Andersen 28 STE Manuale utente
Page 1 of 17
ANDERSEN Winches
Manual for Conversion Kits
28STE Compact & 2+1 SE .............................................................2
40STE Compact & 2+1 SE .............................................................5
46STE Compact Above Deck up to version 3.2...........................7
46ST version 3.2 to 4.0 winch with drive unit..............................8
52ST/ST FS Eletric or Hydraulic Below Deck Convertion Kit ....9
52STE Compact Above Deck Version........................................10
58/62STE Compact Above Deck Version...................................13
68/72STE Compact.......................................................................15
Page 2 of 17
28STE Compact & 2+1 SE
These instructions will guide you through the
procedures to prepare your winch for use with an
ANDERSEN Compact/ 2+1SE motor. This involves
changing the bottom ratchet gear so that the winch
can be coupled to your new motor. Winches older
than November 2002 will also require a new winch
base (supplied with your motor).
Remove your winch from the boat and find a clean
and stable spot to work on your winch. As you
disassemble your winch, as described below,
carefully clean each part with degreaser. While reassembling apply a thin layer of
Andersen Winch Grease to all moving part.
Tools: Flathead screwdriver, winch-handle and ANDERSEN Winch Grease. (Newer
winches require a 4mm Alan key)
1. Loosen the screw on top of the winch and remove the drum.
2. Remove the shaft by pulling it upwards, twisting it as you go. A winch handle can be
helpful. You can then remove the top ratchet gear.
3. Remove the shaft ring and the roller bearing by sliding it up over the winch base.
You can then remove the gear wheel.
Page 3 of 17
4. Remove the circlip holding the bottom cap. The bottom cap will then fall into the
winch and you can slide the cap out through the side of the winch. The old bottom
ratchet gear can now fall out the bottom of the winch.
5. If your winch is older than November 2002 discard your old base and take the new
base supplied with your motor. For newer winches clean your old base before
reassembling.
6. With the winch base upside-down, place the new bottom ratchet gear in the bottom
of the base. Turn your winch over and place the gear wheel in position and secure it
with the roller bearing and the shaft ring.
Page 4 of 17
7. Slide the top ratchet gear into place then with a twisting motion insert the drive shaft
through the base until it falls to the bottom.
8. Your winch is now ready to be installed with your new compact/ 2+1 SE motor.
Page 5 of 17
40STE Compact & 2+1 SE
For 2003 winches on
Tools: Flathead screwdriver, hammer, punch and grease
1. Loosen the 3 screws on top of the winch and remove the drum.
2. Remove the roller bearing by sliding it up over the winch base.
3. Loosen the screw that holds the side cogwheel and remove it.
4. Place winch base in a vice or have someone hold it firmly. With a punch from a
hammer, loosen the threaded bottom cap anti clockwise, and remove it.
5. Remove the old free running cogwheel from the bottom of the winch.
Drum
Roller bearing
Side cogwheel
Winch base
Step 3 Step 4
Page 6 of 17
6. After applying grease, insert the newly supplied free running cogwheel onto the
main shaft using a twisting motion so that the pawls fall into place. Be careful! The
ratchet cogwheel can fall out before step 8 is complete.
7. Replace the side cogwheel and the roller bearing after cleaning and greasing all
moving parts. Grease the ball bearings on the top of the winch base.
8. Your winch is now ready to be installed with your new compact/2+1 SE motor.
Install the winch before replacing the drum.
Step 6
Free running cogwheel
Page 7 of 17
46STE Compact Above Deck up to version 3.2
Tools required for this conversion:
Allen keys 4mm and 5mm
Small screwdriver
Winch-handle
1. Remove the winch from its mounted position. Place the
winch drum and self-tailing arm to one side.
2. Remove the 6 or 9 screws holding the upper base to the
lower base. (Figure 1)
3. Remove the drive shaft from the upper base by pulling the
shaft upwards. To do this you can use a winch handle to pull
on the shaft. An o-ring stops the drive shaft from falling out
so some resistance should be expected when removing the
drive shaft. (Figure 2)
4. Turn the upper base upside down and remove the 2 free
gear assemblies by unscrewing the axels in the upper base.
(Figure 3)
5. Remove the complete roller bearing by sliding the ring
upwards. (Figure 4)
6. The old upper and lower bases are no longer required.
7. Reassemble the winch with the new upper and lower base
provided with your compact motor. While the winch is
disassembled it may be appropriate to carry out a general
service on the winch as described in the 46ST manual. In all
cases the gears should be cleaned and new grease applied
to all moving parts.
8. After first securing your new Compact Electric Motor to the
deck, the converted winch can now be mounted on the
motor with the screws provided.
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5, Parts to be mounted
on the new upper base
Page 8 of 17
46ST version 3.2 to 4.0 winch with drive unit
IMPORTANT INFORMATION when mounting a new winch with a drive unit.
With the 46ST version 4.0, we have integrated the deck plate features in the winch base
plate.
With the new deck plate there is a distance ring, which gives the correct height from the
unit to the winch, see the installation drawing below.
46ST up to version 3.2 46ST from version 4.0
Type with deck plate Type without deck plate
Base plate for
winch (part of
winch).
No. 746801
Distance-
ring and
O-ring.
Drive unit:
Electric or
hydraulic.
Drive unit:
Electric or
hydraulic.
Deck plate
for winch.
No.746800
Page 9 of 17
HOW TO INSTALL WINCH 52ST/ST FS WITH AN ELECTRIC OR
HYDRAULIC BELOW DECK CONVERSION KIT
52ST/ST FS version 3.0
(or later version)
52ST/ST FS version 2.5
(or earlier version)
Stainless steel
Deck plate
52ST/ST FS fromver. 3.0, has integrated
the deck plate features inthe winch base.
The lower Bronze winch base isused as
deck plate.
The distance ring, must
be used fromwinch
version 3.0 and up
Page 10 of 17
52STE/ STE FS Compact Above Deck
Conversion manual for Compact motor Above Deck.
For above deck compact motors a new lower base is
required for winches manufactured before September 2002.
This manual shows how to replace your old lower base with a
new, so that older winches will function with the new above deck
compact motor.
The numbers below in brackets ( ) refer to the position numbers
on the parts list found in the back of the 52ST owners manual.
Consult also Figure 6 to see the different parts you will be working
with. Be sure to have a clean stable work place while
disassembling your winch
1. Remove the winch drum (5) and the Self-tailing arm (2) by
removing the 4 bolts (1) on the top on the winch.
2. Remove the 6 x M8 bolts holding the winch to the deck.
3. Remove the drive
shaft (6) by sliding it
up through the upper
base (23) (Figure 1)
4. Remove the 6 bolts
(8) holding the upper
base (23) to the lower
base (26) (Figure 3)
5. Remove the upper base (23) and the bearing (25)
(Figure 2)
Figure 1
Figure 2
Figure 3
Altri manuali per 28 STE
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Andersen Verricello
Andersen
Andersen 28 STE Manuale utente
Andersen
Andersen 28 Manuale utente
Andersen
Andersen 58/62 STE SE Manuale utente
Andersen
Andersen 28ST Manuale utente
Andersen
Andersen 52ST Manuale utente
Andersen
Andersen 18ST FS Manuale utente
Andersen
Andersen WINCH 40 Guida utente
Andersen
Andersen 82-3ST Manuale utente
Andersen
Andersen 12ST Manuale utente
Andersen
Andersen 34ST Manuale utente
Andersen
Andersen Compact Motor 68/72ST Manuale utente
Andersen
Andersen 52ST Manuale utente
Andersen
Andersen RA2046001300 Manuale utente
Andersen
Andersen 46ST Manuale utente
Andersen
Andersen Compact Motor 58-62ST Manuale utente
Andersen
Andersen 46ST Manuale utente
Andersen
Andersen 52ST Manuale utente
Andersen
Andersen 40ST FS Manuale utente
Andersen
Andersen 18ST Manuale utente
Andersen
Andersen E1 Manuale utente
