AMC iLive X2 Manuale utente
iLive X2 – one of the latest wireless microphones systems of the AMC iLive
series. This system is created for active musicians and presenters who also manage
their own sound. iLive X2 improves your performance and simplifies your setup. iLive
X2 - dual wireless microphone system which delivers the crystal clear sound uality
that pro audio engineers trust.
CONTENTS:
Wireless system features 3
Product Introduction
3
System components
4
Front panel
4
Rear panel
5
Receiver LCD Instruction
5
Handheld transmitter
6
Handheld transmitter LCD instruction
6
Body pack transmitter
7
Body pack transmitters LCD instruction
8
Lavalier microphone
8
Headset microphone
8
System settings 9
Receiver setup
9
Handheld microphone setup
10
Body Pack Transmitter setup
11
Operation 12
Troubleshooting
13
Batteries installation 14
Specifications 16
Product Introduction
The iLive X2 dual wireless microphone system is adopted by UHF fre uency
transmission. This system is controlled by mini CPU control which enhances the fre uency
more stable. The working range is 795MHz~820MHz where programmed 100 fre uency
combinations make the channels interchangeable. Advanced audio and noise lock by dual
mute control technology avoids the interruption from any noise signal. The anticipated
decline function of CPU settles the weakness of interval break at the audio output from
working distance of receiver. In this dual wireless microphone are integrated Infrared
Automatic Channel Targeting system, locking function, High and Low modes power’s
transmitter. The main body provides two separated balance outputs of each microphones
and one mixed unbalanced output. These outputs allow very conveniently connect this
microphone with mixers or amplifiers. In this handheld microphone is installed uni ue
software program which controls power-on and power-off. No matter in what situation the
whole system is, there is no shock from accidently power-on and power-off, and therefore the
safety of post amp and speakers is ensured.
System components
All system includes:
Receiver .........................................................................................................................1pc.
1/4 jack audio connecting cable ...................................................................1pc.
Power supply ..............................................................................................................1pc.
Antennas .......................................................................................................................2pc.
User manual ................................................................................................................1pc.
Front panel
A antenna connector Volume control for microphone A
LCD display Infrared automatic fre uency window
Function Buttons Volume control for microphone B
Power on/off Switch B antenna connector
Rear panel
DC power socket Output A s uelch level control
Microphone A audio output Mixed audio output
Microphone B audio output Output B s uelch level control
Receiver LCD Instruction
8-degree RF level display: to display the strength of the received RF signal.
8-degree Audio level display: to display audio signals.
Fre uency menu display: If FREQ lights, then the latter six characters display the current
operating fre uency.
Channel menu display: If CHAN lights, then the display is indicating the current operating
channel.
Mute display: When MUTE lights, then the display is indicating that no radio signals is
being received.
Channel display: dynamically display the current operating channel.
Handheld transmitter
Sound inlet basket
LCD display
IR port : receives infrared beam to synchronize fre uencies
Power on /off/mute switch
Microphone body
Battery port: 2*1,5 AA Alkaline batteries
LOW and HIGH power’s RF switch
LOCK switch
Handheld transmitter LCD instruction
LCD display showing the channel number
Battery level indicator
Body Pack ransmitter
Microphone Input Jack
On-Off switch
Low battery indicator: When the power is switched "ON", indicator blink one time, for
improving that the battery capacity is normal. When indicator shows no activity unit does not
have power, or the battery was not loaded properly. If the battery indicator lamp is shining, it
shows that the battery is low and needs to be replaced.
Transmitting antenna
LCD Display: Displays current active channel and battery status
Infrared detector (IR port)
Battery holder
Mounting clip
Gain control
Body Pack ransmitter’s LCD instruction
LCD display showing the channel number
Battery level indicator
Lavalier microphone
Microphone
Microphone clip
Mini XLR
Microphone windscreen
Before use please, fix Lavalier microphone to the lapel or tie where suitable place for sound
pick-up is. Plug the mini XLR into the microphone input on body pack transmitter. Now you
can start using this device.
Headset microphone
Microphone
Gooseneck
Neck - frame
Mini XLR
Before use please, put the neck frame behind your neck and fix about 2 – 5cm distance
between mouth and microphone. Plug the mini XLR into the microphone input on body
pack transmitter. Now you can start using this device.
Receiver setup
1. Before turning on the receiver, please turn off the transmitters and turn the receiver’s
volume knobs down to the smallest volume.
2. If you want turn on/off the receiver, please push the POWER button for 3 seconds.
3. After transmitters turning on, the corresponding RF level will be illuminated on the LCD.
Now you can adjust receiver's volume to a proper level and make some sounds towards
microphone. During this, receiver’s audio level meter should illuminate signal of your voice. If
audio output or RF level meters are not illuminated, please examine the device.
4. If RF or audio signals level meters show signals unstable, please change the receiver
channel. Maybe interference causes is the problem. If you want to avoid the unstable work,
don’t use both microphones in the same channel at one time.
5. Press SET button to select the main menu one by one in a cycle. Press " ^ " or " v " buttons
to change the current state of the selected menu. Hold the " ^ " or " v " button for a long time
to uickly select the fre uency or channel.
After parameters’ changes, LCD screen will be flashing as a reminder in 2-3 seconds, and the
flashing will be stopped after pressing SET button one more time. After this procedure your
settings will be confirmed.
6. For Automatic Fre uency Operation press SET button. After pressing, main display became
as in the picture1. Target transmitter IR port in to receiver’s infrared automatic fre uency
window and hold it for 2-3 seconds. Receiver’s channel parameters shall be sent to
transmitters via infrared date.
Picture 1 Picture 2
7. For the main display settings press the SET button several times until LCD screen becomes
like in picture 2. You can change LCD display by pressing " ^ " or " v ". If you choose
"CHANNEL", then you will see channel number on the main display field. If you choose
"FREQU", then you will see the actual working fre uency on the main display. After settings,
please press SET button again for the confirmation.
8. For the System Locking Control press the SET button for several times until you will see the
LCD screen as in picture 3.
After 2 -3 seconds the pictures, "LOC ON“ or "LOC OFF " will appear on the position of
"LOCK“. LOCK status can be changed by pressing " ^ " or " v " buttons.
After changes please push SET button one more time to confirm the settings. (Note: This
Control function is for locking receiver’s current working status. If the locked state is "LOC ON",
it is unable to change the current operating status, if it is the non -locked state "LOC OFF" , all
the menu functions can be changed.)
Picture 3
Handheld microphone setup
1. Before starting, please open the battery cover and insert 2AA alkaline batteries.
2. Slide the transmitter ON/MUTE/OFF switch to the ON position. LCD displays the CHANNEL
and BATTERY LEVEL.
3. If you want to change the active channel, you need to change the channel into the
receiver and set receivers menu status as in picture1. After this, target transmitter’s IR port in
to receiver’s infrared automatic fre uency window, after couple seconds channel will be
changed.
4. Slide the transmitter ON/MUTE/OF switch to the MUTE position, if the wireless system
should be used in silent mode. Please note that the microphone is still consuming power
when it is muted.
5. If “ Lo bat” text appears in the microphone display, it shows that the battery is low and
needs to be replaced.
6. When you are finished using the transmitter, switch off the power source. Remove the
batteries when storing for long time.
Indice
Altri manuali AMC Sistema microfonico
Manuali Sistema microfonico popolari di altre marche
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente
Alpha Technologies
Alpha Technologies RBMS Manuale utente
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Manuale utente
Shure
Shure UA844 Manuale utente
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente
Pyle
Pyle PDWM5000 Manuale utente