Allen-Bradley SLC 5/03 Manuale utente

Publication 1747-IN009A-ML-P

Installation Instructions

SLC 5/03™, SLC 5/04™, and SLC 5/05™

Modular Processors

(Catalog Numbers 1747-L531, 1747-L532,

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553)

To Use Publication

Install your chassis

Installation du châssis

Installation des Chassis

Installazione dello chassis

Instalar el chasis

Instalar o chassi

1746-5.8

Install your power supply

Installation de l’alimentation

Installation des Netzteils

Installazione dell’alimentatore

Instalar la fuente de alimentación eléctrica

Instalar a fonte de energia

1746-IN004A-ML-P

Install your processor

Installation de processeur

Installation des Prozessors

Installazione del processore

Instalar el procesador

Instalar o processador

1747-IN009A-ML-P

English Section.................................... 3

Section en français............................ 15

Deutscher Abschnitt.......................... 27

Sezione italiana................................. 39

Sección en español............................ 51

Seção em português.......................... 63

Allen-Bradley Parts

2SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009A-ML-P

Installation Instructions

English Section

SLC 5/03™, SLC 5/04™, and SLC 5/05™

Modular Processors

(Catalog Numbers 1747-L531, 1747-L532,

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553)

Inside…........................................................................................page

Important User Information.................................................................. 4

For More Information ........................................................................... 5

Required Tools and Equipment............................................................. 6

Safety Considerations.......................................................................... 6

Installation Procedure .......................................................................... 7

Troubleshooting.................................................................................. 11

Specifications..................................................................................... 11

Battery Handling, Storing, and Transporting (Cat. No. 1747-BA) ...... 13

Allen-Bradley Parts

4SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009A-ML-P

Important User Information

Because of the variety of uses for the products described in this publication, those

responsible for the application and use of this control equipment must satisfy

themselves that all necessary steps have been taken to assure that each application

and use meets all performance and safety requirements, including any applicable

laws, regulations, codes and standards.

The illustrations, charts, sample programs and layout examples shown in this guide

are intended solely for purposes of example. Since there are many variables and

requirements associated with any particular installation, Allen-Bradley does not

assume responsibility or liability (to include intellectual property liability) for actual

use based upon the examples shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation,

and Maintenance of Solid-State Control (available from your local Allen-Bradley

office), describes some important differences between solid-state equipment and

electromechanical devices that should be taken into consideration when applying

products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole or in part,

without written permission of Allen-Bradley Company, Inc., is prohibited.

Throughout these installation instructions we use notes to make you aware of safety

considerations:

Attention statements help you to:

•identifyahazard

•avoidthehazard

• recognize the consequences

!ATTENTION: Identifies information about practices or

circumstances that can lead to personal injury or death, property

damage or economic loss.

Important: Identifies information that is critical for successful application and

understanding of the product.

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 5

Publication 1747-IN009A-ML-P

For More Information

As part of our effort to preserve, protect, and improve our environment, Allen-

Bradley is reducing the amount of paper we use. Less paper means more options for

you. In addition to traditional printed publications and CD-ROM versions, we now

offer on-line manuals with the most up-to-date information you can get. We

recommend that you read the related publications listed below before starting up

your control system.

Related Publications

If you would like a manual, you can:

• download a free electronic version from the internet:

www.theautomationbookstore.com

• purchase a printed manual by:

– contacting your local distributor or Rockwell Automation representative

– visiting www.theautomationbookstore.com and placing your order

– calling 1.800.963.9548 (USA/Canada)

or 001.330.725.1574 (Outside USA/Canada)

For Refer to this Document Pub. No.

A more detailed description on how to install

and use your modular SLC 500 system. SLC 500 Modular Hardware

Style InstallationandOperation

Manual

1747-6.2

A reference manual that contains status file

data, instruction set, and troubleshooting

information.

SLC 500 and MicroLogix 1000

Instruction Set Reference

Manual

1747-6.15

A CD-ROM containing both of the manuals

listed above, plus the:

SLC 500 Analog I/O Modules User Manual

Discrete I/O Modules Installation Instructions

Discrete I/O Modules Product Data

SLC500LiteratureCollectionon

CD-ROM 1747-CD1-1

Allen-Bradley Parts

6SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009A-ML-P

Required Tools and Equipment

• medium blade screwdriver

• programming equipment

• a 1747-PIC, 1784-KTX, or 1784-PCMK communication interface (or standard

Ethernet PC board - SLC 5/05 only)

Safety Considerations

For general recommendations concerninginstallation safety requirements and safety

related work practices, refer to the requirements specific to your region.

•Europe: Reference the standards found in EN 60204 and your national

regulations.

•United States: refer to NFPA 70E, Electrical Safety Requirements for Employee

Workplaces.

!ATTENTION: Never install, remove, or wire any module while

power is applied. Also, do not expose processor modules to surfaces

or other areas that may typically hold an electrostatic charge.

Electrostatic charges can alter or destroy memory.

Important: See page 13 for information on proper battery handling, storage, and

transporting.

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 7

Publication 1747-IN009A-ML-P

Installation Procedure

Install the Processor

Make sure system power is off; then insert the processor into slot 0 of the 1746

chassis.

Apply Power to the Processor

1. Energize the chassis power supply.

2. Check the chassis power supply and processor LEDs. The power LED on the

power supply should be on and the fault LED on the processor should be

flashing. See the figure on page 8 for location of the power supply and processor

LEDs.

Important: The SLC 500 modular processors must be inserted into the left slot

(slot 0), as shown below. In addition, remove the protective wrap after

installing the processor.

Power

Supply

Protective Wrap

Card Guide

Processor Release

Allen-Bradley Parts

8SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009A-ML-P

Load Your Software

Refer to your programming software documentation.

Establish Communication to the Processor

1. Refer to the following table to establish communication between the processor

and your personal computer.

Processor Procedure

SLC 5/03 Connect 1747-PIC from the processor to your personal computer or a 1747-CP3

cable from channel 0 of the processor to the personal computer serial port.

SLC 5/04 Connect a 1747-CP3 cable from channel 0 of the processor to the personal

computer serial port or use a 1784-KT, 1784-KTX, 1784-KT2, or 1784-PCMK

card.

SLC 5/05 Connect a 1747-CP3 cable from channel 0 of the processor to the personal

computer serial port or use a 1784-KT, 1784-KTX, 1784-KT2, or -PCMK card. For

Ethernet connection, connect channel 1 of the processor and the PC Ethernet

Card (or 1784-PCMK) to an Ethernet hub using 10Base-T cable.

POWER RUN

FLT

BATT

FORCE

DH485

RS232

POWER RUN

FLT

BATT

FORCE

DH+

RS232

POWER RUN

FLT

BATT

FORCE

ENET

RS232

Power Supply and LED Indicators Indicates the LED is OFF

Indicates the LED is ON

Indicates the LED is FLASHING

Status of LED doesnot matter

SLC 5/05

SLC 5/04

SLC 5/03

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 9

Publication 1747-IN009A-ML-P

2. Set the communication parameters of the software to match the default

parameters of the processor:

Replacing the Battery

Your SLC processor provides back-up power for RAM through a replaceable lithium

battery. This battery provides back-up for approximately 2 years. The BATT LED

on the front of the processor alerts you when the battery voltage has fallen below a

threshold level.

To replace the lithium battery follow these steps:

1. Remove power from the SLC 500 power supply.

2. Remove the processor from the chassis by pressing the retainer clips at both the

top and bottom of the module and slide it out.

3. Unplug the battery connector. Refer to the figure on page 10 for battery

connector location.

Channel 0 Configuration Channel1 Configuration

SLC 5/03, 5/04, 5/05 SLC 5/03 SLC 5/04 SLC 5/05

DF1 Full-Duplex:

• no handshaking

• 19.2K baud

• CRC Error Check

• duplicate detect on

• no parity

DH-485:

• 19.2K baud

• node address = 1

DH+™:

• 57.6K baud

• node address = 1

Ethernet

!ATTENTION: Do not remove the processor from the SLC 500

chassis until all power is removed from the SLC 500 power supply

!ATTENTION: Do not expose the processor to surfaces or other

areas that may typically hold an electrostatic charge. Electrostatic

charges can alter or destroy memory.

Allen-Bradley Parts

10 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009A-ML-P

4. Remove the battery from the retaining clips.

5. Insert a new battery into the battery retaining clips.

6. Plug the battery connector into the socket as shown above.

7. Re-insert the module into the SLC 500 chassis.

8. Restore power to the SLC 500 power supply.

9. Close the processor door.

Important: The SLC 5/03, 5/04, and 5/05 processors have a capacitor that

provides at least 30 minutes of battery back-up while the battery is

disconnected. Data in RAM is not lost if the battery is replaced within

30 minutes

Important: See page 13 for information on proper battery handling, storage, and

transporting.

White

Red

Battery Connector

Left Side View

Battery

Altri manuali per SLC 5/03

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Allen-Bradley Hardware per computer

Allen-Bradley

Allen-Bradley 1747-DCM Manuale utente

Allen-Bradley

Allen-Bradley PLC-5 MAP/OSI Manuale utente

Allen-Bradley

Allen-Bradley SLC 5/04 Manuale utente

Allen-Bradley

Allen-Bradley SLC 5/01 Manuale utente

Allen-Bradley

Allen-Bradley 2707-MVH232 Manuale utente

Allen-Bradley

Allen-Bradley 2707 Manuale utente

Allen-Bradley

Allen-Bradley 1771-SF1 Manuale utente

Allen-Bradley

Allen-Bradley 2094-AL15S Manuale utente

Allen-Bradley

Allen-Bradley SLC 5/03 Manuale utente

Allen-Bradley

Allen-Bradley SLC 500 Series Manuale utente

Allen-Bradley

Allen-Bradley Mini-PLC Mini-PLC-2/16 Manuale utente

Allen-Bradley

Allen-Bradley SLC 5/01 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente