Ambient NanoLockit Guida alla risoluzione dei problemi

QUICK

START

GUIDE

QUICK START GUIDE |

Green Button

Red Button

Micro USB:

charge and

external power

Charge time / operation:

15 min / 5 hrs

30 min / 10 hrs

2 hrs / 35 hrs (full)

ACN Antenna:

for wireless sync

with other Lockits

Lemo Connector:

TC (and metadata)

interface

Status LED

Power Button

Explanation

QUICK START GUIDE |

short

ca. 30 min left

Status LED Codes 1 sec 2 sec

ext. power, idle, charging

ext. power, idle, fully charged

int. power, lo bat

Generator Mode:

idle, no TC out, RTC lost

idle, no TC out, RTC OK

generator set, TC out

generator set, TC out, lo bat

generator set, TC level reduced

TRX Mode:

idle, no TC on input or ACN

TX (LTC/MTC via cable)

RX (LTC/MTC over ACN)

long

LED status overview

QUICK START GUIDE |

The example setup

Film Camera

NANOLOCKIT

DSLR Camera

NANOLOCKIT

Audio Recorder

NANOLOCKIT

TC OUT

TC IN

The goal: syncing

timecode (TC) and

frame rate (FPS).

TC 01:23:45:12

QUICK START GUIDE |

Timecode Cable*

TC-IO-35RA (included)

*NOTE:

The specic cable

required is de-

pendent on the

connected device.

The most common

cables are:

• TC-IO-35RA

• TC-IO

• LTC-Out

• LTC-Out/Epic

Please check our

website.

QUICK START GUIDE |

Press the Power But-

ton on all NanoLockits

for 3 seconds until the

LED lights up green .

Then release and LEDs

start to ash.

Turn on all NanoLockits

NOTE:

To reset the unit to factory default, press

and hold for 10 seconds until LED lights

up red .

3 sec

QUICK START GUIDE |

FPS

12:45:12:02

25 fps

The NanoLockit always starts with its

Real Time Clock (RTC) at last frame rate

or at default 25 FPS with output muted.

To activate the LEMO Output while

jamming other Lockits with this timecode

and frame rate, proceed with step 3.

To adjust the RTC and frame rate,

proceed with step 2A. To jam from an

external device, proceed with step 2B.

QUICK START GUIDE |

To set the RTC and the

frame rate, use the

LockitToolbox software

(PC and Mac, available at

nanolockit.com).

RTC

Set the internal clock of the NanoLockit

micro USB

LockitToolbox

NOTE:

On start a valid RTC will be

indicated by LEDs ashing red/

green , a lost RTC by ashing

red .

QUICK START GUIDE |

micro USB

NANOLOCKIT

TC OUT

TC IN

To jam your NanoLockit

from an external de-

vice, connect them with

the appropriate time-

code cable. If succesful,

the LED will ash green

. Finish by dis-

connecting the cable.

FPS

TC 01:23:45:12

25 fps

External jamming sets the TC

and FPS while activating the

LEMO output.

QUICK START GUIDE |

Press the Green Button

for 3 seconds until LED

double blinks green:

This sets the TC and FPS,

wirelessly syncs all other

NanoLockits, and activa-

tes all LEMO outputs. If

successful, all units will

ash green in sync.

3 sec

TC & FPS

Altri manuali per NanoLockit

Indice

Altri manuali Ambient Telecomando

Ambient

Ambient TOUCH LIGHT Istruzioni operative

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione