Allsensor P601 Series Manuale utente

 P601 HART Series                                    

P601 Series HART Protocol

Pressure Transmitter Manual

  HISCO Sensor Institute Inc.

#513~514 HausD biz 10, Seonyu-ro 3-gil Yeongdeungpo-gu, Seoul, Korea

Tel. : 82-2-2284-3737~9,  Fax. : 82-2-2284-3740,   www.allsensor.com

 P601 HART Series                                    

- 1 -

Contents

1. INTRODUCTION

2. SPECIFICATION

3. APPLICATION

4. DISPLAY

5. LOCAL ADJUSTMENT

6. NOTICE

7. ATTACHMENT : CONFIGURATION ADJUSTING SOFTWARE NOTE

 P601 HART Series                                    

- 2 -

1. INTRODUCTION

  P601 with HART pressure transmitter is a SMART pressure measuring unit with 2-wire

analog signal outputs.

It has a good performance with digitally temperature compensation and non-linearity

correction, 4 1/2 digits LCD display with backlight, according with HART communication

protocol, It is available with long-distance operation.

The transmitter can be widely used in pressure measurements and industry process controls

system requiring BUS operation with HART protocol in the fields of petroleum, chemo-industry,

electric power and paper making etc, The unit can be compatible with the similar products

and suitable for applications requiring two wire analog signal transmission or long-distance

adjustment via HART handholding communicator.

Before using P601 transmitter, please read carefully this manual and operating accordingly.

2. SPECIFICATION

2.1 Specification

Input

Pressure Range

0.01 ... 100 MPa

Pressure reference

Gauge, Absolute, Vacuum and Compound

Over Pressure

1.5 x Rated Range or 110 MPa(Min. value is valid)

Media

The liquid or gas which is compatible with STS316L

Output

Output signal

4 ~ 20 mA with HART ® Protocol

Display

4 1/2 LCD Display with Backlight

Electrical specifications

Power supply

12 ~ 36V DC

Load resistance

Max. 500 Ω at 24V

Power ripple

≦500 mV P-P

Reverse polarity

Protected

Response time

(10~90%) ≦ 20 ms

Performance specifications

Accuracy

≦ ±0.25% FSO (±0.1% FSO Option)

Non-linearity

≦ ±0.100% FSO typical ±0.15% FSO

Hysteresis

≦ ±0.100% FSO typical ±0.10% FSO

Long term stability

≦ ±0.1% FSO over 1 Year

Ambient temperature

-20 ~ 40°C

Physical specifications

Process Connection

PT1/2"(Standard), PT1/4", PT3/8" Male Thread

Flange other connections available on request

Materials

Wetted Parts – welded STS316L

Housing – Aluminium Die-casting

Weight

Approx. 1.2kg

Option

Sanitary Diaphragm Seal or Remote Diaphragm Seal

Explosion proof

Ex d IIC T6 (15-GA2BO-0896)

(방호장치 의무안전인증고시 / 고용노동부고시 제 2013-54호, 개정일자 2013. 12. 18)

Enclosure

IP67

 P601 HART Series                                    

- 3 -

2.2 Dimension(mm)

Figure 2-1

3. APPLICATION

3.1 ELECTRICAL CONNECTION

  The Supply/Signal terminal locates inside electronic housing. When making connection,

please open the transmitter cover firstly, the terminal’s definition see as the Figure 3-1, the

left terminal marked with "+" or "–" is for supply/signal.

Figure 3-1

 P601 HART Series                                    

- 4 -

  Power is supplied by the signal wires. The Signal/Supply share one terminal(2 wires, no

additional supply wire). While you make connection, please take very carefully to make

correct connection: the "+"of Supply wires connecting with the "+" of Supply terminal

"+"on the left, signal current "-" out connecting the signal terminal "-" on the center.

  The signal wire to use a shield cable or the twisted-pair couple wire can get the best

effect.

  Please DO NOT let the signal wire share the same wire/cable allocation pipe or slot with

other equipment power supply wires, and the signal wire NOT close to the high-power

equipment. Using sealing element to seal the passing-hole after connecting the wires. In

case you can’t find a sealing element on site, please installing the transmitter with the

wires hole face down to prevent from entering water. The signal wire can be floating on

the ground or any one point in the signal loop grounded. The transmitter housing

grounded or not grounded are both okay.

  The stability of supply voltage for transmitter is not strict, even if the voltage wave

around 1V, the influence on output signal is very small or can be ignored. The transmitter

is capacitive coupled grounded, while you are checking the insulation resistance, take care

NOT use high volts megaohm meter, only max 100V. ㏁ meter can be allowed for

checking the circuits. The maximum current for the transmitter with 4～20mA DC output

will not exceed 22mA DC.

3.2 REMOTE CONTROL

3.2.1 Connecting with the computer

Figure 3-2

  The user can be easily through HART-CONFIG TOOL to connect with HART SMART

pressure transmitter by HART/USB interface to realize the configuration, calibration, local

controls and maintenance of HART protocol SMART pressure transmitter.

 P601 HART Series                                    

- 5 -

3.2.2 Connecting with the hand-hold communicator.

Figure 3-3

  By connecting with MS-H375 HART hand-holder to realize the configuration, calibration,

local controls and maintenance of HART protocol intelligent transmitter.

4. DISPLAY

  Customers can use configuration software to set the volume and the decimal point of LCD

display. Referring to the words of “meter configuration” to “output” of configuration software.

LCD allows the double volumes displaying. The possible setting volume includes current, main

volume and its percentage; every volume is possible to set the decimal position of displaying :

0. 1. 2. 3. If the two displaying volume are same, LCD only displays one; otherwise, LCD will

display the both volumes one after one in 3s internally,

 P601 HART Series                                    

- 6 -

LCD all information display see Figure 4-1

Figure 4-1

Current display see Figure 4-2

Figure 4-2

Main volume percentage display see Figure 4-3

Figure 4-3

Main volume display see Figure 4-4

Figure 4-4

 P601 HART Series                                    

- 7 -

Other display notes:：

Ø In the communication state, the left-up corner of LCD flash 。

Ø For the rooting output, LCD display 。

Ø For fixed current output，LCD display 。

Ø If you start the writing protection，LCD display 。

Ø If you want to let temperature displayed，except the normal display information，LCD

left-down display the temperature“88”，below-19℃ or over 99℃ display .

5. LOCAL ADJUSTMENT

  It is possible to set the unit, range, damp etc and adjust the zero, zero and span elevation

functions, also you can look above volumes to press the keys.

5.1 key operation

  It supports "double keys" and "three keys" operation. (magnetic stick adjustment is same

as double keys pressing operation) In "double keys" operation: Z key is for entering the

volume setting and moving cursor; S key is for entering volume setting, adding and

storing data. In "three keys" operation: Z key is for entering the volume setting and

moving cursor; S key is for entering volume setting, adding and storing data. M key is for

storing data.

5.2 Data Set

  While the left-down corner "88" display 1~7, it shows that the transmitter is in the

state of local adjustment, now you can use keys to input the pass code, adjust data or

elevation. In setting, "S" key is for adjusting data and decimal point, "Z" key is for

moving, "M" key is for storing.

Setting procedure:

  1．Press down "S" key will enter data setting, then symbol starts flashing and you can

change symbol.

  2．If press down S key again, you can exchange data’s "+" and "–"("▲" means "+")

  3．Press down "Z" key, the first number begins to flash; now you can set the number.

If you keep pressing down or pressing down "S" key repeat, the number will display

sequentially.

 P601 HART Series                                    

- 8 -

  4．Press down "Z" key again, you can set the second to the fifth number sequentially,

the way is as the same as the step 3.

  5．After setting the fifth number, press down "Z" key to set the decimal point. Four

decimal points start to flash at the same time and you can set decimal point

position. Now, press down "S" key, the decimal point position change sequentially.

  6．After setting decimal point, press down "Z" key, the left-down arrows flash, now you

can store your setting.

  7．Press down "S" key to store setting; press down "Z" key, symbols bit begins to flash

and you can start the new setting programmed.

Notice: If it is the "three keys" operation, during the setting procedure, you can press

down "M" key at anytime to store setting quickly. If not, you have to wait for the next

down arrows lashing to store your settings.

5.3 Local Adjustment

5.3.1 data setting

    In local adjustment, LCD left-down "88" will show setting data types, the

corresponding relations:

Left-down "88"show

Setting data

0 or null

Normal display

Setting pass code

Setting units

Setting Range Down Limit

Setting Range Up Limit

Setting Damp

Adjusting Main volume to Zero

Zero and Span elevation

    In the normal display state, press down "Z" key will enter the configuration data

setting, configuration

 P601 HART Series                                    

- 9 -

data setting process see Figure 5-1

Figure 5-1

Note:

Ø In double key operation, while "▼" flashes, press down "S" key to realize M key

function.

Ø The pass code of configuration data setting is 00002, when it is correct, you can start

data setting, if not, it will be back to normal display.

Ø If the setting data is over the limitation, LCD display "OVER" , then press down "S"

key or "Z" key to reset.

Ø While entering configuration data setting, if no press down in two minutes, it will be

back automatically.

Ø When finishing the setting and going back the normal display state, if you press down

"Z" key again in ten seconds, it will restart the setting and ignore the pass code

procedure. In 5.2 data setting, you can do the pass code entering, the up and down

range limitation and damp setting, but as for unit setting and main volume setting

zero, you will follow the below procedure:

Indice

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente