Ambirad VISION VSXE20UT Guida all'installazione

ASSEMBLY INSTRUCTION MANUAL

FOR VISION® VSXE

RADIANT TUBE HEATERS

INDEX Section

Introduction & Document Index

Installation Requirements-------------------------------------------------1

Assembly Instructions------------------------------------------------------2

User and Operating Instructions ----------------------------------------3

WARNINGS

AmbiRad equipment must be installed and maintained in accordance with the relevant

provisions of the Gas Safety (Installations and Use) Regulations 1998 for gas fired products.

Due account should also be taken of any obligations arising from the Health and Safety at

Works Act 1974 or relevant codes of practice. In addition the installation must be carried out

in accordance with the current IEE wiring regulations (BS 7671), BS 6896 (Industrial &

Commercial) and any other relevant British Standards and Codes of Practice by a qualified

installer. All external wiring MUST comply with the current IEE wiring regulations.

Document Index.

1 Installation Requirements

1.1 Health & Safety

1.2 Model Definitions

2 Assembly Instructions

2.1 Tools Required

2.2 Assembly Notes

2.2.1 Tubes

2.2.2 Turbulators

2.2.3 Brackets

2.2.3.1 Tube Alignment Sections

2.2.4 U Bends

2.2.5 Couplers

2.2.6 Reflectors

2.2.7 End Caps

2.2.8 Burner Assembly

2.2.9 Heat Exchanger Assembly

2.2.10 Detailed Assembly Drawings

3 User and Operating Instructions

3.3 To Start Heater

3.2 To Switch off Heater

3.3 Routine Maintenance Between Service Intervals

3.4 Frequency of Servicing

1. Installation Requirements.

Isolate any electrical supply to the

heater and controller before proceeding.

Standards and Codes of Practice by a qualified

installer. Isolate all electrical supplies to the

heater & controller before proceeding.

1.2 Model Definitions

VSXE = AmbiRad Vision High efficiency U Tube

heater with forced burner, heat exchanger,

stainless steel reflector and end caps.

1.1 Health and Safety

AmbiRad heaters must be installed in

accordance with the relevant provisions of the

Gas Safety (Installations and Use) Regulations

1998. Due account should also be taken of any

obligations arising from the Health and Safety

at Works Act 1974 or relevant codes of prac-

tice. In addition the installation must be carried

out in accordance with the current IEE wiring

regulations (BS 7671), BS 6896 (Industrial &

Commercial) and any other relevant British

Introduction.

and attention is required to ensure that working

at height regulations are adhered to at the

mounting heights specified.

PLEASE READ this document prior to

installation to familiarise yourself with the

components and tools you require at the various

stages of assembly.

All Dimensions shown are in mm unless

otherwise stated.

The manufacturer reserves the right to alter

specifications without prior notice.

Welcome to the new range of high efficiency

AmbiRad Vision radiant tube heaters. Local

regulations may vary in the country of use and

it is the installers responsibility to ensure that

such regulations are satisfied.

All installation, assembly, commissioning and

service procedures must be carried out by

suitable qualified competent persons

appropriate to the statutory regulations in the

country of use.

When assembling, installing, commissioning

and servicing is undertaken on radiant tube

heaters specified in these instructions, due care

2. Assembly Instructions.

PLEASE READ this section prior to

assembly to familiarise yourself with the

components and tools you require at the

various stages of assembly. Carefully open the

packaging and check the contents against the

parts and check list.

The manufacturer reserves the right to alter

specifications without prior notice.

Please ensure that all packaging is

disposed of in a safe environmentally

friendly way.

For your own safety we recommend the

use of safety boots and leather faced

gloves when handling sharp or heavy items. The

use of protective eye wear is also

recommended.

Pozidrive

Screwdriver

Trestles

Leather

Faced

Gloves

4 & 5mm

Allen

Keys

Tape

Measure

13mm

Socket

Wrench with

Extension

10mm,

12mm &

13mm

Spanners

2.1 Tools Required.

The following tools and equipment are advisable to complete the tasks laid out in this manual.

Suitable alternative tools may be used.

2.2.3 Brackets

There can be three types of brackets supplied

with these heaters:

• Type ‘A’ are suspending brackets with

reflector fixing points.

• Type ‘B’ are suspending brackets with no

fixing points.

• Type ‘C’ is a centre bracket to retain the

reflector. (certain models only)

Slide the bracket assemblies along to the tubes

to the marked positions in their correct order as

detailed in the assembly drawings. Tighten

clamping ‘U’ bolt arrangement to tubes ONLY

WHERE STATED on the assembly drawings.

2.2.3.1 Tube alignment sections For

VSXE50UT Angle Mounted Installations

ONLY.

To allow for differential expansion of the tubes,

a tube alignment assembly is fitted to the first

2.2 Assembly notes.

2.2.1 Tubes

Identify and position tubes on trestles. For

aesthetics it is advisable to position the tube

seam and coupling fastener so that these

cannot be seen from beneath the heater.

For the 50kW U tube only there are

extension radiant tubes. Join these to the

main tube assembly using couplers as detailed

in section 2.2.4

Mark out the position of the bracket centres

from the dimensions shown on the assembly

drawings.

2.2.2 Turbulators (where fitted)

Insert turbulator(s) into tube(s) ensuring the

correct length and quantity are inserted into

their respective correctly identified tube(s) as

detailed in the assembly drawings.

Please read these assembly notes in

conjunction with the correct assembly

drawings (figs 1 to 3).

2.2.7 End Caps

Position the end cap with no tube holes beneath

the reflector profile at the U bend end with the

end cap flanges facing inwards. Fasten to

reflector using M5 pozi set pin and ‘Z’ clip.

Position the end cap with tube holes beneath

the reflector profile at the burner end with the

end cap flanges facing inwards. Fasten to

reflector using M5 pozi set pin and ‘Z’ clip.

2.2.8 Burner Assembly

Slide the burner assembly onto the RIGHT

HAND TUBE when viewed from above,

ensuring it is fully engaged. Secure with grub

screws.

2.2.9 Heat Exchanger Assembly

Slide the heat exchanger assembly onto the

LEFT HAND TUBE when viewed from above

ensuring it is fully engaged. Secure with pinch

screws.

2.2.10 Detailed Assembly Drawings

The following pages show the technical

dimensional details of the VSXE heaters.

Please note the heater type, length and

reference number from the delivery/advice note

before identifying the correct model drawing.

bracket on the fan side radiant tube. Position U

bolt tube alignment sections over the tube and

through bracket prior to clamping.

2.2.4 U Bend.

For VS(A) ‘U’ tube heaters only. Slide the ‘U’

bend onto the tube ends with the clamping

bolts facing upwards until the predefined stop

position. Tighten clamping bolt arrangement

using 13mm socket and wrench.

2.2.5 Couplers.

For VS(A)LF, VS(A)LH, VS(A)LI and VS(A)

45/50UT tube heaters only. For joining radiant

tubes, locate and position tube couplers at the

end of the tubes so that the socket heads are

facing outwards. Tighten clamping bolt

arrangement to secure ensuring the bolts are

not over tightened.

To avoid damaging the heater whilst

installing we recommend the heater

chassis be suspended prior to fitting reflectors.

2.2.6 Reflectors

After removing the protective plastic coating,

slip the reflector through the brackets until the

locating slots are aligned with the type A

bracket fixing points.

Slide the next reflector through the brackets

and overlap the existing reflector until the

locating slots line up with the same bracket

fixing points Secure overlapped reflectors to

bracket using M6 nuts, bolts and flat mud

washers.

All reflectors must be positioned/

attached to the brackets exactly as

detailed in the assembly drawings.

2 x ‘Z’ clips

End Cap

M5 set pin

These holes -

Burner end only

Figure 1. Vision Heater Assembly: Models VSXE U tube 20/25/30kW.

SEE FIGURE 1

FIGURE 1

FIGURE 3

FIGURE 2

Figure 2. Vision Heater Assembly: Models VSXE U tube 35/40/45kW.

SEE FIGURE 1SEE FIGURE 1

FIGURE 1

FIGURE 3

FIGURE 2

Figure 3. Vision Heater Assembly: Models VSXE U tube 50kW.

SEE FIGURE 1SEE FIGURE 1

FIGURE 1

FIGURE 3

FIGURE 2 FROM

3. User & Operating Instructions.

Document reference number GB/VS/153A/0112

AmbiRad Limited Fens Pool Avenue

Brierley Hill West Midlands DY5 1QA

United Kingdom

Telephone 01384 489700

Facsimile 01384 489707

Email [email protected]

Website www.ambirad.co.uk

Technical Support www.s-i-d.co.uk AmbiRad is a registered trademark of AmbiRad Limited. Because of continuous product

innovation, AmbiRad reserve the right to change product specification without due notice

3.1 To Start the Heater

1. Ensure gas supply is turned on.

2. Electrical supply to the controls is on.

3. Ensure that the controls are correctly set

i.e.;

• Clock is correctly set.

• Heater program is correctly set.

• Required room temp is correctly set

4. Once the heating controller ‘calls for heat’

power will be supplied to the heater(s). The

red neon will then illuminate.

5. After a pre-purge period of 10 seconds the

burner will ignite and the amber neon will

then illuminate.

6. If lockout occurs press the lockout reset

button (if available), or switch off electrical

supply and restart after 15 seconds.

7. If lockout occurs three times consecutively

switch off and isolate the gas and electric-

ity supplies.

Call an AmbiRad Service Engineer.

3.2. To Switch Off Heater

1. Switch off electrical supply to the heater.

The burner will stop and the fan will shut

off.

2. If the heater is to be switched off for

periods in excess of one week it is highly

recommended that both the gas and the

electrical supplies are turned off.

3.3. Routine Maintenance between Service

Intervals

After ensuring that the heater is cold and

mains electric isolated, cleaning of the

reflectors with a soft cloth and a mild

detergent (non solvent based cleaners only)

in water can be undertaken.

Additional removal of dust from the radiant

tubes, burner and heat exchanger can be

undertaken.

3.4 Frequency of Servicing

The manufacturer recommends that to

ensure continued efficient and safe

operation of the appliance it is

recommended that the heater is serviced

annually by a competent person e.g. every

year in normal working conditions but in

exceptional dusty or polluted conditions

more frequent servicing may be required.

The manufacturer offers a maintenance

service.

Details are available on request.

For Service requirements, please contact

AmbiRad

For further technical and service support

visit our Support Information Database at

www.s-i-d.co.uk

Altri manuali per VISION VSXE20UT

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ambirad Stufa

Ambirad

Ambirad SmartCom3 Manuale di servizio

Ambirad

Ambirad VISION VSXE20UT Guida utente

Ambirad

Ambirad NRV12LR Manuale di servizio

Ambirad

Ambirad VCH Series Guida utente

Ambirad

Ambirad Vision VPLUS HL120V Manuale di istruzioni

Ambirad

Ambirad Scorpio SC 12 Manuale utente

Ambirad

Ambirad SCA45 Manuale tecnico

Ambirad

Ambirad AIRBLOC ACR Series Manuale utente

Ambirad

Ambirad QUARTZ GLOW Manuale utente

Ambirad

Ambirad Vision Range VSXUS Manuale utente

Ambirad

Ambirad Vision VSXUS 90 Scheda tecnica

Ambirad

Ambirad VISION COMPACT VC40 Guida all'installazione

Ambirad

Ambirad Tornado 600 Guida all'installazione

Ambirad

Ambirad Vision VSO Series Guida all'installazione

Ambirad

Ambirad UCA 25 Manuale utente

Ambirad

Ambirad Vision VSX Manuale utente

Ambirad

Ambirad VSUS Manuale utente

Ambirad

Ambirad SCA 45 Guida

Ambirad

Ambirad AMBIRAD VISION VSX Series Manuale utente

Ambirad

Ambirad Vision Series Manuale utente

Ambirad

Ambirad VCLUS 40-S10 Manuale utente

Ambirad

Ambirad VPlus40 Manuale utente

Ambirad

Ambirad Vision VS Guida utente

Ambirad

Ambirad OFSU32 Istruzioni operative

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente