note:
1. Scan “firmware version barcode”, the
Version No. will
be displayed on monitor.
The default settings are shown with < > and bold in the
following sections.
Scan “End” barcode
Scan the barcode you like to
change to change
Hex or ASCII Code
Reset to default
YES
NO
5
Part I
Part I Part I
Part I System
SystemSystem
System
Information
InformationInformation
Information
1.1 Reset to default
Reset to defaultReset to default
Reset to default:
::
:
Reset to factory default settings. The default s
ettings
are shown with < > and bold.
1.2 Display
Display Display
Display Firmware Version
Firmware VersionFirmware Version
Firmware Version:
::
:
Scan barcode to display firmware version.
Start Configuration
Reset to default
Firmware Version
End Configuration
6
Part II System Setting
2.1 Interface:
2.1 Interface:2.1 Interface:
2.1 Interface:
Part I System Information
7
1.3 Reset to default:
Reset to factory default settings. The default settings are
shown with < > and bold.
1.4 Display Firmware Version:
Scan barcode to display firmware version.
Start Configuration
Reset to default
Firmware Version
End Configuration
Part II System Setting
8
2.1 Interface:
Start Configuration
PS/2
Keyboard
RS-232
< USB
Keyboard >
< USB
Virtual COM >
End Configuration
Part III Keyboard wedge parameters
9
3.1 Terminal Type:
Start Configuration
< IBM AT >
Reserved
Reserved
Reserved
Reserved
Reserved
10
Reserved
Reserved
End Configuration
3.2 Language Selection:
Start Configuration
American
Italian
Spanish
Indice
Manuali Lettore di codici a barre popolari di altre marche
POSMicro
POSMicro Datalogic PowerScan D7100 Manuale utente
Marson
Marson MT780 Guida rapida alla configurazione
NCR
NCR RealPOS Manuale utente
Motorola
Motorola SE3300 Guida rapida alla configurazione
Element
Element P130BT Manuale utente
Motorola
Motorola Symbol LS3008 Manuale di installazione e funzionamento
