American Dynamics SpeedDome Ultra VII EIS Manuale utente

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 1 of 15

SpeedDome®Ultra VII EIS

Day/Night Camera Dome

Configuration Utility

Operator’s Manual Supplement

Contents

About this Supplement.......................................... 1

SpeedDome Ultra VII EIS Features...................... 1

Menu Programming Navigation............................. 2

Setting Up EIS....................................................... 2

Changing Camera Functions within Presets......... 3

Return to Auto After Calling a Preset.................... 4

Programming Sequences...................................... 4

Pattern Options: Fixed or Variable Speed............. 7

Recording Patterns When Configured for 16........ 7

DirectSet Menu......................................................8

SpeedDome VII with EIS Compatibility...............10

Specifications-Indoor Dome................................ 13

Specifications-23X Camera with EIS ..................14

Declarations ........................................................ 15

About this Supplement

This supplement provides detailed information

about SpeedDome Ultra VII with EIS (Electronic

Image Stabilization) camera dome features that are

not currently covered in your operator’s manual.

This supplement supports information found in the

Day/Night Camera Dome Configuration Utility

Operator’s Manual, 8200-0184-04.

NOTE: Keep this supplement with your operator’s

manual for reference purposes.

If you need assistance...

Contact your Sales Representative.

SpeedDome Ultra VII EIS

Features

EIS (Electronic Image Stabilization) technology

works to overcome unsteady or blurred video

images from camera movement caused by wind,

vibration, and similar conditions.

The SpeedDome Ultra VII with EIS provides the

following features with firmware version 0710-

0532-0202 and newer.

•Electronic Image Stabilization

•16 Sequences

•Up to 16 Patterns

•Ability to change camera functions for each

Preset.

Updated information is also provided for

SensorNet, RS-422, Manchester, and UTC matrix

switchers and controllers.

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 2 of 15

Menu Programming

Navigation

The SpeedDome Ultra VII with EIS is programmed

from on-screen menus that are accessible through

your controller (keyboard, virtual keyboard, or

Touch Tracker®).

The starting point for programming is the

Configuration Menu. To access the menu on

most controllers press and hold the following

buttons in sequence:

Iris Open > Focus Far > Zoom Out

(Consult your keyboard manual for instructions if

you are unable to access programming menu.)

When programming dome functions, the primary

methods of navigation, item selection, and value

increases or decreases are:

Joystick. The joystick allows you to move the

cursor—represented by highlighting—around the

menus. You can select a field when it is

highlighted.

Focus Far button. Pressing the Focus Far button

selects or enables a choice on a highlighted field.

Zoom In/Out button. Pressing the Zoom In/Out

button scrolls a pre-determined list of values either

up or down in a highlighted field.

Setting Up EIS

You can turn off EIS or adjust the EIS sensitivity

level for all SpeedDome VII EIS cameras on your

system through the Camera Functions screen.

Follow the steps below:

1. Access the Dome Configuration Menu

(Figure 1) by pressing Iris Open, Focus Far

and Zoom Out on your controller.

Figure 1

2. Use the joystick to highlight Camera

Functions and press Focus Far to select. The

Camera Functions screen appears (Figure 2).

Figure 2

3. Make your desired changes. EIS settings

provide the following choices:

•10 Hz = Default setting designed to stabilize

the dome when unwanted dome movements

are at 10 Hz.

•5 Hz = Designed to stabilize the dome when

unwanted dome movements are at 5 Hz.

•Off = Turns off Electronic Image

Stabilization.

For further details on the Camera Functions

screen, consult Chapter 3 of the Day/Night

Camera Dome Configuration Utility Operator’s

Manual, 8200-0184-04.

DOME CONFIGURATION MENU

PAN / TILT / ZOOM / SYNC OPTS

CAMERA FUNCTIONS

ALARMS / AREAS / PRESETS / PZ

ON-SCREEN TEXT DISPLAY

LANGUAGE / PASSWORD

DOME INFORMATION

RESET TO FACTORY SETTINGS

QUIT WITHOUT SAVING

EXIT AND SAVE CHANGES

CAMERA FUNCTIONS

Auto White Bal ON

IR MODE Auto Low

EIS 10 Hz

AGC/Shutter Max Gain Limit

Open Shutter 28 dB 1/4 s

RESET TO FACTORY SETTINGS

EXIT

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 3 of 15

Changing Camera Functions

within Presets

When Presets are created, they adopt the dome

parameters defined in the Camera Functions

screen. You can now customize camera functions

for each Preset by accessing the Camera

Functions screen from the Preset screen.

Note: If you change the parameters in the Camera

Functions Menu for an existing Preset, you will

need to reprogram the Preset to save the changes.

Follow the steps below to change camera functions

with Presets:

1. Access the Dome Configuration Menu

(Figure 3) by pressing Iris Open, Focus Far

and Zoom Out on your controller.

Figure 3.

2. Use the joystick to highlight Alarms / Areas /

Home / Presets / PZ and Press Focus Far to

select. The Alarms / Areas / Home / Presets /

PZ screen appears (Figure 4).

Figure 4.

3. Use the joystick to highlight Presets and press

Focus Far to select. The Select Preset To

Program screen appears (Figure 5).

Figure 5.

4. Use the joystick to highlight the PRESET

NUMBER field and press the Zoom In/Out

button until your desired Preset number

appears.

5. Use the joystick to highlight Camera Functions

and press the Focus Far button. The Camera

Functions screen appears (Figure 6).

Figure 6.

6. Make your desired changes. EIS settings

provide the following choices:

•10 Hz = Default setting designed to stabilize

the dome when unwanted dome movements

are at 10 Hz.

•5 Hz = Designed to stabilize the dome when

unwanted dome movements are at 5 Hz.

•Off = Turns off Electronic Image

Stabilization.

DOME CONFIGURATION MENU

PAN / TILT / ZOOM / SYNC OPTS

CAMERA FUNCTIONS

ALARMS / AREAS / PRESETS / PZ

ON-SCREEN TEXT DISPLAY

LANGUAGE / PASSWORD

DOME INFORMATION

RESET TO FACTORY SETTINGS

QUIT WITHOUT SAVING

EXIT AND SAVE CHANGES

ALARMS/AREAS/HOME/PRESETS/PZ

SET ALARM ACTIONS

SET ALARM STATES

SET HOME POSITION

SET NORTH POSITION

AREA BOUNDARIES

PRIVACY ZONES

PRESETS

SCAN LIMITS

EXIT

SELECT PRESET TO PROGRAM

PRESET PRESET NAME

NUMBER

1-96 PRESET 1-96

SEQUENCE SETUP MENU

CAMERA FUNCTIONS

FOCUS FAR to program preset

EXIT

CAMERA FUNCTIONS

Auto White Bal ON

IR MODE Auto Low

EIS 10 Hz

AGC/Shutter Max Gain Limit

Open Shutter 28 dB 1/4 s

RESET TO FACTORY SETTINGS

EXIT

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 4 of 15

7. Use the joystick to highlight EXIT and press

the Focus Far button to select. The Select

Preset to Program screen appears.

8. Program (or reprogram) the Preset by

selecting FOCUS FAR to program preset (see

Note above).

For further details on the Camera Functions

screen, consult Chapter 3 of the Day/Night

Camera Dome Configuration Utility Operator’s

Manual, 8200-0184-04.

Note: Camera Function settings carry forward

from the last Preset created to the next Preset

created. You can change these settings on the

next Preset when creating the next Preset.

Return to Auto After Calling a

Preset

When calling a Preset, the SpeedDome Ultra VII

EIS camera adopts the IR Mode and EIS setting

uniquely created for that Preset. When an operator

moves the dome from its Preset position, the dome

can return to global IR Mode and EIS settings only

if programmed to do so through the Return to

Auto screen.

Follow the steps below to program Return to Auto:

1. Access the Dome Configuration Menu

(Figure 7) by pressing Iris Open, Focus Far

and Zoom Out on your controller.

Figure 7

2. Use the joystick to highlight Pan / Tilt / Zoom /

Sync Opts and Press Focus Far to select.

The Pan / Tilt / Zoom / Sync Opts screen

appears (Figure 8).

Figure 8

3. Use the joystick to highlight Return to Auto and

Press Focus Far to select. The Return to Auto

screen appears (Figure 9).

Figure 9

4. Use the joystick to highlight each field (Focus,

Iris, EIS, and IR Mode). Select either On of Off

as your global camera default setting for each

field.

5. Use the joystick to highlight EXIT and press

Focus Far to select. When you reach the Dome

Configuration Menu, highlight EXIT AND SAVE

CHANGES and press Focus Far.

Note: the Reset to Factory Settings field resets

only the fields on the Return To Auto screen.

Programming Sequences

A Sequence is a sequential display of multiple

camera Presets. Sequences provide a methodical

and effective way to monitor multiple areas of

interest by switching to different Presets

automatically. Sequences are programmed from

the Select Preset to Program screen.

DOME CONFIGURATION MENU

PAN / TILT / ZOOM / SYNC OPTS

CAMERA FUNCTIONS

ALARMS / AREAS / PRESETS / PZ

ON-SCREEN TEXT DISPLAY

LANGUAGE / PASSWORD

DOME INFORMATION

RESET TO FACTORY SETTINGS

QUIT WITHOUT SAVING

EXIT AND SAVE CHANGES

PAN / TILT / ZOOM / SYNC OPTS

PROPORTIONAL FLIP OFF

1ST ZOOM STOP X 35

MAX TOTAL ZOOM X 92

LINE LOCK ON

FREEZE-FRAME OFF

RETURN TO AUTO

RESET TO FACTORY SETTINGS

EXIT

RETURN TO AUTO

FOCUS ON/OFF

IRIS ON/OFF

EIS ON/OFF

IR MODE ON/OFF

RESET TO FACTORY SETTINGS

EXIT

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 5 of 15

Sequences are created by identifying Preset views

to include in the Sequence and specifying a dwell

time that controls how long each Preset remains on

screen before switching to another Preset. You can

create up to 16 Sequences, each with 16 steps

(Presets).

Steps to Programming

Sequences

Follow the steps below to program Sequences.

1. Access the Dome Configuration Menu

(Figure 10.) by pressing Iris Open, Focus Far

and Zoom Out on your controller.

Figure 10.

2. Use the joystick to highlight Alarms / Areas /

Home / Presets/PZ and Press Focus Far to

select. The Alarms / Areas / Home / Presets /

PZ screen appears (Figure 11.).

Figure 11.

3. Use the joystick to highlight Presets and press

Focus Far to select. The Select Preset to

Program screen appears (Figure 12.).

Figure 12.

4. Use the joystick to highlight Sequence Setup

Menu and press Focus Far to select. The

Sequence Setup Menu screen appears

(Figure 13.).

Figure 13.

5. Use the Joystick to highlight the SEQUENCE

NUMBER field. Press Zoom In/Out to change

values (1-16).

6. Use the joystick to highlight the STEP field.

Press Zoom In/Out to scroll through available

steps. Steps are displayed in groups of 1-4, 5-

8, 6-12, and 13-16.

7. Use the joystick to highlight the PRESET field

and press Zoom In/Out until the desired

Preset number appears (1-96).

8. Use the joystick to highlight the DWELL TIME

MIN field and press Zoom In/Out until the

number of minutes you want the Preset to

remain on screen appears (0-10 minutes).

9. Use the joystick to highlight the DWELL TIME

SEC field and press Zoom In/Out until the

number of seconds you want the Preset to

remain on screen appears (0-60 seconds in

10-second increments).

10. Repeat steps 7 through 9 above until the first

four presets have been selected for steps 1-4.

DOME CONFIGURATION MENU

PAN / TILT / ZOOM / SYNC OPTS

CAMERA FUNCTIONS

ALARMS / AREAS / PRESETS / PZ

ON-SCREEN TEXT DISPLAY

LANGUAGE / PASSWORD

DOME INFORMATION

RESET TO FACTORY SETTINGS

QUIT WITHOUT SAVING

EXIT AND SAVE CHANGES

ALARMS/AREAS/HOME/PRESETS/PZ

SET ALARM ACTIONS

SET ALARM STATES

SET HOME POSITION

SET NORTH POSITION

AREA BOUNDARIES

PRIVACY ZONES

PRESETS

SCAN LIMITS

EXIT

SELECT PRESET TO PROGRAM

PRESET PRESET NAME

NUMBER

1-96 PRESET 1-96

SEQUENCE SETUP MENU

CAMERA FUNCTIONS

FOCUS FAR to program preset

EXIT

SEQUENCE SETUP MENU

SEQUENCE NUMBER 1

STEP 1-4 DWELL TIME

STEP PRESET MIN / SEC

1 1 0 0

2 1 0 0

3 1 0 0

4 1 0 0

EXIT

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 6 of 15

If more Presets are desired in the Sequence,

use the joystick to highlight the STEP field and

press Zoom In/Out to display steps 5-8, 6-12

or 13-16. Add the Preset selection to fill each

step.

11. When finished, use the joystick to highlight

EXIT and press Focus Far to select.

12. At the Dome Configuration Menu screen,

highlight EXIT AND SAVE CHANGES and

press Focus Far to save.

Note: When a zero is encountered in the Preset

column, the Sequence will stop incrementing and

return to Step 1.

Running Sequences 1-16

Two options are available for running Sequences:

•Option 1 – If your keyboard supports the

DirectSet command, you can use it to run a

Sequence immediately (see DirectSet Menu,

page 8). Consult your keyboard manual for

information on DirectSet functions.

•Option 2 - Use the Set Home Position method

to schedule one Sequence to run when the

dome returns to its home position (after a

defined period of inactivity).

Follow the steps below to run Sequences from the

Set Home Position screen:

1. Access the Dome Configuration Menu

(Figure 14.) by pressing Iris Open, Focus Far

and Zoom Out on your controller.

Figure 14.

2. Use the joystick to highlight Alarms / Areas /

Home / Presets / PZ and Press Focus Far to

select. The Alarms / Areas / Home /

Presets/PZ screen appears (Figure 15.).

Figure 15.

3. Use the joystick to highlight Set Home

Position and press Focus Far to select. The

Set Home Position screen appears

(Figure 16.).

Figure 16.

4. On the highlighted ACTION field, press the

Zoom In/Out button until Sequence appears.

5. Use the joystick to highlight the number field.

Press the Zoom In/Out button until your

desired Sequence number appears.

6. Use the joystick to highlight the RETURN TIME

MINS field. Press the Zoom In/Out button to

specify when the dome is to return to its home

position after a period of inactivity (1-60 min.).

This will trigger the Sequence to run.

7. Use the joystick to highlight the EXIT field and

press Focus Far to select.

8. Continue to exit until completely out of all

programming menus.

Note: If a Preset or a Pattern is called by either an

alarm or motion detection while a Sequence is

running, the Sequence will be interrupted.

DOME CONFIGURATION MENU

PAN / TILT / ZOOM / SYNC OPTS

CAMERA FUNCTIONS

ALARMS / AREAS / PRESETS / PZ

ON-SCREEN TEXT DISPLAY

LANGUAGE / PASSWORD

DOME INFORMATION

RESET TO FACTORY SETTINGS

QUIT WITHOUT SAVING

EXIT AND SAVE CHANGES

ALARMS/AREAS/HOME/PRESETS/PZ

SET ALARM ACTIONS

SET ALARM STATES

SET HOME POSITION

SET NORTH POSITION

AREA BOUNDARIES

PRIVACY ZONES

PRESETS

SCAN LIMITS

EXIT

SET HOME POSITION

ACTION SEQUENCE 1

RETURN TIME MINS 10

EXIT

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 7 of 15

Pattern Options: Fixed or

Variable Speed

A Pattern is a series of programmed pan/tilt/zoom

dome movements. The SpeedDome Ultra VII with

EIS allows you to create fixed speed or variable

speed Patterns (variable speed Patterns are

dependent on system capability).

The SpeedDome Ultra VII with EIS provides three

options when configuring the system for Patterns:

Setting Description

Off Allows programming of three fixed speed

Patterns. The three Patterns are limited

to a total of 99 pan/tilt/zoom movements

(e.g., if one Pattern uses 50 movements,

the remaining two Patterns are limited to

a total of 49 movements). Note: The

VM96 system only supports the OFF

setting.

3Allows programming of three variable

speed Patterns. Each Pattern can have

up to 99 pan/tilt/zoom movements.

16 Allows programming of 16 variable

speed Patterns. Each Pattern can have

up to 99 pan/tilt/zoom movements.

Use the following steps to configure the dome for

Patterns:

1. Enter the Dome Configuration Menu

(Figure 17.) by pressing Iris Open, Focus Far

and Zoom Out on your controller.

Figure 17.

2. Use the joystick to highlight On-Screen Text

Display and press Focus Far to select. The

On-Screen Text Display screen appears

(Figure 18.).

Figure 18.

3. Use the joystick to highlight the PATTERN

SELECT field and press Zoom In/Out to select

Off, 3, or 16.

4. Use the joystick to highlight EXIT and press

Focus Far to select. The Dome Configuration

Menu appears.

5. Use the joystick to highlight EXIT AND SAVE

CHANGES and press Focus Far to save.

Recording Patterns When

Configured for 16

Recording Patterns when the Pattern Select field

is set for Off, 3, or 16 is accomplished through

keyboard commands (consult your keyboard’s user

guide). However, additional steps are required

when the Pattern Select field is set for 16.

Follow the steps below to record 16 variable speed

Patterns:

1. Enter the appropriate keyboard commands to

record a Pattern, using 1, 2, or 3 as your

Pattern number (Consult your keyboard user

guide for specific steps.). The Pattern Select

screen appears (Figure 19.)

Figure 19.

DOME CONFIGURATION MENU

PAN / TILT / ZOOM / SYNC OPTS

CAMERA FUNCTIONS

ALARMS / AREAS / PRESETS / PZ

ON-SCREEN TEXT DISPLAY

LANGUAGE / PASSWORD

DOME INFORMATION

RESET TO FACTORY SETTINGS

QUIT WITHOUT SAVING

EXIT AND SAVE CHANGES

ON-SCREEN TEXT DISPLAY

STATUS DISPLAY OFF

DISABLE ALL NAMES? YES

DIAGNOSTIC DISPLAY OFF

DIRECTION INDICATOR OFF

PATTERN SELECT 16

NAME CONFIGURATION MENU

TEXT ATTRIBUTE OPTIONS

EXIT

PATTERN SELECT

1 5 9 13

1 6 10 14

3 7 11 15

4 8 12 16

EXIT

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 8 of 15

2. Use the joystick to highlight a desired Pattern

number (1-16). Press Focus Far to continue.

3. Pan/tilt/zoom the dome as desired for the

Pattern.

4. Execute the keyboard’s Pattern save

command to save the Pattern.

Running 16 Patterns

When a dome is configured for 16 Patterns,

running a Pattern requires displaying the Pattern

Select screen (Figure 19). Follow the steps below

to run a Pattern.

1. Enter the appropriate keyboard command to

run Patterns 1, 2, or 3. The Pattern Select

screen appears.

2. Move the joystick to highlight the desired

Pattern number (1-16) to run.

3. Press Focus Far to select. The Pattern Select

screen disappears and the Pattern runs.

DirectSet Menu

The DirectSet Menu provides easy access to

commonly used SpeedDome Ultra VII with EIS

features when used with compatible controllers.

This allows you to change or activate features

without starting the dome configuration menu. See

the following examples of the DirectSet menu

(Figure 20).

Figure 20: Day/Night Camera Dome DirectSet

Menu (4 screens)

To access a feature on the menu, enter the

number and press the DirectSet button (varies by

controller). Table 1 provides a description of the

available options.

0 TOGGLE DIRECT SET MENU

1 DOME CONFIG MENU

2 AUTO IRIS/AUTO FOCUS

3 FLIP

4 PEEL PATTERN

10 NIGHT MODE

11 DAY MODE

12 AUTO DAY/NIGHT MODE

15 SMOOTH SCAN

16 STEPPED SCAN

FOCUS FAR = next page

17 RANDOM SCAN

20 DOME INFORMATION

48 EIS OFF

49 EIS 5 HZ

50 EIS 10 HZ

51 SEQUENCE 1

52 SEQUENCE 2

53 SEQUENCE 3

54 SEQUENCE 4

55 SEQUENCE 5

Use FOCUS to select next page

56 SEQUENCE 6

57 SEQUENCE 7

58 SEQUENCE 8

59 SEQUENCE 9

60 SEQUENCE 10

61 SEQUENCE 11

62 SEQUENCE 12

63 SEQUENCE 13

64 SEQUENCE 14

65 SEQUENCE 15

Use FOCUS to select next page

66 SEQUENCE 16

FOCUS NEAR = previous page

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 9 of 15

Table 1: DirectSet Menu Options

Command Description

0+DirectSet Toggle DirectSet Menu: Toggles

between displaying and hiding

the DirectSet menu.

1+DirectSet Dome Config Menu: Displays the

SpeedDome Ultra configuration

menu.

2+DirectSet Auto Iris/Auto Focus: Resumes

Auto Focus/Auto Iris mode.

3+DirectSet Flip: Rotates the SpeedDome

180° from its current pointing

direction. This is the same as

pressing the Flip button on

compatible controllers.

4+DirectSet Peel Pattern: Runs the default

Apple Peel Pattern. This is the

same as pressing the Peel button

on compatible controllers.

10+DirectSet Night Mode: Sets the dome IR

mode setting to ON. The dome

switches to full-time black-and-

white (B/W) mode.

11+DirectSet Day Mode: Sets the dome IR

mode setting to OFF. The dome

switches to full-time color mode.

12+DirectSet Auto Day/Night Mode: Resumes

the most recently selected

automatic IR mode setting.

•Auto High: B/W mode activates

~30 lux.

•Auto Mid: B/W mode activates

~3 lux.

•Auto Low: B/W mode activates

~ 0.5 lux

15+DirectSet Smooth Scan: Initiates a smooth

360° clockwise rotation around

the dome axis using the current

tilt, zoom and focus settings.

Command Description

16+DirectSet Stepped Scan: Initiates a

clockwise rotation around the

dome axis pausing briefly every

10° (at 1x zoom) for 3 seconds

using the current tilt, zoom and

focus settings.

17+DirectSet Random Scan: Initiates a

clockwise or counter-clockwise

rotation around the dome axis

using the current tilt, zoom and

focus settings. The dome pauses

randomly as it rotates around the

axis.

20+DirectSet Dome Information: Displays the

Dome Information screen

available through the dome

configuration menu.

48+DirectSet Turns off Electronic Image

Stabilization.

49+DirectSet Sets Electronic Image

Stabilization sensitivity at 5 hz.

50+DirectSet Sets Electronic Image

Stabilization sensitivity at 10 hz.

51+DirectSet Sequence: Runs Sequence 1

52+DirectSet Sequence: Runs Sequence 2

53+DirectSet Sequence: Runs Sequence 3

54+DirectSet Sequence: Runs Sequence 4

55+DirectSet Sequence: Runs Sequence 5

56+DirectSet Sequence: Runs Sequence 6

57+DirectSet Sequence: Runs Sequence 7

58+DirectSet Sequence: Runs Sequence 8

59+DirectSet Sequence: Runs Sequence 9

60+DirectSet Sequence: Runs Sequence 10

61+DirectSet Sequence: Runs Sequence 11

62+DirectSet Sequence: Runs Sequence 12

63+DirectSet Sequence: Runs Sequence 13

64+DirectSet Sequence: Runs Sequence 14

65+DirectSet Sequence: Runs Sequence 15

66+DirectSet Sequence: Runs Sequence 16

255+DirectSet Admin: Reset Dome (Baxall)

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME CONFIGURATION UTILITY 8200-0184-13, REV. A

OPERATOR’S MANUAL SUPPLEMENT 10 of 15

SpeedDome VII with EIS Compatibility

Controller Generator/Converter Protocol Presets Patterns Camera

Range

AD2091 Manchester 64

AD2083-02B RS-422 (Duplex) 16

AD1024/MP1024 AD2083-02C (AD2083-

02B ver 11YB) RS-422 (Simplex/Duplex) 60

16 1-1024

None Manchester 64

AD2083-02B RS-422 (Duplex) 16

AD1650 AD2083-02C (AD2083-

02B ver 11YB) RS-422 (Simplex/Duplex) 60

16 1-128

Manchester

SensorNet

CCM

RS-422 (Duplex)

1-180

AD2091 Manchester

AD2083-02B RS-422 (Duplex) 16

AD168/MP168

AD2083-02C (AD2083-

02B ver 11YB) RS-422 (Simplex/Duplex) 60

1-180

AD2091 Manchester 64

AD2083-02B RS-422 (Duplex) 16

AD2050 AD2083-02C (AD2083-

02B ver 11YB) RS-422 (Simplex/Duplex) 60

16 1-1024

None Manchester

AD2083-02B RS-422 (Duplex) 16

AD2150

AD2083-02C (AD2083-

02B ver 11YB) RS-422 (Simplex/Duplex) 60

16 1-32

None SensorNet

RCSN422 RS-422 (Duplex) 4 16

AD32/VM32

RCSN422 (ver 1.02) RS-422 (Simplex) 0 0

1-32

None SensorNet

RCSN422 4

RS-422 (Duplex) 96

AD32E/VM32E

RCSN422 (ver 1.02) RS-422 (Simplex) 0 0

1-32

Manchester 64

SensorNet

ADMP48 (Plus) None

RS-422 (Simplex/Duplex) 96

(OFF

mode) 1-288

Altri manuali per SpeedDome Ultra VII EIS

Indice

Altri manuali American Dynamics Software

American Dynamics

American Dynamics SpeedDome Ultra II Manuale utente

American Dynamics

American Dynamics Excalibur 168 Manuale

American Dynamics

American Dynamics Intellex Policy Manager Manuale utente

American Dynamics

American Dynamics Browser Client Manuale utente

American Dynamics

American Dynamics Intellex Digital Recorder Manuale utente

American Dynamics

American Dynamics SpeedDome Ultra VII Istruzioni per l'installazione e il funzionamento

American Dynamics

American Dynamics Excalibur AD5500 Manuale utente

American Dynamics

American Dynamics Excalibur AD5500 Manuale

American Dynamics

American Dynamics Version 4.3 Software Update 3 Come usare

American Dynamics

American Dynamics SpeedDome Ultra VII Manuale utente

American Dynamics

American Dynamics Excalibur 168 Manuale utente

American Dynamics

American Dynamics MegaPower 48 Plus Manuale utente

American Dynamics

American Dynamics Intellex Policy Manager Manuale dell'operatore

American Dynamics

American Dynamics MegaPower 3200 Release 2.0 Come usare

American Dynamics

American Dynamics Video Management Systems Manuale utente

American Dynamics

American Dynamics EDVR Calculator Manuale utente

American Dynamics

American Dynamics Intellex Digital Recorder Manuale dell'operatore

American Dynamics

American Dynamics Excalibur 168 Manuale utente

American Dynamics

American Dynamics MegaPower 3200 Manuale utente

American Dynamics

American Dynamics RAS915LS Manuale utente

American Dynamics

American Dynamics CPU Activity Log Client Istruzioni operative

American Dynamics

American Dynamics Intellex Intellex LT Guida rapida

American Dynamics

American Dynamics SpeedDome Ultra III Manuale utente

American Dynamics

American Dynamics RAS915 Manuale utente

Manuali Software popolari di altre marche

COMPRO

COMPRO COMPROFM Manuale utente

Muratec

Muratec OFFICEBRIDGE ONLINE Manuale utente

Oracle

Oracle Contact Center Anywhere 8.1 Manuale utente

Adobe

Adobe 65007312 - Photoshop Lightroom Manuale

Avaya

Avaya NULL One-X for RIM Blackberry Manuale utente

HP ProLiant BL420c Manuale utente

PS Audio

PS Audio PowerPlay Manuale del proprietario

Brady

Brady LOCKOUT PRO 3.0 Manuale di servizio

Avaya

Avaya Interaction Center Manuale utente

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manuale

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manuale utente

Oracle

Oracle Application 9i Manuale utente

Acer

Acer RDM Manuale utente

Canon

Canon Vixia HF21 Manuale utente

Canon

Canon ZR950 Manuale utente

Samsung

Samsung Auto Backup Manuale utente

Polycom

Polycom Vortex EF2201 Istruzioni per l'installazione e il funzionamento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manuale utente