Amano 3500 Series Manuale utente
3500/3600 SERIES
Handling Manual
IMPORTANT:
Please do not return this clock to the retailer. If you
have any questions or need assistance, please call us
toll-free at (800) 253-9836.
For more information about Amano’s complete product line,
visit our web site at http://www.amano.com
1. Installing your time clock
1.1
Remove the cover case from the time clock using the key as
shown in Fig. 1. Turn the key all the way to the right and pull
the cover forward. Lift the entire cover straight up and over
the push bar. Remove the packing materials (cardboard tabs
marked remove) from both sides of the inked ribbon spools as
shown in Fig. 2.
1.2. The time clock may be placed on a table or installed on the
wall. To mount the clock on the wall, insert a screw on the
wall through the key-shaped hole at the top of the back plate
of the time clock. Tighten the two screws located on the bot-
tom of the back plate as shown in Fig. 3.
2
2. Setting the time and date
NOTE: Do not touch the clock hands.
Insert a blank time card before you begin to verify the time, month and date.
2.1 SETTING THE TIME: Pull up and hold the red-tipped lever.
Put your finger on the white wheel and push clockwise to the
desired time as shown in Fig. 4. Let go of the red-tipped
lever and white wheel. Insert a time card to make sure that
the time is correct as shown in Fig. 5.
NOTE: A=AM; P=PM
If you’re on AM and need PM, you will need to advance the
white wheel 12 hours.
3
2.2 SETTING THE MONTH: Press down the brass retainer clip
inserted in the MONTH typewheel. This frees up the wheel.
Turn the wheel counterclockwise using the tip of your pen or
pencil (each groove represents one month) until the desired
month shows on the punch as shown in Fig. 6.
NOTE: The month must be advanced every month.
2.3 SETTING THE DATE (1-31): Turn the DATE typewheel coun-
terclockwise using the tip of your pen or pencil (each click
represents one date) until the desired date shows on the
punch as shown in Fig. 7.
NOTE: If the month has 28, 29 or 30 days, you will need to
change the date typewheel to the first of the month.
4
3. Adjusting your clock for Daylight Saving Time
3.1 Beginning of Daylight Saving Time: Advance the time one
(1) hour using the method described in Section 2.1 (SET-
TING THE TIME) on the first Sunday in April every year.
3.2 End of Daylight Saving Time: There are two ways to adjust
your clock for the end of daylight saving time. You can take
the plug out for more than one hour and set the clock to the
correct time using the method described in Section 2.1 (SET-
TING THE TIME). Or, you can advance the time 23 hours
using the method described in Section 2.1 (SETTING THE
TIME) and adjusting the DATE using the method described in
Section 2.3 (SETTING THE DATE).
NOTE: The clock and typewheels should only be adjusted
forward. Reversing the direction of the clock hands and
typewheels will damage the clock.
4. Replacing the ribbon
When the imprint becomes too light, replace the ribbon using the
following procedure:
4.1 Remove the old ribbon spool by pushing the ribbon spool in
the direction of the arrow as shown in Fig. 8. The ribbon
winding ratchet gear will come out with the ribbon spool.
Remove the ratchet gear from the spool before you discard
the old ribbon.
4.2 Insert the ratchet gear into the new ribbon spool. Insert the
ratchet gear marked “L”into the left spool, and the ratchet
gear marked “R” into the right spool as shown in Fig. 9.
5
4.3
Set the inked ribbon spools with ratchet gears into the holes of
the frame diagonally. The inked ribbon must be carefully installed
between the ribbon shield and frame as shown in Fig. 10.
4.4 Turn the ratchet gear to take up the slack in the inked ribbon.
NOTE: New ribbons may be purchased from any dealer listed in
the RECOMMENDED DEALER SERVICE NETWORK LIST
that was enclosed in your time clock box.
6
Specifications
Power supply AC 120V, 60 Hz
Power consumption 0.03A
Ambient temperature -10˚ C ~ 50˚ C (14˚ F ~ 122˚ F)
Humidity 10% ~ 90% (non-condensing)
Clock movement Synchronous motor
Printing Inked ribbon
Imprints Month, Date, Hour & Minute or
Day, Hour & Minute
Dimensions 81⁄4“ (w) x 6“ (d) x 101⁄2“ (h)
(206 mm x 148 mm x 264 mm)
Weight 10.2 lbs. (4.6 kg)
7
© 1996 Amano Cincinnati, Inc. Printed in U.S.A.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Amano Orologio
Amano
Amano PIX-28 Manuale utente
Amano
Amano PIX-55 Manuale utente
Amano
Amano MJR-8500 SERIES Manuale utente
Amano
Amano PIX-75 Istruzioni operative
Amano
Amano CP-5000 Manuale utente
Amano
Amano BX-1600 Guida rapida
Amano
Amano TCX-22 Manuale utente
Amano
Amano PIX-25 Manuale utente
Amano
Amano PIX-25 Istruzioni operative
Amano
Amano TCX-22 Manuale utente
Amano
Amano BX-1500 Manuale utente
Amano
Amano MICRODER MR-7000 Series Manuale utente
Amano
Amano PIX-21 Manuale utente
Amano
Amano EX-3500 Manuale utente
Amano
Amano EX7500 series Manuale utente
Amano
Amano 4700 Series Manuale utente
Amano
Amano BX6000 Manuale utente
Amano
Amano TCX-85 Manuale utente
Amano
Amano EX3000N Manuale utente
Amano
Amano PIX-10 Manuale utente
