Amperes Quantum Series Manuale utente

PUBLIC ADDRESS POWER AMPLIFIER ● QUANTUM POWER SERIES

Thank you for choosing another quality product fromAmperes Electronics.

VER 4 / 2015

Quantum QP2000 Series of power amplifiers are the latest generation of power packs that had been developed through years

of experience, countless feedbacks and limitless fine tuning of its predecessors, thus offering a new and unique audio amplifi-

cation product.

QP2000series areavailablein thepowerrangeof 125,250,275 and500W100V lineratingswith2 huheight.Controlpartshad

been made contemporary with digital settings via front panel or through custom built software. Various and known protection

features are incorporated such as auto fault sensing (AFS), in built standbyamplifierchangeover,temperature sensing and

many more.

You shall be very certain that this is the final product you would ever search. We make it available without youpayinghigh price

for a premium product that works exceeding your expectation.

Parts Identification

45679

10 12

Front View

1. POWER SWITCH

Mains ac power switch. The unit operates with 220 - 240V ac.

2. LCD DISPLAY

2 X 18 character LCD displaying units parameters and programming instructions.

3. CONTROL BUTTONS

Buttons for various controls and setting up the unit.

4. GROUND LIFT SWITCH

Switch to isolate or link signal ground to equipment body.

PAGE 2 Quantum QP2000 Series Power Amplifiers

5. RS485 DATA LINK

RS485 data port for parameter reading or controls from PC or external triggering panel. For PC link, a USB-RS485

converter shall be required whereas the software is available free.

6. AMP. FAULT CONTACT

Adry contact shall be available if the amplifier is detected as faulty. This allows activation of external changeover or

enable external notification panel.

7. AUDIO INPUT SIGNAL

TheamplifieracceptslinebalancedaudiosignalandalinkXLRconnector isavailabletoconnect inparalleltothe next

amplifier.

8. VENTILATION FAN

It is a variable speed temperature dependant fan with air blows from inside out. The fan can be set to auto or always

on mode. See “Setting Up the Unit” in the following sections.

Rear View

PUBLIC ADDRESS POWER AMPLIFIER ● QUANTUM POWER SERIES

Quantum QP2000 Series Power Amplifiers PAGE 3

Parts Identifications ( con’t )

9. AC MAINS INPUT

Operating voltage is 220 to 240V ac ; 50 hertz. Use suitable fuse for replacement.

Recommended Fuse Replacements :

10. DC INPUT TERMINAL

24V DC back up supply from batteries are connected to these connectors. Use suitable cable size to avoid overheating

of cables.

11. AUDIO LINE OUTPUTS

Outputs fromthe unitsare available in100 /70V lineand also for4 Ohm speakers.Atany onetime, connectonly one terminal.

12. STANDBY AMPLIFIER CONNECTOR

QP2000 series are equipped with Auto Fault Sensing feature with Standby Fault Changeover relay incorporated.

Outputs from a standby unit is connected to these terminals and connected to the next duty pack in series. Please

refer to the section “ Connecting StandbyAmplifier ”.

QP2125 QP2250 QP2375 QP2500

Slow blow fuse is recommended.

5A 5A 6.3A 6.3A

PAGE 4 Quantum QP2000 Series Power Amplifiers

General Schematic Diagram

POWER

OFF SELECT

TUNER CD CASS

OFF

MASTER

MUSIC SOURCE

SIG IN

BASS

MAXMIN

EXT INPUT

MAX MAXMIN

SOURCE

MIN

SIG IN

CHIME MIXER T REBLE

MAXMIN

TONE CTRL

CH5 CH6CH4

SIG INSIGIN SIG IN

MAXMIN MAXMIN MIN

CH3CH1 CH2

SIG INSIG IN

MAXMIN MAXMIN MAXMIN MAX

AUX

SIG IN

amp e re s

M X 222 2 O

am p e r e s

POWER

QP2500

DOWN

am p e r e s

POWER

QP2500

DOWN

am p e r e s

POWER

QP2500

DOWN

am p e r e s

POWER

QP2500

DOWN

51 2 1

OVERRIDE

21 3 54 SPEAKER ZONE SELECT

6 7 8 9 10 1211

CALL

ALL

amp e re s

PM1120 PAGING MIC

MX2222 Mixer

EP1200A E/M Mic

QP2000Amplifier

Duty Unit 1

Duty Unit 2

Duty Unit 3

Standby Unit

Zone Selector

TO SPEAKERS

USB-RS485

Converter

PC with QPM

Software

INPUTS

line audio

zone

triggering

100V

line

RS485

data

Optional

Note :

Changeover :

Duty amplifier with higher priority for changeover must be placed nearest to the standby unit. ie. first output

connection from standby amplifier must be connected to this unit.

Standby fault changeover only available at 100V line outputs. Thereby to utilise this feature, speaker

connections must be terminated at 100V output terminals.

If the system consists of various ratings of power amplifiers, always allocate standby unit with the highest

power rating, to avoid overloading in the event that changeover takes place.

An example of application with

single source to amplifiers, with

one unit being a standby unit.

For Uninterrupted Paging System

or Matrix application, please

Application of PC monitoring of

amplifiers is optional.

In PC monitoring, each

power pack must be

addressed.Up toa maxof 16

nos of power packs can be

monitored.

To avoid signal distortion in

looping the audio, usage of

signal distributor (DA2208) is

strongly recommended

FIRE

PUBLIC ADDRESS POWER AMPLIFIER ● QUANTUM POWER SERIES

Quantum QP2000 Series Power Amplifiers PAGE 5

Connecting The Unit

Audio from pre-amp

mixer ( balanced line )

XLR

connections

DUTYAMPLIFIER UNIT

STANDBYAMPLIFIER

24V DC

Fr Battery

Bank 100V Line Out

To Zone Selector

100V

Out

Standby Unit

100V Line Out

Standby 100V

Line Links

note on the link

connections for

standby amplifier

Note 1 :

Loop the audio signal to a maximum of 6 to avoid signal distortion. In case that more amplifiers are required in

the system, use a signal distribution amplifier.

Note 2 :

Always ensure cable size, particularly the incoming cable from battery is sufficient enough to cater for the load

during battery takeover when the mains failed. As a rule of thumb, a 2.5mm cable shall not be linked to more

than 6 power packs.

Note 3 :

AFS only applies to 100V line output. Should you decide to turn of the feature utilising the internal changeover

relay, always connect the output at 100V line terminals.At any one time, never use different outputs simultane-

ously.

Note 4 :

The amplifier that need to be accorded top priority for changeover should be connected first to the standby

amplifier output. If the changeover occurs at the first unit, the remaining shall not be provided with back up

output.

In order for changeover to take place,AFS feature must be turned on.

Aconnection diagram for basic installation with single input source from pre-amplifier mixer.

PAGE 6 Quantum QP2000 Series Power Amplifiers

Connecting The Unit - Matrix Paging

E R 1 10 8

OUT PUT 4 O UTPUT 3 O UTP UT 2 OUTP UT 1OUT PUT 5OUT PUT 6OUT PUT 7OUT PUT 8

INPUT 4 INPUT 3 INP UT 2 INPUT 1INPUT 5INPUT 7INPUT 8 INPUT 6

PR IOR ITY

INPUT

DC 24V

0.5 A

IN-

IN+

OUT+

IN-

IN+

OUT+

OUT-

IN-

IN+

OUT+

IN -

IN +

OUT +

OUT -

OUT-

IN-

IN+

OUT+

IN-

IN+

OUT+

OUT-

IN+

IN-

CHANNEL 3CHANNEL 4

CHANNEL 5CHANNEL 6

CHANNEL 7CHANNEL 8 STANDBY

AMP

CHAN. 1

ON CHAN. 2

ON CHAN. 3

ON CHAN. 4

ON CHAN. 5

ON CHAN. 6

HIGH

CASCADE

LOW

CHANNEL 8

+ - G + -

INPUT

OUTPUT

CHANNEL 7

+ - G + -

OUTPUT INPUT

CHANNEL 6

+ - G + -

OUTPUT INPUT

CHANNEL 5

+ - G + -

OUTPUT INPUT

CHANNEL 4

+ - G + -

OUTPUT INPUT

CHANNEL 1 STANDBY

+ - G + - +- G

OUTPUT

INPUT

OUTPUT

OPENLINK

LINK

SIGNAL

OPENLINK

LINK

SIGNAL

OPENLINK

LINK

SIGNAL

OPENLINK

LINK

SIGNAL

OPENLINK

LINK

SIGNAL

CHANNEL / AMP. DETECTION SWITCHES

SWITCH TO OFF FOR UNUSED CHANNEL

FAULT

CONT.

3A NO

MAX

AUDIO SIGNAL INPUTS / OUTPUTS

RS 485

CHANNEL 3

+ - G + -

OUTPUT INPUT

OPENLINK

LINK

SIGNAL CHANNEL 2

+ - G + -

OUTPUT INPUT

OPENLINK

LINK

SIGNAL

IN-

IN+

OUT+

IN-

IN+

OUT+

OUT-

CHANNEL 1CHANNEL 2

CHAN. 7

ON CHAN. 8

AX3800

AMP.AUTO FAULT

CHANGEOVER

Note :

In matrix system, each amplifier shall be fed with different audio signal ; therebyAX3800 standby amplifier changeover unit

shall be used in the setup with the configuration shown above.

Auto fault sensing feature at QP2000 need to be turned off and fault sensing tasks shall be performed byAX3800.

If number of duty amplifiers are more than 8, add ER1108 and AX3800 accordingly.

AUDIO FROM MESSAGE

PLAYER / RECORDER

AUDIO INPUTS FROM MXP2188

MATRIX CONTROLLER

24V DC

audio to amplifier inputs

( balanced line )

100V line outputs

100V LINE OUTPUTS TO SPEAKERS

QP2000 - Standby

Duty 6

Duty 5

Duty 2

Duty 1

EP1200A

ER1108

24V

----------------

Quantum QP2000 Series Power Amplifiers PAGE 7

Connecting The Unit - Uninterrupted Paging

AUX C D

amperes

PM SERIES PAGING MIC

MX2222

MIXER

BGM Inputs

Paging audio output BGM audio output

Standby

Duty 1

Duty 2

QPAmplifiers for Paging

QPAmplifiers for BGM

Standby

Duty 1

Duty 2

ZS5602

SPEAKER ZONE SELECTOR

TO SPEAKERS

Paging Output BGM Output

Note :

In uninterrupted paging setup, two sets of amplifiers are used; Paging and BGM. Two standby unit shall be required

to serve each set of amplifiers.Auto fault feature need to be turned on at duty units.

AC 230V 50/60HZ

PAGE 8

Setting The Unit

Upon powering up the unit, the display shall

appear as shown, Initialising and into ready

mode. Displaying firmware version of

the unit Showing unit address in bracket,

volume level and temperature

To begin setting, press the MENU button. Use Next

and Prev button to shift around.

DOWN

1.0 CHANNEL SETTING

Menus available are for :

1. Channel setting

2. Cascading / setting unit address

3. Fan andAFS setting

4. Factory reset

Press MENU and menu 1

Channel setting will appear.

To select sub menu for

volume adjustment, select

1.1

PressMENU buttonand an

asterisk would appear

Use UP and DOWN key to

adjust volume level

To confirm the value, press

MENU button.

Use UP / DOWN button to

select the next sub menu

To select sub menu for

bass level, press MENU

and asterisk would appear

Use UP and DOWN key to

adjust volume level

To confirm the value, press

MENU button.

Use UP / DOWN button

to select the next sub

To select sub menu for

treble level, press MENU

and asterisk would

appear

Use UP and DOWN key

to adjust volume level

To confirm the value,

press MENU button.

Use UP / DOWN button

to return to Sub Menu 1.

Select SubMenu 1.4 and

press MENU.

Use UP and DOWN

button to select sub menu

Quantum QP2000 Series Power Amplifiers

Down

Quantum QP2000 Series Power Amplifiers PAGE 9

Setting The Unit

2. CASCADE

Select Sub Menu 2 for unit addressing

Use UP and DOWN button to select

address number

Press MENU button to confirm

Setting the address is used only when all

the amplifiers at to be linked to remote PC

for monitoring. Software is available free,

but an USB-RS485 interface shall be

required.

Among parameters that can be monitored

are volume, temperature, fan and amp

status.

Up to 32 units can be linked together for

monitoring.

3. SETTING

Select Menu 3

Use UP and DOWN button to select

Sub Menu 3.1 forAFS feature

Press MENU button to select the Sub

Menu and use UP / DOWN button to

turn On or Off.

This setting shall be forAuto Fault Sensing

(AFS) and fan control

With Auto Test feature on, Pilot Tone of

20KHzwould begenerated,andtheoutputs

shallbemonitored.Theabsence ofthetone

shall indicate the amplifier module or the

unit is faulty.

At faulty condition, a dry contact shall be

activated for external triggering. Similarly, a

fault condition data would be sent out via

RS485. Once confirm, press MENU and will

revert to Sub Menu. Use UP and

DOWN button to select other Sub

Use UP and DOWN button to select

Sub Menu 3.2 for fan control

Press MENU button to select the Sub

Menu and use UP / DOWN button to

turn On or Off.

Once confirm, press MENU and will

revert to Sub Menu. Use UP and

DOWN button to select other Sub

Fan can be set toAuto mode, which the fan

would be automatically turned on upon

reaching 29 Deg C at the heatsink and

would run at temperature dependant speed.

Another mode is to turn on the fan, running

continuously.

We recommend that the fan to be set at

Auto mode.

To exit this sub menu, select Back to

Sub Menu 3.

PAGE 10 Quantum QP2000 Series Power Amplifiers

Setting The Unit

4. INFO

Select Sub Menu 4

Output voltage from 100V line terminal

This menu provides information on

various parameters such as input and

output level.

For update Firmware to new version

Return to main menu.

5. SYSTEM Select Sub Menu 5, press MENU to enter

Firmware version

This menu provides information such as

system firmware version and would

enable the unit to reset to factory setting,

erasing all previously set data.

For resetting the unit to factory default.

6. EXIT Select Sub Menu 6, press MENU to enter

Use UP / DOWN button to toggle

between Yes and No and press MENU

button to exit.

Use this sub menu to exit setting mode.

For service purpose : the voltage prior to

step up transformer

Signal input value

Output value in dB

Altri manuali per Quantum Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Amperes Amplificatore

Amperes

Amperes PA320 Manuale utente

Amperes

Amperes AM6000 Manuale utente

Amperes

Amperes AC3801 Manuale utente

Amperes

Amperes AM4120 Manuale utente

Amperes

Amperes iPA5060 Manuale utente

Amperes

Amperes MA2060 Manuale utente

Amperes

Amperes AX700 Manuale utente

Amperes

Amperes MA2006 Manuale utente

Amperes

Amperes MC2106 Manuale utente

Amperes

Amperes AX3700 Manuale utente

Amperes

Amperes PA2120 120W 100V Manuale utente

Amperes

Amperes PA330 Manuale utente

Amperes

Amperes MX2222 Manuale utente

Amperes

Amperes PA330 Manuale utente

Amperes

Amperes DP2240 Manuale utente

Amperes

Amperes Quantum QP2125 Manuale utente

Amperes

Amperes AC3601 Manuale utente

Amperes

Amperes PA 2060 Manuale utente

Amperes

Amperes Quantum Series Manuale utente

Amperes

Amperes MX2222 Manuale utente

Amperes

Amperes MA2000 Series Manuale utente

Amperes

Amperes DP2406 Manuale utente

Amperes

Amperes MC2112 Manuale utente

Amperes

Amperes AX3800 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente