Amano TCX-22 Manuale utente

AMANO

TCX-22

Electronic Time Clock

Operation Manual

(1*/ ,6+ n(63 $ f2/



Proprietary Notice

This document contains proprietary information and such information

may not be reproduced in whole or part without the written permission

from Amano Cincinnati, Inc. 140 Harrison Ave., Roseland, New Jersey

07068.

Amano Cincinnati, Inc. reserves the right to make equipment changes

and improvements which may not be reflected in this document. Portions

of this document may have been updated to include the latest hardware

or firmware versión, if applicable.

We recommend that this document be read in its entirety before any

attempt is made to operate the equipment.

Page 1

TCX-22 Amano Cincinnati, Inc.

Specifications

Power Requirements:

For Clock Input: AC16.5V, 60Hz, 0.6A (Max.)

AC100V ± 10%, 50/60HzFor AC Adapter:

AC120V ± 10%, 60Hz

AC230V ± 10%, 50/60Hz

Battery: 12V Sealed Rechargeable Lead-Acid Battery

NP1.2-12 12V 1.2Ah

Ambient Temperature: -10°C to 45°C (14°F to 113°F)

Ambient Humidity: 10% to 90% (non-condensing)

Dimensions: 6 7/8” (175 mm) wide x 8 1/4” (210 mm) high x

6 1/4” (159 mm) deep

Weight: Approximately 5.9 Kg (13 lbs.)

Environment: Indoor use only; dust-free environment. Keep out

of direct sunlight.

External View

Print Button

Analog Clock

Print Window

LCD Display

Printer Platen

and Margin

ustment

Cover Lock

Page 2

TCX-22 Amano Cincinnati, Inc.

Removing the Cover & Packing Material

1. Turn the key clockwise to unlock

the cover.

2. Lift the cover up, then pull

towards you to remove it.

3. Lift the printer block and

removethe spacer.

4. Remove the spacer between the

Ribbon Cartridge and the Printer

Carriage Tab.

5. Reinstall the cover of your unit.

Internal View

LCD Display

Program Buttons

Reset Button

Analog Clock

Ribbon Cartridge

Card Stopper

Adjustment Screw

Printer Platen

Battery Compartment

Page 3

TCX-22 Amano Cincinnati, Inc.

Power Options

The TCX-22 can be powered by either an AC Adapter or a 12 volt

Sealed Rechargeable battery. The Battery Power Switch on the base

enables you to turn the Battery Power ON or OFF. The battery is

equipped to maintain normal operations for 1 week and/or 5000 prints in

the event of an A/C power failure.

Installing the 12 Volt Battery

1. Remove the AC Adapter if equipped

and remove the cover.

2. Lay the unit down clock face up

3. Remove left battery bracket screws

4. Pull out the left battery bracket.

5. Carefully insert the battery with the

positive and negative clips facing

outwards and to the right.

6. Install the left battery bracket

7. Observing polarity, attach the “Red”

Positive female wire harness to the

“Red” (+) Positive male connector on the Battery.

8. Attach the “Black” Negative female harness wire to the “Black” (-)

Negative connector located on the battery.

9. Set the Battery Power to the “Connected” position.

Note: Recharge the battery at least every two weeks or every 5000

prints. The minimum charging time should be 12 hours and the switch

should be turned off when the unit is not in use.

Connecting the AC Adapter

1. Set the Battery Power Switch to the OFF position.

2. Verify that the AC outlet voltage falls in the range of 100-240 Volts

AC. Verify that the cord and plug are appropriate for your AC source.

3. Plug the connector end of the AC Adapter into the Power Connector

and the other end into a properly grounded 120 or 240 Volt outlet.

Page 4

TCX-22 Amano Cincinnati, Inc.

Make a Test Print

1. Make sure that there is power to the TCX-22 (Refer to Page 3).

2. Insert a piece of paper or time card into the TCX-22. The clock will

automatically print YEAR, MONTH, DATE and TIME with AM or PM.

3. If the imprint is satisfactory, the TCX-22 is ready for use.

4. If you wish to change the time and/or print style on the TCX-22, enter

into Program Mode for various print styles. The next page gives

instructions on programming the TCX-22 to fit your needs.

Adjusting the Margin

1. Unlock and remove the

cover.

2. Locate the Card Stopper

Adjustment Screw on the

right side of the clock,

below the printer platen.

3. Position a piece of paper or

time card as desired.

4. Loosen the screw to move

the Card Stopper forward or

back. Tighten the screw as

needed. (See top

illustration.) The print

margin can be adjusted to a

maximum of 7/8” (22 mm).

Page 5

TCX-22 Amano Cincinnati, Inc.

Illuminated Print Option

The TCX-22 is equipped with a feature that allows the print area to

illuminate. The switch is located on the back panel. When connected to

an AC adapter the unit will stay illuminated. When used with a battery, it

illuminates for about 20 minutes every time the LED switch is pressed.

Program Mode Guide

Unlock and remove the cover. Locate the PROGRAM,CHANGE and

ENTER buttons on top of the clock.

The PROGRAM button is used to enter and exit the Program Mode.

Press the PROGRAM button at any time to exit the Program Mode. If a

program step is in the process of being changed when this button is

pushed, the new information will not be saved.

The CHANGE button is used to change the information on the display.

When you are reviewing the main programming menu, use the CHANGE

button to advance to the next programming step. When you are revising

a programming step, use the CHANGE button to change the blinking

information.

The ENTER button is used to accept the information shown on the

display and save it in memory.

The RESET button is located on the right side of the clock. Pressing this

button will clear any jams or errors.

Page 6

TCX-22 Amano Cincinnati, Inc.

Entering the Program Mode

1. Unlock and remove the cover.

Menu Code Menu Function

P1 dA ESets the date

P2 Cloc

Sets the clock time

P3 dLS Disable/Enable Daylight Saving Time

P4 Prn Sets the print style using Quick Print Set-Up

Codes

P5 O hr Accesses Other Options Menu

2. Press and hold the PROGRAM button to access the

MainProgramming Menu. The Main Programming Menu consists of

the Following

3. When P1 dA Eflashes in the display, release the

PROGRAM button. To move to the next menu item,

press the CHANGE button.

Note: If no other button is pressed after five minutes, the clock will

return to the Normal Mode and the clock hands will reset.

Setting the Year, Month and Date

1. When the display flashes P1 dA E, press the ENTER

button.

2. Press the CHANGE button until the correct year

appears, then press the ENTER button.

3. Press the CHANGE button until the correct month

appears, then press the ENTER button.

4. Press the CHANGE button until the correct date

appears, then press the ENTER button.

5. When the display flashes the correct year, month and

date, press the ENTER button.

6. When the display flashes P1 dA E, press the CHANGE

button to move to Setting the Clock Time.

Page 7

TCX-22 Amano Cincinnati, Inc.

Setting the Clock Time

Note: Use a 24 hour and 60 minute format when setting the time. For

example, 2:00 PM = 14:00.

1. When the display flashes P2 CLoc, press the ENTER

button.

2. Press the CHANGE button until the correct hour

appears, then press the ENTER button.

3. Press the CHANGE button until the correct minute

appears, then press the ENTER button.

4. When the display flashes the correct time, press the

ENTER button.

5. When the display flashes P2 CLoc, press the

CHANGE button to move to the Daylight Saving

Time On/Off Setting.

Disabling/Enabling Daylight Saving Time (DST)

Note: When this setting is set to ON, the clock’s time will automatically

change for DST. When this setting is set to OFF, the clock’s time will not

change for DST. The dates to begin and end DST are set in the Other

Options Menu (See Page 14).

1. When the display flashes P3 dLS , press the ENTER

button.

2. Press the CHANGE button to alternate between On

and Off.

3. When the display flashes the correct setting, press

the ENTER button.

4. When the display flashes P3 dLS , press the

CHANGE button to move to the Quick Set-Up Code

setting.

Page 8

TCX-22 Amano Cincinnati, Inc.

The Quick Set-Up Code Setting

Note: If you do not wish to use one of the Quick Set-Up Code settings,

you may set an alternate style on the following page.

1. When the display flashes P4 Prn , press the

ENTER button.

2. The display will flash the current setting. Press the

CHANGE button to scroll through each of the

Quick Set-Up Code Settings.

Code Print Style Print Direction

Pr-1 Day, 24Hr., 100th/Hr Right Side Print

Pr-2 Day, 12Hr., 60th/Hr. Right Side Print

Pr-3 Month, Date, 24Hr., 100th/Hr. Right Side Print

Pr-4 Month, Date, 12Hr., 60th/Hr. Right Side Print

Pr-5 2 Digit Year, Month, Date, 12Hr., 60th/Hr. Right Side Print

Pr-6 4 Digit Year, Month, Date, 12Hr., 60th/Hr. Right Side Print

Pr-7 4 Digit Year, Month, Date, 24Hr., 60th/Hr. Right Side Print

3. When the display flashes the correct setting, press

the ENTER button.

4. When the display flashes P4 Prn , press the

CHANGE button to move to the Other Options

menu.

Accessing the Other Options Menu

1. When the display flashes P5 Oh r, press the

ENTER button.

2. The display will flash the first programming step in

the Other Options sub-menu. Press the CHANGE

button to advance through the menu selections.

Menu Code Menu Function

I1 Prn Set Print Style using Sumbol or Print Style Codes

I2 LAn9

Sets the Language of the print out

IPrdr

Sets the Print Direction (left or right hand)

I4 APr Disable, enable, or configure the Auto print option

I5 2Er0

Diable/enable Leading Zero in print out

I6 bdL Set the date that Daylight Saving Time begins

I7 EdL Set the date that Daylight Saving Time ends

I8 dIA9

Accesses the Diagnostic Rountine

Altri manuali per TCX-22

Indice

Altri manuali Amano Orologio

Amano

Amano 3500 Series Manuale utente

Amano

Amano PIX-10 Manuale utente

Amano

Amano MJR-8000 Series Guida alla risoluzione dei problemi

Amano

Amano PIX-55 Manuale utente

Amano

Amano PIX-21 Manuale utente

Amano

Amano EX3000N Manuale utente

Amano

Amano PIX-3000x Series Manuale utente

Amano

Amano CP-3000 Manuale utente

Amano

Amano PIX-10 Manuale utente

Amano

Amano CP-5000 Manuale utente

Amano

Amano MRX-35 Manuale di istruzioni

Amano

Amano BX-1500 Manuale utente

Amano

Amano TS-3000i Manuale utente

Amano

Amano PIX-75 Istruzioni operative

Amano

Amano MICRODER MR-7000 Series Manuale utente

Amano

Amano PIX-55 Manuale utente

Amano

Amano BX6000 Manuale utente

Amano

Amano PIX-3000x Series Manuale utente

Amano

Amano EX7500 series Manuale utente

Amano

Amano PIX-10 Manuale utente

Amano

Amano Time Partner TCX-11 Manuale utente

Amano

Amano PIX-15 Manuale utente

Amano

Amano TCX-85 Manuale utente

Amano

Amano TCX-22 Manuale utente

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente