AnyTone 578 Go Box DIY Kit Manuale utente
Website: www.goboxradio.com
Contact: goboxrad[email protected]
1
______________________________________________________________________________
AnyTone 578 Go Box - DIY Kit
Thank you for purchasing a Go Box Radio.
The following parts will be needed to complete your AnyTone 578 Go
Box – DIY Kit:
Website: www.goboxradio.com
Contact: goboxrad[email protected]
2
Required Parts:
•Quanty 2 - 6ah LifePo4 baeries - Both the Feuruetc or Miady
baeries work well. Order whichever is available and cheaper at
the me.
Feuruetc baeries:
hps://www.amazon.com/gp/product/B0BHMVL4N8
Miady baeries:
hps://www.amazon.com/gp/product/B07Q7FY8CC
•Baery capacity voltage monitor
hps://powerwerx.com/baery-capacity-meter-gauge-lithium
•Blue Sea Systems water resistant black Contoura III switch
hps://www.amazon.com/dp/B000Y87W54?ref_=cm_sw_r_apin_
dp_8T7M5PG123FYNJG5MHTC
•Carbon composite Anderson Powerpole panel mount
hps://www.ebay.com/itm/255243451694
•BNC male right angle to UHF male PL259 90° pigtail jumper 20”
hps://www.ebay.com/itm/195351342055
•SMA female bulkhead mount to SMA male right angle RG316
hps://www.amazon.com/gp/product/B08139CQLG
•IP68 waterproof BNC adapter, F/F with dust cap
hps://www.pasternack.com/waterproof-75-ohm-bnc-female-to-
Website: www.goboxradio.com
Contact: goboxrad[email protected]
3
75-ohm-bnc-female-bulkhead-mount-adapter-ip68-in-series-
pead1266-p.aspx
•Plasc 0.50 caliber ammo box
hps://www.harborfreight.com/050-caliber-ammo-box-
57766.html
•Turn buon fasteners
hps://www.ebay.com/itm/324731250698
•T-Type 2 pin power connector
hps://www.amazon.com/gp/product/B08HYC49NS
Required generic parts – The following parts are generic and you may
already have some or all of them. The spade connectors listed below
are specically fully insulated, but not heat-shrink style. We don’t
recommend the heat-shrink style because they tend to be longer and
don’t allow enough clearance between the back of the power switch
and the le baery.
•4 port lever wire conductor (you will need two connectors (25
come in this pack)
hps://www.amazon.com/dp/B087PBHG9L
•6 port lever wire conductor (you will need one connector. 10
come in this pack)
hps://www.amazon.com/dp/B0B28H4SX6
•14 gauge wire (you will need approximately 6 feet of wire. 20
come on this spool)
hps://www.amazon.com/dp/B0779RCGGW
Website: www.goboxradio.com
Contact: goboxrad[email protected]
4
•Female spade connectors (you will need 7. 100 come in this
pack)
hps://www.amazon.com/gp/product/B06XCWHY1B
Assembly
Step 1 – Prepare your wires and connectors.
•Cut 6 12” lengths of black/red pair wire from your spool.
•Separate one black/red pair into a single red wire and discard the
black wire.
•Strip one end of all wires.
•Crimp spade connectors onto 3 of black/red pair secons.
Website: www.goboxradio.com
Contact: goboxrad[email protected]
5
•Crimp a spade connector onto the single red wire.
You should now have:
•3 black/red wire pairs with spade connectors on one end.
•1 red wire with a spade connector on one end.
•2 black/red pairs that are stripped on one end
Step 2 – Assemble Carbon Composite Anderson Powerpole Panel
Mount
•Crimp Powerpole contacts onto one stripped black/red wire pairs
made in previous step.
•Insert Powerpole contacts into corresponding Powerpole red and
black connectors.
oTip: It’s helpful to use a small athead screwdriver to push
on the back of the contact to seat it in the connectors. Push
unl you hear or feel it click into place.
•Connect Powerpole connectors to each other by sliding one side
dovetail into the dovetail of the other.
oTip: The red connector should be on the right as pictured
below.
•Insert the Powerpole connector pair into the carbon composite
body, with red connector on the right (as pictured below).
•Insert and insert allen screw into the carbon composite body to
lock connectors in place.
Website: www.goboxradio.com
Contact: goboxrad[email protected]
6
Step 3 – Prepare Baery Monitor Leads
•Remove Powerwerx baery monitor from package and locate the
wire leads.
•Cut a 1.5” length of wire o your spool.
•Separate the black/red pair into individual wires.
•Strip one side of each wire.
•Solder short secon of wire to the baery monitor leads, as
pictured below.
Website: www.goboxradio.com
Contact: goboxrad[email protected]
7
Step 4 – Build T-Type 2 Pin Power Connector
•Crip T-Type 2 Pin Power Connector spade connectors to stripped
black/red wire pair.
•Insert spade connectors into T-Type Connector
Step 5 – Cut BNC Passthrough Hole in Ammo Can
Your AnyTone 578 Go Box – DIY Kit comes with two sperate templates
for locang the BNC passthrough hole. One is for use with a hole saw.
The other is for using a rotary tool to cut out the hole. The second
method is preferred, as cung the hole to the exact shape of the BNC
Website: www.goboxradio.com
Contact: goboxrad[email protected]
8
passthrough will prevent the BNC passthrough from rotang. With that
said, either method is acceptable.
The BNC passthrough hole should be located at the top right of the
ammo can. As you look at the radio, the lid should open to the le. The
idea behind locang the passthrough here is that you can run the
ammo can on its side, with the antenna or antenna cable aached, as
pictured below.
•Place the ammo can on a at surface.
•Place template in upper HDPE inner frame, as pictured below.
Website: www.goboxradio.com
Contact: goboxrad[email protected]
9
•Place upper HDPE inner frame on at surface on the outside of
the ammo can, as pictured below.
oTip: Try to center the upper HDPE inner frame to the ammo
can as much as possible.
Website: www.goboxradio.com
Contact: goboxrad[email protected]
10
•Mark the ammo can using a permanent marker.
Altri manuali AnyTone Radio
AnyTone
AnyTone AM-580 Manuale utente
AnyTone
AnyTone METIS Manuale utente
AnyTone
AnyTone AT-779UV Manuale utente
AnyTone
AnyTone Dual Band FM Transceiver Manuale utente
AnyTone
AnyTone AT-D578UV Manuale utente
AnyTone
AnyTone AT-588UV Manuale utente
AnyTone
AnyTone ARES II Manuale utente
AnyTone
AnyTone AT-D868UV Istruzioni operative
AnyTone
AnyTone AT888 Manuale utente
AnyTone
AnyTone AT-318UV Manuale utente
AnyTone
AnyTone AT- 778UV Manuale utente
AnyTone
AnyTone AT-D578UV Guida all'installazione
AnyTone
AnyTone AT-310M Manuale utente
AnyTone
AnyTone AT-598 Manuale utente
AnyTone
AnyTone DMR AT-D878U Manuale utente
AnyTone
AnyTone SMART Manuale utente
AnyTone
AnyTone Apollo II Manuale utente
AnyTone
AnyTone ARES II Manuale utente
AnyTone
AnyTone AT-3318UV Manuale utente
AnyTone
AnyTone AT-5555 PLUS Manuale utente
