AMAZON COMMERCIAL 6000 Count Compact Manuale utente
6000 Count Compact Digital Multimeter, IP67, True rms,
CATIV600V
Multímetro Digital Compacto de 6000 Cuentas,
conTemperatura, IP67, True RMS, CAT IV, 600V
Multimètre Numérique Compact, Indice IP67 de Température,
à Valeur Efficace Vraie, CAT IV 600V, Écran (6000Comptes)
B07W1BL3RH
English . . . . . . . . . . . . . . . . . . . . . . . 3
Español . . . . . . . . . . . . . . . . . . . . . 44
Français . . . . . . . . . . . . . . . . . . . . . 90
3
EN
IMPORTANT
SAFEGUARDS
Read these instructions carefully and
retain them for future use. If this product
is passed to a third party, then these
instructions must be included.
When using electrical appliances, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock, and/or injury to
persons including the following:
WARNING Risk of electric shock! Improper
use of this product can cause damage, shock,
injury or death.
WARNING Risk of electric shock! The safety
features of this product may not protect the user if
not used in accordance with this user manual.
WARNING Risk of electric shock! Take
special care while working under wet conditions.
Humid objects and air have an increased conductivity.
CAUTION Risk of short circuit! Use the test
probe shrouds to avoid accidental short circuiting
if the components or test points are too near each
other. Operation is limited to CAT II applications
when the insulated tips are removed from one
or both test probes. Refer to Specification in this
manual for maximum voltage ratings.
4
EN
WARNING Risk of electric shock! Use
special care when making measurements, if the
voltages are greater than 25V~ rms or 35V .
These voltages are considered a shock hazard.
WARNING Risk of electric shock! Keep
fingers away from the metal probe tips when taking
measurements.
WARNING Risk of explosion! Do not use
the product near explosive vapors, dust or gases.
CAUTION Risk of injury! The probe tips are
sharp for accuracy. Be careful when handling and
reattach the probe tip shrouds after use.
• This product is intended for origin of installation
use and protected, against and the users,
by double insulation per EN61010-1 and
IEC61010-1 2nd edition (2001) to CAT IV
600V and CAT III 1000V; Pollution Degree
2. The product also meets UL 61010-1, 2nd
edition (2004), CAN/CSA C22.2 No. 61010-1
2nd edition (2004), and UL 61010B-2-031, 1st
edition (2003).
• This product must be used by trained
usersonly.
• Do not exceed the maximum allowable input
range of any measurement mode.
5
EN
Mode Maximum Input
A~, A 10 A, 1000V fast acting
fuse (max. 30seconds
every 15minutes)
mA~, mA 800 mA, 1000V fast
acting fuse
V~, V 1000 V~rms/
Frequency, Resistance,
Capacitance, Diode
Test, Continuity
250 V~rms /
Surge Protection: 8 kV peak per IEC 61010
• Do not measure current on a CAT III circuitry
whose voltage exceeds 1000 V.
• Do not measure current on a CAT IV circuitry
whose voltage exceeds 600 V.
• When measuring volts, do not switch to
current/resistance modes.
• Set the function switch to the appropriate
position before measuring.
• Set the function switch to the OFF position
when not in use.
• When changing ranges always disconnect the
connector leads from the circuit under test.
• Inspect the condition of the connector leads
and the product itself for any damage before
operation. Repair or replace any damage
before use.
6
EN
• Verify the product’s proper operation before use
by measuring a known live voltage.
• Always discharge capacitors and remove
power from the device under test before
performing diode, resistance or continuity tests.
• Voltage checks on electrical outlets can
be difficult and misleading because of the
uncertainty of connection to the recessed
electrical contacts. Do not use this product
for checking socket outlets. Use special
equipment for checking socket outlets.
• Do not use, if the product seems to be
damaged or if it is not working properly.
If in doubt, replace the product.
• Comply with all applicable safety codes. Use
approved personal protective equipment when
working near live circuits − especially with
regard to the possibility of arc flash hazards.
• Do not attempt repairs. There are no user
serviceable parts.
• When working in wet conditions, always attach
the rain caps onto the open input jacks.
• Always remove the connector leads before
replacing the battery or fuses.
7
EN
Battery Warnings
• Always insert batteries correctly with regards
to polarity (+ and –) marked on the battery and
the product.
• Exhausted batteries should be immediately
removed from product and properly disposed.
• Keep batteries out of the reach of children.
• Do not dispose of batteries in fire.
• Remove batteries from product if it is not to be
used for an extended period of time.
• If the battery leaks, avoid contact with skin and
eyes. Rinse affected areas immediately with
plenty of clean water, then consult a doctor.
Explanation of Symbols
WARNING The signal word that indicates
a hazard with a medium level of
risk which, if not avoided, could
result in death or serious injury.
CAUTION The signal word that indicates a
hazard that if not prevented could
result in minor or moderate injury.
NOTICE Indicates a practical tip, advice
or practice not related to
personal injury.
8
EN
This symbol, adjacent to another symbol
or terminal, indicates the user must refer
to the manual for further information.
This symbol, adjacent to a terminal,
indicates that, under normal use,
hazardous voltages may be present.
Product is protected by double insulation
or reinforced insulation.
Alternating current (AC).
Direct current (DC).
Earth (ground) terminal/potential.
Fuse
IP67 Product is protected against the effects
of temporary immersion in water.
CAT II
1000V
Product is designed to protect the user
during measurements performed on
circuits directly connected to the low
voltage installation.
CAT III
1000V
Product is designed to protect the user
during measurements performed in the
building installation (up to 1000 V).
CAT IV
600V
Product is designed to protect the user
during measurements performed at the
source of low-voltage installation
(up to 600 V).
9
EN
Intended Use
• This product is intended to perform electrical
measurements on CAT III locations (3-phase
and single phase distribution) and CAT IV
locations (3-phase and single phase primary
over-current protection devices).
• This product covers CAT II and CAT I locations.
• This product may be used only under the
conditions and for the purposes for which it
was designed.
• No liability will be accepted for damages
resulting from improper use or non-compliance
with these instructions.
Before First Use
• Check the product for transport damages.
• Remove all the packing materials.
DANGER Risk of suffocation! Keep
any packaging materials away from children –
thesematerials are a potential source of danger,
e.g. suffocation.
10
EN
Product Description
A
B
C
D
E
F
G
H
I
J
K
L
Indice
Altri manuali AMAZON COMMERCIAL Multimetro
Manuali Multimetro popolari di altre marche
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manuale utente
PeakTech
PeakTech 4000 Manuale per l'uso e la cura
YOKOGAWA
YOKOGAWA 90050B Manuale utente
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manuale utente
Fluke
Fluke 8846A Manuale operativo e di manutenzione
Tempo Communications
Tempo Communications MM200 Manuale utente
