Allnet ALL8089WPoE Manuale utente
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
ALL8089WPoE
8 Port Web Smart Switch
User’s Manual
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Ver:1.3.3
Web Smart Switch Configure
Please follow the steps to configure this Web Smart switch.
Step 1: Use a twisted pair cable to connect this switch to your PC.
Step 2: Set your PC’s IP to 192.168.2.xx.
Step 3: Open the web browser (like IE…), and go to 192.168.2.1 Then you will see
the login screen.
ID and the password: admin
Step 4: After the authentication procedure, the home page shows up. Select one of
the configurations by clicking the icon.
- Administrator
- Port Management
- VLAN Setting
- Per Port Counter
- QoS Setting
- Security
- Spanning Tree
- Trunking
- Backup/Recovery
- Miscellaneous
- Logout
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Administrator: Authentication Configuration
1. Change the user name and the password.
2. Click “Update” to confirm the new change.
Now, you can use the new user name and the password.
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Administrator: System IP Configuration
1. Change the IP address: type the new IP address or select DHCP IP
configuration.
2. Click “Update” to confirm the new change.
“Update Successfully!!” will be shown on the screen.
3. Click "Reboot" to use new setting to login
Now, the setting of “System IP Configuration” is finished.
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Administrator: System Status
MAC address and system version will be shown on the screen.
1. Change the new comment of this switch by typing the new comment.
2. Click “Update” to confirm the new change.
“Update Successfully!!” will be shown on the screen.
3. Click "Reboot" to use new setting to login
Now, the setting of “System Status” is finished.
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Administrator: Load Default Setting
1. Click “Load” to back to the factory default setting.
**Note: Recover switch default setting excluding the IP address, User name and
Password.
Now, the default is loaded.
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Administrator: Firmware Update
Follow the instruction on the screen to update the new firmware.
Please contact with your sales agents to get the latest firmware information.
Administrator: Reboot Device
1. Click “Confirm” to reboot the device.
Now, the setting of “Reboot Device” is finished.
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Port Management: Port Configuration
Select the “Port No.” - configure the mode below:
1. “Auto” - enable/disable Auto-Negotiation.
2. “Speed” - 10M or 100M mode for the selected port.
2. “Duplex” - Full or Half-Duplex mode for the selected port.
4. “Pause” - enable/disable for the selected port.
5. “Backpressure” - enable/disable for the selected port.
6. “Tx Capability (Cap) ” - enable/disable for the selected port.
7. “Addr. Learning” - enable/disable for the selected port.
Now, the setting of “Port Configuration” is finished.
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Port Management: Port Mirroring
Port Mirroring is used to mirror traffic, RX, TX or TX&RX, from Source port to
Destination port for analysis.
1. Select the Destination port: you can choose port 1 to port 8
2. Select the Source port: by clicking the checking box of the port.
3. Click “Update” to save the setting.
Now, the setting of “Port Mirroring” is finished.
ALL8089WPoE 8 Port Web Smart Switch – User’s Manual
ALLNET GmbH – www.allnet.de
Port Management: Bandwidth Control
1. Select the “Port No.”: you can choose port 1 to port 8
2. “TX Rate Value”: set the transmission rate of the selected port. (0:Full speed;
1~255:Specified bandwidth.)
3. “RX Rate Value”: set the receiving rate of the selected port. (0: Full speed; 1~255:
Specified bandwidth.)
4. “Resolution” : Low: 32 kbps / High: 512 kbps
5. Click “Update” to confirm the setting or “LoadDefault”.
Now, the setting of “Bandwidth Control” is finished.
Altri manuali Allnet Interruttore
Allnet
Allnet ALL-SGI8210PM Manuale utente
Allnet
Allnet ALL8809WMP Manuale utente
Allnet
Allnet ALL-SG4816CW Manuale utente
Allnet
Allnet ALL-SG8205PD Manuale utente
Allnet
Allnet ALL-SG8926PM Manuale utente
Allnet
Allnet ALL-SG8308PM Manuale utente
Allnet
Allnet ALL-SG8826PMX-10G Manuale utente
Allnet
Allnet ALL-SG8428PM Manuale utente
Allnet
Allnet ALL-SGI8108v2 Manuale utente
Allnet
Allnet ALL-SGO8103P Manuale utente
Allnet
Allnet ALL8895 Manuale utente
Allnet
Allnet ALL-SG8910PM Manuale utente
Allnet
Allnet ALL168208 Manuale utente
Allnet
Allnet Synergy 21 S21256 Manuale utente
Allnet
Allnet ALL4806W Manuale utente
Allnet
Allnet ALL8808POE Manuale utente
Allnet
Allnet ALL0484WMP Manuale utente
Allnet
Allnet ALL-SG8310PM Manuale utente
Allnet
Allnet ALL4806W Manuale utente
Allnet
Allnet ALL8845PD Manuale utente
