Allen-Bradley SLC 5/01 Manuale utente

SLC 5/01™ and SLC 5/02™ Modular

Processors

(Catalog Numbers 1747-L511, 1747-L514,

1747-L524)

Installation Instructions

English Section . . . . . . . . . . . . . . . . 3

Section en francais . . . . . . . . . . . . . 15

Deutscher Abschnitt . . . . . . . . . . . . 27

Sezione italiana . . . . . . . . . . . . . . . 39

Sección en español . . . . . . . . . . . . 51

Inside... page

Allen-Bradley Replacements

SLC 5/01™ and SLC 5/02™ Modular

Processors

(Catalog Numbers 1747-L511, 1747-L514,

1747-L524)

Installation Instructions

English Section

Important User Information . . . . . . . . .4

For More Information . . . . . . . . . . . . 5

Required Tools and Equipment . . . . 6

Safety Considerations . . . . . . . . . . . 6

Installation Procedure . . . . . . . . . . . 7

Troubleshooting . . . . . . . . . . . . . . . . 9

Specifications . . . . . . . . . . . . . . . . . 10

Battery Handling, Storing, and

Transporting (Cat. No. 1747-BA) . . 12

Inside... page

Publication 1747-5.25

Important User Information

Because of the variety of uses for the products described in this publication, those

responsible for the application and use of this control equipment must satisfy

themselves that all necessary steps have been taken to assure that each

application and use meets all performance and safety requirements, including any

applicable laws, regulations, codes and standards.

The illustrations, charts, sample programs and layout examples shown in this

guide are intended solely for purposes of example. Since there are many

variables and requirements associated with any particular installation,

Allen-Bradley does not assume responsibility or liability (to include intellectual

property liability) for actual use based upon the examples shown in this

publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application,

Installation, and Maintenance of Solid-State Control (available from your local

Allen-Bradley office), describes some important differences between solid-state

equipment and electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole or in part,

without written permission of Allen-Bradley Company, Inc., is prohibited.

Throughout these installation instructions we use notes to make you aware of

safety considerations:

Attention statements help you to:

• identify a hazard

• avoid the hazard

• recognize the consequences



ATTENTION: Identifies information about practices or

circumstances that can lead to personal injury or death, property

damage or economic loss

Important: Identifies information that is critical for successful application and

understanding of the product.

Allen-Bradley Replacements

Publication1747-5.25

For More Information

As part of our effort to preserve, protect, and improve our environment,

Allen-Bradley is reducing the amount of paper we use. Less paper means more

options for you. In addition to traditional printed publications and CD-ROM

versions, we now offer on-line manuals with the most up-to-date information you

can get. We recommend that you read the related publications listed below

before starting up your control system.

Related Publications

If you would like a manual, you can:

• download a free electronic version from the internet:

www.theautomationbookstore.com

• purchase a printed manual by:

— contacting your local distributor or Rockwell Automation

representative

— visiting www.theautomationbookstore.com and placing your order

— calling 1.800.963.9548 (USA/Canada) or

001.330.725.1574 (Outside USA/Canada)

For Refer to this Document Pub. No.

A more detailed description on how to

install and use your modular SLC 500

system.

SLC 500 Modular

Hardware Style Installation

and Operation Manual

1747-6.2

A reference manual that contains status

file data, instruction set, and

troubleshooting information.

SLC 500 and MicroLogix

1000 Instruction Set

Reference Manual

1747-6.15

A CD–ROM containing both of the

manuals listed above, plus the:

•SLC 500 Analog I/O Modules User

Manual

•Discrete I/O Modules Installation

Instructions

•Discrete I/O Modules Product Data

SLC 500 Literature

Collection on CD–ROM 1747-CD1-1

Publication 1747-5.25

Required Tools and Equipment

• medium blade screwdriver

• programming equipment

• a 1747-PIC, 1784-KTX, or 1784-PCMK communication interfaces

Safety Considerations

For general recommendations concerning installation safety requirements and

safety related work practices, refer to the requirements specific to your region.

•Europe: Reference the standards found in EN 60204 and your national

regulations.

•United States: refer to NFPA 70E, Electrical Safety Requirements for

Employee Workplaces.



ATTENTION: Never install, remove, or wire any module while

power is applied. Also, do not expose processor modules to

surfaces or other areas that may typically hold an electrostatic

charge. Electrostatic charges can alter or destroy memory.

Important: See page 10 for information on proper battery handling, storage, and

transporting.

Allen-Bradley Replacements

Publication1747-5.25

Installation Procedure

Install the Battery

1. Open the door of the processor.

2. Remove the jumper from the battery connector socket. Store the jumper in

a safe place for possible future use without the battery.

3. Insert a new or replacement battery in the holder making sure it is held in by

the retainer clips.

4. Plug the battery connector into the socket. See the figure below.

5. Close the processor door.

Important: If your processor has a battery— the battery is an option for the SLC

5/01 (1747-L511) processor — make sure it is connected before

installing your processor into the chassis. This provides memory

backup for your processor should the controller power supply fail.

Important: See page 10 for information on proper battery handling, storage, and

transporting.

White

Lead

Red

Lead Battery

Connector

Retainer

Clips

Publication 1747-5.25

Install the Processor

Make sure system power is off; then insert the processor into slot 0 of the 1746

chassis.

Apply Power to the Processor

1. Energize the chassis power supply.

2. Check the chassis power supply and processor LEDs. The power LED on the

power supply should be on and the fault LED on the processor should be

flashing.

Important: The SLC 500t Modular Processors must be inserted into the left slot

(slot 0), as shown below. In addition, remove the protective wrap after

installing the processor.

Processor

Release

Card Guide

Protective Wrap

Power

Supply

Indicates the LED is OFF.

Indicates the LED is ON.

Indicates the LED is

FLASHING.

Status of LED does not matter.

POWER RUN

CPU FAULT

FORCED I/O

BATTERY LOW

COMM

The RUN LED on the SLC 5/01

processor is actully labeled “PC

RUN.” Also, the SLC 5/01 processor

does not have a COMM LED.

Allen-Bradley Replacements

Publication1747-5.25

Load Your Software

Refer to your programming software documentation.

Establish Communications with the Processor

1. Connect the 1747-PIC to the processor and your personal computer.

2. Set the communication parameters of the software to match the default

parameters of the processor:

— DH-485

— 19.2k baud

— Node Address = 1

Troubleshooting

Before troubleshooting your SLC 500 system, please obtain an SLC 500 Modular

Hardware Style Installation and Operation Manual (1747-6.2) from one of the

sources listed on page 3. Refer to the chapter on Troubleshooting.

In addition to the SLC 500 Modular Hardware Style Installation and Operation

Manual, the SLC 500 and MicroLogix 1000 Instruction Set Reference Manual

(1747-6.15) may also be obtained from the sources listed on page 3. This manual

contains explanations and examples for the entire instruction set as well as for all

status words and bits. It also contains explanations for all possible fault codes

found in status word S:6.

Publication 1747-5.25

Specifications

Specification SLC 5/01

(1747-L511, -L514) SLC 5/02

(1747-L524)

Program Memory 1K or 4K Instructions 4K Instructions

Additional Data Storage 0 0

Maximum I/O Capacity 3940 discrete inputs

3940 discrete outputs 4096 discrete inputs

4096 discrete outputs

Max. Local Chassis/Slots 3/30 3/30

Programming Software RSLogix 500™ , PLC–500 A.I. Series™, APS, and HHT

Programming Instructions 52 71

Typical Scan Time(1)

(1) The scan times are typical for a 1K ladder logic program consisting of simple ladder logic and

communication servicing. Actual scan times depend on your program size, instuctions used, and

the communication protocol.

8 ms/K 4.8 ms/K

Bit Execution (XIC) 4 µs 2.4 µs

Communication Receive Receive or Initiate

DH-485 SLC 5/01(1)

(1) A 1747-PIC is required when connecting to the DH-485 channel for programming.

SLC 5/02(1)

Allen-Bradley Replacements

Publication1747-5.25

The following table summarizes the available memory back up options for the

SLC 5/01 and SLC 5/02 processors. EEPROM and UVPROM memory modules

provide non-volatile memory back-up.

Description Specification

Power Supply Loading at 5V dc 350 mA

Power Supply Loading at 24V dc 105 mA

Program Scan Hold-up Time after Loss of

Power 20 ms to 3 s (dependent on power supply loading)

Noise Immunity NEMA Standard ICS 2-230

Vibration Displacement: 0.015 inch, peak-to-peak at 5-57

Acceleration: 2.5Gs at 57-2000 Hz

Shock (operating) 30Gs

Ambient Temperature Rating Operating: 0 to + 60

C (32

F to 140

Storage: 40

C to 85

C (-40

F to 185

Humidity 5 to 95% without condensation

Agency Certification UL listed

CSA approved

Class 1, Groups A, B, C or D, Division 2

CE compliant for all applicable directives

Memory Back Up Option SLC 5/01

(1747-L511/1747-L514) SLC 5/02

(1747-L524)

EEPROM 1747-M1, 1747-M2 1747-M2

UVPROM 1747-M3, 1747-M4 1747-M4

Altri manuali per SLC 5/01

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Allen-Bradley Hardware per computer

Allen-Bradley

Allen-Bradley SLC 5/04 Manuale utente

Allen-Bradley

Allen-Bradley PLC-5 MAP/OSI Manuale utente

Allen-Bradley

Allen-Bradley 2094-AL15S Manuale utente

Allen-Bradley

Allen-Bradley Mini-PLC Mini-PLC-2/16 Manuale utente

Allen-Bradley

Allen-Bradley SLC 5/03 Manuale utente

Allen-Bradley

Allen-Bradley 1771-SF1 Manuale utente

Allen-Bradley

Allen-Bradley SLC 500 Series Manuale utente

Allen-Bradley

Allen-Bradley SLC 5/01 Manuale utente

Allen-Bradley

Allen-Bradley 2707-MVH232 Manuale utente

Allen-Bradley

Allen-Bradley SLC 5/03 Manuale utente

Allen-Bradley

Allen-Bradley 2707 Manuale utente

Allen-Bradley

Allen-Bradley 1747-DCM Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente