Allen-Bradley PanelView Plus 400 Manuale utente

Installation Instructions

PanelView Plus and PanelView Plus Compact

400 and 600 Terminals

Catalog Numbers 2711P-x4xxxx, 2711P-x6xxxx, 2711PC-x4xxxx,

2711PC-x6xxxx

About This Publication

This document provides instructions on how to install these devices in a panel:

•PanelView Plus 400 keypad terminal or keypad and touch terminal

•PanelView Plus 600 keypad, touch, or keypad and touch terminal

•PanelView Plus Compact 400 keypad terminal or keypad and touch terminal

•PanelView Plus Compact 600 touch terminal

For complete information on installing, wiring, and troubleshooting the terminals, refer to the

publications listed under Additional Resources.

Topic Page

Important User Information 2

Environment and Enclosure 3

Hazardous Locations 4

Wiring and Safety Guidelines 8

About the Product 8

Parts List 9

Install the Terminal 10

Remove and Install the Power Terminal Block 15

DC Power Connections 16

AC Power Connections 19

Troubleshooting 21

Battery Removal 25

Specifications 26

Additional Resources 28

AB Parts

2PanelView Plus and PanelView Plus Compact 400 and 600 Terminals

Publication 2711P-IN002G-EN-P - November 2009

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication

SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you identify a hazard,

avoid a hazard and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment (for example, a drive or motor) to alert

people that dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment (for example, a drive or motor) to alert

people that surfaces may reach dangerous temperatures.

PanelView Plus and PanelView Plus Compact 400 and 600 Terminals 3

Publication 2711P-IN002G-EN-P - November 2009

Environment and Enclosure

ControlNet Communication Ports

ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial environment, in

overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m

(6561 ft) without derating.

The terminals are intended for use with programmable logic controllers. Terminals that

are AC powered must also be connected to the secondary of an isolating transformer.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/CISPR 11. Without appropriate precautions, there may be potential difficulties

ensuring electromagnetic compatibility in other environments due to conducted as well

as radiated disturbance.

Korean Radio Wave Suitability Registration - This equipment is registered for

Electromagnetic Conformity Registration as business equipment (A), not home

equipment. Sellers or users are required to take caution in this regard.

This equipment is supplied as open-type equipment. It must be mounted within an

enclosure that is suitably designed for those specific environmental conditions that will

be present and appropriately designed to prevent personal injury resulting from

accessibility to live parts. The interior of the enclosure must be accessible only by the use

of a tool. The terminals meet specified NEMA Type and IEC ratings only when mounted in

a panel or enclosure with the equivalent rating. Subsequent sections of this publication

may contain additional information regarding specific enclosure type ratings that are

required to comply with certain product safety certifications.

In addition to this publication, see:

•Industrial Automation Wiring and Grounding Guidelines, for additional installation

requirements, publication 1770-4.1.

•NEMA Standards publication 250 and IEC publication 60529, as applicable, for

explanations of the degrees of protection provided by different types of enclosure.

ATTENTION PanelView Plus terminals with ControlNet communications ports include a Network

Applications Port (NAP). This port is for temporarily connecting programming terminals

to devices on a ControlNet network, and are not intended for continuous operation.

AB Parts

4PanelView Plus and PanelView Plus Compact 400 and 600 Terminals

Publication 2711P-IN002G-EN-P - November 2009

Hazardous Locations

This equipment is suitable for these locations:

•Class I, Division 2 Groups A, B, C, D

•Class II, Division 2 Groups F, G

•Class III

•Ordinary non-hazardous locations only

The following statement applies to use in hazardous locations.

The terminals have a temperature code of T4 when operating in a 55 °C (131 °F) maximum

ambient temperature. Do not install the terminals in environments where atmospheric gases

have ignition temperatures less than 135 °C (275 °F).

WARNING Explosion Hazard

•Substitution of components may impair suitability for hazardous locations.

•Do not disconnect equipment unless power has been switched off and area is

known to be non-hazardous.

•Do not connect or disconnect components unless power has been switched off.

•All wiring must comply with N.E.C. articles 501, 502, 503, and/or C.E.C. section

18-1J2 as appropriate.

•Peripheral equipment must be suitable for the location in which it is used.

PanelView Plus and PanelView Plus Compact 400 and 600 Terminals 5

Publication 2711P-IN002G-EN-P - November 2009

Environnements dangereux

Cet équipement ne peut être utilisé que dans les environnements suivants :

•Classe I, Division 2, Groupes A, B, C, D ;

•Classe II, Division 2, Groupes F, G ;

•Classe III ;

•ou environnements non-dangereux.

La mise en garde suivante s’applique à une utilisation en environnement dangereux.

Le code de température de fonctionnement des terminaux PanelView Plus est T4 pour une

température ambiante maximale de 55 °C. N’installez pas les terminaux dans des

environnements contenant des gaz atmosphériques inflammables à moins de 135 °C.

WARNING DANGER D’EXPLOSION

•La substitution de composants peut rendre cet équipement impropre à une

utilisation en environnement dangereux.

•Ne pas déconnecter l’équipement sans s’être assuré que l’alimentation est

coupée ou que l’environnement est classé non dangereux.

•Ne pas connecter ou déconnecter des composants sans s’être assuré que

l’alimentation est coupée.

•L’ensemble du câblage doit être conforme, selon le cas, aux articles 501-4(b),

502-4(b) et 503-3(b) du Code national de l’électricité des Etats-Unis.

•L’équipement périphérique doit être adapté à l’environnement dans lequel il

est utilisé.

AB Parts

6PanelView Plus and PanelView Plus Compact 400 and 600 Terminals

Publication 2711P-IN002G-EN-P - November 2009

USB Ports

The PanelView Plus and PanelView Plus Compact terminals contain a single, universal serial

bus (USB) port that comply with hazardous location environments. This section details the

field wiring compliance requirements and is provided in accordance with the National

Electrical Code, article 500.

400 and 600 Terminals Control Drawing

Selected nonincendive field wiring apparatus must have nonincendive circuit parameters

conforming with Table 2.

Table 1 - 400 and 600 USB Port Circuit Parameters

400 and 600

Terminals Voc Isc

CaLa

Groups A and B Groups C and D Groups A and B Groups C and D

Series A and B 5.25V DC 1.68 A 10 µF 10 µF 15 µH 15 µH

Series C or

later

5.25V DC 1.68 A 10 µF 10 µF 3.5 µH 15 µH

Table 2 - Required Circuit Parameters for the USB Peripheral Device

Vmax ≥Voc

Imax ≥Isc

Ci+ Ccable ≤Ca

Li+ Lcable ≤ La

USB

Peripheral

Device

Nonincendive Field

Wiring Apparatus

USB Port

Nonincendive Field Wiring

Associated Nonincendive Field Wiring Apparatus

PanelView Plus 400/600 Host Product

PanelView Plus and PanelView Plus Compact 400 and 600 Terminals 7

Publication 2711P-IN002G-EN-P - November 2009

Application Information

Per the National Electrical Code the circuit parameters of nonincendive field wiring apparatus

for use in hazardous locations shall be coordinated with the associated nonincendive field

wiring apparatus such that their combination remains nonincendive. The 400 and 600

terminals and the USB peripheral device shall be treated in this manner.

The circuit parameters of the 400 and 600 USB port are given in Table 1. The USB peripheral

device and its associated cabling shall have circuit parameters with the limits given in Table 2

for them to remain nonincendive when used with the 400 and 600 USB port. If cable

capacitance and inductance are not known the following values from ANSI/ISA-RP

12.06.01-2003 may be used:

Ccable = 197 µF/m (60 µF/ft)

Lcable = 0.7 µF/m (0.20 µH/ft)

Nonincendive field wiring must be wired and separated in accordance with 501.10(B)(3) of

the National Electrical Code (NEC) ANSI/NFPA 70 or other local codes as applicable.

This associated nonincendive field wiring apparatus has not been evaluated for use in

combination with another associated nonincendive field wiring apparatus.

Symbol Definitions

Voc Open circuit voltage of the host USB port.

Isc Maximum output current of the host USB port.

Vmax Maximum applied voltage rating of the USB peripheral device.

Vmax shall be greater than or equal to Voc in Table 1 (Vmax ≥Voc ).

Imax Maximum current to which the USB peripheral device can be subjected.

Imax shall be greater than or equal to Isc in Table 1 (Imax ≥Isc).

CiMaximum internal capacitance of the USB peripheral device.

CaMaximum allowed capacitance of the USB peripheral device and its associated cable. The

sum of Ciof the USB peripheral device and Ccable of the associated cable shall be less

than or equal to Ca

(Ci+ Ccable ≤Ca).

LiMaximum internal inductance of the USB peripheral device.

LaMaximum allowed inductance of the USB peripheral device and its associated cable. The

sum of Liof the USB peripheral device and Lcable of the associated cable shall be less than

or equal to La

(Li+ Lcable ≤La).

AB Parts

8PanelView Plus and PanelView Plus Compact 400 and 600 Terminals

Publication 2711P-IN002G-EN-P - November 2009

Wiring and Safety Guidelines

Use publication NFPA 70E, Electrical Safety Requirements for Employee Workplaces, IEC

60364 Electrical Installations in Buildings, or other applicable wiring safety requirements for

the country of installation when wiring the devices. In addition to the NFPA guidelines:

•connect the device and other similar electronic equipment to its own branch circuit.

•protect the input power by a fuse or circuit breaker rated at no more than 15 A.

•route incoming power to the device by a separate path from the communication lines.

•cross power and communication lines at right angles if they must cross.

Communication lines can be installed in the same conduit as low-level

DC I/O lines (less than 10V).

•shield and ground cables appropriately to avoid electromagnetic interference (EMI).

Grounding minimizes noise from EMI and is a safety measure in electrical

installations.

For more information on grounding recommendations, refer to the National Electrical Code

published by the National Fire Protection Association.

For more information on terminal wiring and grounding applications, refer to publication

2711P-TD001. You can find this publication in the Literature Library at

http://literature.rockwellautomation.com.

About the Product

The base configured unit of the PanelView Plus 400 and 600 terminals includes these

components:

•Power supply, AC or DC

•Display with keypad, touch screen, or keypad and touch screen

•Processor and memory

•RS-232 and USB ports only or

•RS-232, USB, and Ethernet ports with interface for communication module

The fixed configuration of the PanelView Plus Compact 400 and 600 terminals includes these

components:

•Power supply, DC

•Display with keypad, touch screen, or keypad and touch screen

•Processor and memory

•

RS-232, USB, and Ethernet ports without interface for communication module

PanelView Plus and PanelView Plus Compact 400 and 600 Terminals 9

Publication 2711P-IN002G-EN-P - November 2009

Communication modules for specific protocols can be ordered as separate components for

field installation or factory assembled to base unit (with communication interface) per your

configuration.

Parts List

The terminals are shipped with these items:

•Power terminal block, AC or DC

•Mounting clips

•Installation instructions and panel cutout

Required Tools

These tools are required for installation:

•Panel cutout tools

•Small, slotted screwdriver for securing power and RS-232 port connections

IMPORTANT When using the DH-485 module, catalog number 2711P-RN3, with PanelView Plus 400

and 600 terminals, the cable length must not exceed 30 m (98 ft) to comply with CE

requirements. For longer cable lengths, use the 1761-NET-AIC or 1747-AIC module.

Power Connection,

AC or DC

Communication

Module

Base Configured Unit with:

•USB and RS-232 Ports Only

•USB, RS-232, and Ethernet Ports or

•USB, RS-232, and Ethernet Ports with Interface for Communication Module.

Display

Compact Flash

Card Slot (not shown)

AB Parts

10 PanelView Plus and PanelView Plus Compact 400 and 600 Terminals

Publication 2711P-IN002G-EN-P - November 2009

Install the Terminal

Before installing the terminal in a panel, review these topics:

•Mounting clearances

•Panel cutout dimensions

•Product dimensions

Mounting Clearances

Allow adequate clearance around the terminal, inside the enclosure, for adequate ventilation.

Consider heat produced by other devices in the enclosure. The ambient temperature around

the terminals must be between 0…55 °C (32…131 °F).

Minimum clearances for ventilation are:

•Top clearance: 51 mm (2 in.)

•Bottom clearance: 102 mm (4 in.)

•Side clearances: 25 mm (1 in.)

•Back clearance: 0 mm (0 in.)

Minimum side clearance for insertion of memory card is 102 mm (4 in.).

Panel Cutout Dimensions

Use the full size template shipped with your terminal to mark the cutout dimensions.

Mount the Terminal in a Panel

Mounting levers secure the terminal to the panel. The number of levers you use

(4 or 6) varies by terminal type.

Terminal Type Height, mm (in.) Width, mm (in.)

400 Keypad or Keypad and Touch 123 (4.86) 156 (6.15)

600 Keypad or Keypad and Touch 142 (5.61) 241 (9.50)

600 Touch 123 (4.86) 156 (6.15)

ATTENTION Disconnect all electrical power from the panel before making the panel cutout.

Make sure the area around the panel cutout is clear.

Take precautions so metal cuttings do not enter any components already installed in

the panel.

Failure to follow these instructions may result in personal injury or damage to panel

components.

Altri manuali per PanelView Plus 400

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Allen-Bradley Terminale touch

Allen-Bradley

Allen-Bradley PanelView C200 Manuale utente

Allen-Bradley

Allen-Bradley PanelView 2711C-F2M Manuale utente

Allen-Bradley

Allen-Bradley 2711P Manuale di istruzioni

Allen-Bradley

Allen-Bradley PanelView 800 2711R-T4T Manuale utente

Allen-Bradley

Allen-Bradley PanelView Plus 6 Manuale utente

Allen-Bradley

Allen-Bradley PanelView Plus 6 700 Manuale utente

Allen-Bradley

Allen-Bradley PanelView Plus 7 Manuale utente

Allen-Bradley

Allen-Bradley FLEX 5000 Manuale utente

Allen-Bradley

Allen-Bradley PanelView 800 Manuale utente

Allen-Bradley

Allen-Bradley PanelView 5500 Manuale utente

Allen-Bradley

Allen-Bradley 8510SA-TP Series Manuale utente

Allen-Bradley

Allen-Bradley DeviceNet 1790D-T16BV0 Manuale utente

Allen-Bradley

Allen-Bradley MobileView 2711T-B10R1K1 Manuale utente

Allen-Bradley

Allen-Bradley PanelView Plus 6 Manuale utente

Allen-Bradley

Allen-Bradley PanelView 600 Manuale utente

Allen-Bradley

Allen-Bradley PanelView 2711P-RW1 Manuale utente

Allen-Bradley

Allen-Bradley 1797-TB3S Manuale utente

Allen-Bradley

Allen-Bradley 2711-K5A series Manuale utente

Allen-Bradley

Allen-Bradley PanelView Plus 400 Manuale utente

Allen-Bradley

Allen-Bradley PanelView Plus 7 Manuale utente

Allen-Bradley

Allen-Bradley PanelView 1200 Manuale utente

Allen-Bradley

Allen-Bradley MobileView 2711T-T10R1N1 Manuale utente

Allen-Bradley

Allen-Bradley 2711-TBDC Manuale utente

Allen-Bradley

Allen-Bradley PanelView Plus 7 Manuale utente

Manuali Terminale touch popolari di altre marche

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuale utente

Ingenico

Ingenico AXIUM EX4000 Manuale utente

Heisei Electronics

Heisei Electronics Q-POS 815 Manuale utente

Amano

Amano MTX-15 Manuale utente

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuale utente

Demco

Demco SP7 Manuale utente

Lathem

Lathem PC600 Series Manuale utente

Partner

Partner MF-2352 Manuale utente

NCR

NCR RealPOS 7460-2 Manuale

Simrad

Simrad MS50 Istruzioni per il montaggio

Unitech

Unitech MR350 MKII Guida rapida

Jungheinrich

Jungheinrich WMT 210 Manuale utente

Motorola

Motorola MTP850 Manuale utente

YASKAWA

YASKAWA 62H-MDC0 Manuale utente

MVG industries

MVG industries NeptuLink Manuale utente

Price Industries Limited

Price Industries Limited FDC Manuale di istruzioni

Honeywell

Honeywell TemaKey Manuale utente

EBN

EBN BPC65-B-A16G Manuale utente