AMC iLive series Manuale utente
The New iLive series of AMC Wireless systems
Created for active musician and presenters who also manage their own sound, AMC
iLive improves your performance and simplifies your setup.
Innovations such as automatic transmitter setup ma e wireless system management
effortless. iLive wireless microphone system deliver the crystal clear sound quality that
pro audio engineers trust.
CONTENTS:
Receiver features 3
Handheld Transmitter 8
Body pac Transmitter 10
Changing Batteries 11
Operation 13
Troubleshooting 15
Specifications 16
Volume control nob
LCD display
IR window for data transfer to transmitter
Controllers: Press "SET" to enter menu, to navigate menu press “” or “”, to select item
press “SET”. Press and hold “” “” button to select the frequency and channel.
Power button switch: When the Power is switched on, the LCD should be lit, Press and
hold the button for 3 seconds, to turn off the receiver.
AC power supply
Antenna input
XLR balanced audio output
l/4" unbalanced audio output
Audio level switch
8-step level display showing incoming RF signal
8-step level display with “PEAK” warning showing incoming AF signal
When the FREQ light glows, displayed numbers show active frequency.
When the CHAN light glows, displayed numbers show active channel.
Squelch (MUTE) indicator: with the active mute, no signal is transmitted to outputs
Diversity display (shows if antenna I or antenna II is active).
Operating Menu
•
Before turning on the receiver, firstly ensure that the transmitter is switched off, and then
adjust receiver volume to the min.
•
Chec for Audio and Radio frequency decibel meters. If values are high exchange the
channel to avoid the noise spot, it may also increase the static chirp value, enhancement
anti jamming ability.
•
Lastly turn on the transmitter power source, the corresponding channels radio frequency
decibel meter lightens. Adjust receivers audio output level to suitable size, then spea to
the microphone, the receiver audio frequency decibel meter lightens in correspondence
to microphone volume level. If voice output is not hearable and the decibel meter is not
bright, overhaul transmitter and receiver.
Operating Receiver
By using the “” or “” buttons you can directly switch between the factory-preset
frequencies or channels presets. The display starts flashing by indicating that your selection is
active. Press SET button to set selected channel or frequency.
1. Automatic Transmitter setup (IR)
Press "SET" button, The LCD Display should display “PRG IR” as below. Put the
receiver IR window to match the transmitter IR window, and hold for 2-3
seconds, this scans for a clear channel and sets the receiver to that channel.
.
2. Display control
Press "SET" button twice, The LCD Display should display “DISPL” as below.
On the receiver you can choose whether the frequency or the channel number will by
displayed in display. Select the “DISPL” menu by pressing the “SET” button. With the “” or
“” buttons you can choose between: channel number: “CHANNEL” or frequency: “FREQU”
After selection display starts flashing, at this moment press SET button to record your settings.
Press SET button one more time to return the main display.
3. Selecting the requency, channel number
Press SET button so that the following information is displayed (main display)
With the “” or “” buttons you can directly switch between the factory-preset frequencies
(Channels presets). The display starts flashing by indicating that your selection is active. Press
SET button to record your setting.
4. Adjusting the squelch threshold (receivers only)
Select the "SQELCH" in menu by pressing the SET button until "SQELCH" appears on the
display; after a short pause the current squelch setting is displayed. With the “
”
or
“”
you
can select a different setting.
The squelch can be switched of (0 dB) or adjusted in 5 db steps. Selecting a smaller value
reduces the squelch threshold, selecting a higher value increases the squelch threshold. New
setting starts flashing on the display. Set the squelch threshold to the lowest possible value
that suppressed hissing noise. If the squelch threshold is set too high, the transmission
distance will be reduced.
5. Locking and Unlocking Controls
Press SET button until you will see the LCD display as below
You can loc the “ ” buttons to prevent accidental programming during operating.
Activating the Loc -mode function
Select “LOCK” in menu by pressing the “SET” button. Current setting is indicated on the
display. Press “” button to activate the loc -mode function. “LOCK ON” starts flashing on the
display. Press “SET” button to return to the main menu.
Note:
If you press “” / “” buttons, “LOCK” appears on the display informing that the buttons are
now loc ed.
Deactivating loc -mode function
Select “LOCK” in menu by pressing “SET” button. “LOCK ON” appears on the display.
Press ““” / “” buttons to deactivate the loc -mode function (“LOCK OFF” begins to flash on
the display) Press “SET” button to return to the main display. Now all functions can be
operated normally.
Sound inlet bas et
Display section
IR port receives infrared beam to synchronize frequencies
Power on/mute/off
Microphone body
Battery port: 2*1,5 AA Al aline batteries
RF LOW and HIGH switch
LOCK switch
Hand-held transmitter
LCD display showing the channel number
Battery level indicator
Operating Hand-held Transmitter
After switching transmitter’s power on, LCD displays the CHANNEL and BATTERY LEVEL. If
you want to change the active channel, you need change the channel in the receiver first and
then, put the transmitter IR port in front of the receiver and Press SET button to synchronize
frequencies.
Body Pack Transmitter
Microphone Input Jac
On-Off switch
Low battery indicator: When the power is switched "ON", indicator blin one time, for
improving that the battery capacity is normal. When indicator shows no activity unit does not
have power, or the battery was not loaded properly. If the battery indicator lamp is shining, it
shows that the battery is low and needs to be replaced.
Transmitting antenna
LCD Display: Displays current active channel and battery status
Infrared detector (IR port)
Battery holder
Mounting clip
Gain control
Body Pack Transmitter operation
After switching transmitter’s power on, LCD displays the CHANNEL and BATTERY LEVEL. If
you want to change the active channel, you need change the channel in the receiver first and
then, put the transmitter IR port in front of the receiver and Press SET button to synchronize
frequencies.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali AMC Sistema microfonico
Manuali Sistema microfonico popolari di altre marche
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente
Alpha Technologies
Alpha Technologies RBMS Manuale utente
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Manuale utente
Shure
Shure UA844 Manuale utente
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente
Pyle
Pyle PDWM5000 Manuale utente