Allied Telesis AR400 Series Manuale utente

AR400 SERIES ROUTER

QUICK INSTALL GUIDE

AR400 Series Router Quick Install Guide

Document Number C613-04032-01 REV E.

19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA.

permission from Allied Telesyn.

Allied Telesyn International, Corp. reserves the right to make changes in specifications

and other information contained in this document without prior written notice. The

information provided herein is subject to change without notice. In no event shall Allied

Telesyn be liable for any incidental, special, indirect, or consequential damages

whatsoever, including but not limited to lost profits, arising out of or related to this

manual or the information contained herein, even if Allied Telesyn has been advised of,

known, or should have known, the possibility of such damages.

All trademarks are the property of their respective owners.

Quick Install Guide 3

C613-04032-01 REV E

Models Covered By This Guide

This Quick Install Guide includes information on the following models:

■AR410

■AR410S

■AR450S

Quick Install Guide updates can be found at

www.alliedtelesyn.co.nz/support/ar400/

Package Contents

The following items are included with each AR400 Series router. Contact your

sales representative if any items are damaged or missing.

■One AR400 Series router.

■One AC power cord.

■One power cord retaining clip.

■One terminal cable for connecting the router to a terminal or PC.

■Two UTP network cables.

■One rack-mount kit with brackets and screws.

■One AR400 Series Router Quick Install Guide.

■One Safety and Statutory Information booklet.

■One AR400 Series Router Documentation and Tools CD-ROM (which

includes the complete AR400 Series Document Set and utilities).

■One warranty card.

AR400 Series Router

AR400 Series Quick Install Guide

AR Router Hardware Reference

AR400 Series Software Reference

Printed Acrobat PDF

Documentation Roadmap

Website

AR400 Series User Guide

AR400 Series Safety and Statutory Information

General Customer Support

Visit www.alliedtelesyn.co.nz for

the latest documentation, FAQ,

and support information

Port Interface

PIC Quick

PIC Hardwar

Cards

Install Guide

e Reference

4AR400 Series Router

C613-04032-01 REV E

Selecting a Site

The router can be installed in a standard 19-inch rack, or on a level surface such

as a desktop or bench. When installing the router, choose a site that:

■Allows adequate airflow around the router and its vents.

■Is free of dust and moisture.

■Will maintain an ambient temperature range of 0 to 40º C (32 to 104º F) and

a humidity range of 5 to 95% non-condensing.

■Has a reliable and earthed (grounded) power supply circuit, preferably

dedicated and filtered.

■Does not expose cabling to sources of electrical noise, such as radio

transmitters, broadband amplifiers, power lines, electric motors, and

fluorescent fixtures.

■Allows easy access to the router’s power and cable connections.

Installing the Router

This equipment must be earthed.

Follow these steps to install the router:

1. Read the safety information.

For safety information, see the Safety and Statutory Information booklet. A

copy of this booklet is supplied with each router, and can also be found on

the Documentation and Tools CD-ROM or at

www.alliedtelesyn.co.nz/support/ar400/

2. Gather additional items you will need.

To install the router in a rack you will need a Phillips #1 screwdriver. You

will also need screws and cage nuts to attach the brackets to your rack.

If also installing an optional Port Interface Card (PIC), you will need a PIC

Quick Install Guide (AR410 and AR410S routers only).

3. Unpack the router.

Verify the package contents. If any items are damaged or missing, contact

your sales representative.

4. Place the router in its operating location.

See the previous “Selecting a Site” section for guidelines on choosing a

suitable location. To install the router in a rack:

• Ensure the rack has sufficient space for the router and its associated

cables. The router is 1U high

• Unscrew the feet

Quick Install Guide 5

C613-04032-01 REV E

• Screw the handles to the wider side of each bracket, using the supplied

M3 screws (see Figure 1)

• Screw the brackets to the sides of the router, using the supplied M3

screws (see Figure 1). The router can be front or rear mounted

Figure 1: Connecting the rack mount bracket to the router.

• Mount the router in the rack using appropriate rack mounting screws

(not supplied)

5. Install expansion options (AR410 and AR410S routers).

If you purchased an optional PIC, install it now by following the PIC Quick

Install Guide. That guide can be found on the Documentation and Tools

CD-ROM or can be downloaded from

www.alliedtelesyn.co.nz/support/ar400/.

6. Check the supply voltage and the router’s rated voltage.

AR400 Series routers are fitted with a universal mains power supply that

will function over the range 100-240 VAC and 50–60Hz.

The specific power supply requirements for a particular model are clearly

displayed on the rear or underside of the router. If the supply is outside the

accepted range for the router, the router may not operate or damage to the router

may result.

7. Apply power to the router.

Fit the power cord retaining clip to the AC power inlet on the router’s rear

panel.

Connect the provided power cord to the AC power inlet and clip it in

place. Switch the router’s power switch to the ON position. The Power

LED will light continuously and the System LED will flash briefly. The Port

LEDs may also light briefly.

If the LEDs fail to light, the most likely cause is that the router is not

receiving power. Check that

• The power supply outlet’s switch (if any), and the router’s power

switch, are in the ON position

6AR400 Series Router

C613-04032-01 REV E

• The power cable is securely plugged in

• The power supply is operational

If the LEDs light incorrectly, refer to the AR Router Hardware Reference for

troubleshooting information.

Figure 2: Front and rear panels of an AR450S, showing the AC power inlet, power switch, console ports and

Ethernet ports, and their associated LEDs.

Figure 3: Rear panel of an AR410, showing the AC power inlet, power switch, console port, Ethernet ports, and

an optional PIC card.

POWER

SYN

AC Power Switch

AC Power Inlet Console Port10/100 Switch Ports

PIC Bay (with optional

AT-AR023 SYN PIC)

CONSOLE RS-232

PIC BAY0

3X ASYN0

2X 1X

POWER

10BASE-T/100BASE-TX SWITCH PORTS

X PC

= HUB

ETH0

ETH 0

Quick Install Guide 7

C613-04032-01 REV E

Configuring the Router

AR400 Series routers can be configured via the Command Line Interface (CLI)

or Graphical User Interface (GUI).

Using the CLI to configure a router:

1. Initiate router start-up.

Using the terminal cable supplied, connect a VT100-compatible terminal,

or the COM port of a PC running a terminal emulation program such as

Windows Terminal, to the Console RS-232 (ASYN0) port on the router’s

rear panel.

Set the communication parameters on your terminal or terminal emulation

program to:

• Baud rate: 9600

• Data bits: 8

•Parity:None

•Stopbits:1

• Flow control: Hardware

See the AR Router Hardware Reference for more information on configuring

emulation software.

2. Log in and set the password.

The log in prompt appears on the terminal or PC. If the log in prompt

doesn’t appear, press [Enter] two or three times.

When the router boots for the first time it automatically creates an account

with manager privileges. The account has the log in name “manager” and

the password is “friend”. Passwords are case sensitive.

At the log in prompt, enter the log in name and password.

Password: friend

The router’s command prompt appears and you can now configure the

router using the command line interface.

Change the password as soon as possible. Leaving the manager account with

the default password is a serious security risk. Make sure you remember the

new password as there is no way to retrieve it if it is lost.

Use the following command to change the account password:

set password

To display a list of help topics, enter:

help

To display help on a specific topic, enter:

help topic

Alternatively, type a question mark (?) at the end of a partially completed

command to see a list of valid options.

8AR400 Series Router

C613-04032-01 REV E

See the AR400 Series Router Software Reference for more information on

router start-up and configuration procedures (including a list of message

definitions).

Using the GUI to configure a router:

This section describes how to access the GUI via VLAN1, when the PC and

the router are in the same subnet, in order to configure the router. The

router’s switch ports all belong to VLAN1 by default.

The GUI requires a PC and web browser. Supported browsers are Internet

Explorer 5.0 and greater, or Netscape 6.2.2 or 6.2.3, with JavaScript enabled.

Internet Explorer can be found on the Documentation and Tools CD-ROM

that is bundled with your router.

1. Connect the PC to a router switch port.

The PC can be connected directly, or through your LAN.

To connect the PC directly to the router, use a straight-through Ethernet

cable to connect an Ethernet card on the PC to any one of the router’s

switch ports. Note the PC’s IP address and mask.

To connect via a LAN, use an Ethernet cable to connect the router’s switch

port(s) to the device(s) on the LAN. Connect AR410 and AR410S routers

through port 4 and ensure that the PC/hub switch is pressed in. Select the

LAN PC from which you wish to configure the router. The PC should be in

the same subnet as the part of the LAN that contains the router (for

example, the PC could be connected to a hub or Layer 2 switch that is

directly connected to one of the router’s switch ports). Note the PC’s IP

address and mask.

2. Access the CLI on the router.

Follow the instructions in the previous “Using the CLI to configure a

router” section.

AR400 Series router

Switch Ports

POWER

OFF

RS-232

ETHERNET

3450 WAN1 DMZ ASYN1

ASYN0 CONSOLE

10BASE-T/100BASE-TX SWITCH PORTS

straight-through cable

AR400 Series Router

Switch Ports

Hub or Layer 2

Switch

3421

10BASE-T/100BASE-TX SWITCH PORTS

POWER

OFF POWER

OFF

RS-232

ETHERNET

3450 WAN1 DMZ ASYN1

ASYN0 CONSOLE

10BASE-T/100BASE-TX SWITCH PORTS

Quick Install Guide 9

C613-04032-01 REV E

3. Enable IP.

At the CLI, enter the command:

enable ip

4. Assign an IP address to VLAN1.

Assign the VLAN1 interface an IP address in the subnet that the PC uses,

using the command:

add ip interface=vlan1 ip=ipaddress mask=mask

5. Browse to the GUI.

If you access the Internet through a proxy server, set your browser to

bypass the proxy for the IP address you assigned to the VLAN1 interface.

Point your web browser at the IP address of the VLAN interface.

6. Log in and set the password.

At the log in prompt, enter the log in name and password. Passwords are

case sensitive.

User Name: manager

Password: friend

The system status page appears and you can now use the GUI to configure

the router.

To ensure configuration settings are saved correctly, use the GUI menus and buttons to

navigate, not your browser’s buttons.

As a security precaution, change the password as soon as possible.

To change the password, select Management > Users from the sidebar

menu. Select the Manager account and click Modify.

7. To access context-sensitive help in the GUI.

Click on the Help Button [Help]. The Help button is located at the top of

the sidebar menu or on any popup page.

Connecting the Data Cables

Connecting the router to your network:

1. Connect to the LAN

If you have not already done so, use straight-through Ethernet patch cables

to connect the device(s) on your private network (LAN) to the router’s

switch port(s). By default, all switch ports are members of VLAN1.

10 AR400 Series Router

C613-04032-01 REV E

2. Connect to the DMZ (AR450S)

If you have a public server, use an Ethernet patch cable to connect it to the

AR450S router’s Ethernet DMZ (ETH1) port. Separating public servers

from your LAN allows the firewall to provide greater protection for your

LAN. If you have multiple public servers, you can connect them to a hub

or Layer 2 switch and connect that device to the router’s DMZ port.

3. Connect to the WAN.

If you intend to use a firewall, configure it before you activate the WAN link.

Once initial configuration is complete, use an Ethernet patch cable to

connect the router’s Ethernet WAN (ETH0) port to the Ethernet port of a

WAN device (such as a modem). With AR410 and AR410S routers, you can

instead use a PIC for your WAN connection.

LEDs and What They Mean

LEDs indicate the router’s operational status and port activity.

AR400 Series System LEDs

LED State Function

Power Green The router is receiving power and the power

switch is in the ON position

System Amber The router is malfunctioning

Flashing The fan has failed (AR450S only)

Off Normal operation

Enabled (PIC Bay 0)

(AR410 and AR410S

only)

Green A PIC card is correctly installed and has been

detected by the router

Off No PIC is installed

Full Dup Green The corresponding port is operating at full-

duplex

Off The corresponding port is operating at half-

duplex

Link/ACT Green A link has been established through the

corresponding port

Flashing Data is being transmitted through the

corresponding port

Off No link is present through the corresponding

port

100M Green The corresponding port is operating at

100Mbps

Off The corresponding port is operating at 10Mbps

Altri manuali per AR400 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Allied Telesis Router di rete

Allied Telesis

Allied Telesis AT-FS708LE/PoE Manuale utente

Allied Telesis

Allied Telesis Formula 8200 Manuale utente

Allied Telesis

Allied Telesis AT-GS905 Manuale utente

Allied Telesis

Allied Telesis VPN Manuale utente

Allied Telesis

Allied Telesis IS230-10GP Manuale utente

Allied Telesis

Allied Telesis AT x900-48FS Manuale utente

Allied Telesis

Allied Telesis AT-WR4500 Series Manuale utente

Allied Telesis

Allied Telesis AT-AR240E Manuale utente

Allied Telesis

Allied Telesis AR Router Series Guida all'applicazione

Allied Telesis

Allied Telesis SwitchBlade *8106 Manuale utente

Allied Telesis

Allied Telesis AT-GS950/8 Manuale utente

Allied Telesis

Allied Telesis AT-x310-26FT Manuale utente

Allied Telesis

Allied Telesis AR740 RPS Manuale utente

Allied Telesis

Allied Telesis AR750S-DP Manuale di installazione e funzionamento

Allied Telesis

Allied Telesis AT-AR256E Manuale utente

Allied Telesis

Allied Telesis AT-AR220E Manuale utente

Allied Telesis

Allied Telesis AT-GS950/16 Manuale utente

Allied Telesis

Allied Telesis AT-FSW708 Manuale utente

Allied Telesis

Allied Telesis AT-8550/SP Series Manuale utente

Allied Telesis

Allied Telesis WebSmart AT-FS750/24POE Manuale utente

Allied Telesis

Allied Telesis AT-9408LC/SP Series Manuale utente

Allied Telesis

Allied Telesis SwitchBlade AT-AR440S Manuale utente

Allied Telesis

Allied Telesis AT-8000GS/24POE Manuale utente

Allied Telesis

Allied Telesis AT-FS724L Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza