APlusLift HW-8S Manuale utente
1
INSTALLATION & OPERATION
MANUAL
APlusLift HW-8S, HW-8SXLT 4-Post Portable
Storage Car Lift
8,000LB Capacity
3
Specification and Features
•Dimensions:HW-8S (HW-8SXLT)
◦Overall Length: 175" (190”)
◦Overall Height: 84" (94”)
◦Overall Width: 106" (112”)
◦Lifting Height: 72" (82”)
◦Clearance Under Runway: 69" (79”)
◦Width between Posts: 99" (105”)
◦Drive Through Width: 93" (99”)
◦Runway Size: 165"L x 18 1/2"W (180"L x 18 1/2"W)
◦Distance between Runways: 38" Inside-Inside, 75" Outside-Outside
◦Column Cross Section: 6"L x 4"W
◦Approach Ramps Size: 32"L x 18 1/2"W
•Shipping and Installation
◦Minimum Concrete Thickness: 4"
◦Shipping Weight: 1,750lbs (1850lbs)
◦Shipping package size: 166"L x 22"W x 30"H (186"L x 22"W x 30"H)
•Safety and Specs
◦Lifting Capacity: 8,000lbs
◦Runway Gauge Steel: 6
◦Lock Positions: 10
◦Usage: Parking/Storage/Service
◦Lifting Time: 40 seconds
◦Powder Coated Finish with Superior Corrosion Resistance
◦Caster Kit, Tool Tray, 3 Drip Trays, and 2 Approach Ramps Included
•Service
◦Motor: 110V Single Phase 1.5HP 10A (recommend a 30A breaker)
◦Hydraulic Oil: 3-5 gallons AW32/AW46
4
Important Information
READ THIS BEFORE INSTALLING THE LIFT! Improper installation can cause injury or
damage!
•Read this installation and operation manual in its entirety before attempting to install
the lift. Manufacturer or distributor assumes no responsibility for loss or damage of any
kind, expressed or implied, resulting from improper installation or use of this lift. Always
use professional installation companies.
•All persons using the equipment must be responsible, qualified, and carefully follow the
operation and safety guidelines contained in this manual.
•Alevel floor is required for proper lift installation and operation.
•DO NOT install this lift on any asphalt surface. Recommend on concrete surface a
minimum of 4” thick and 3,500 psi tensile strength with steel or fiber mesh
reinforcement.
•DO NOT install this lift over concrete expansion joints or cracks. (Check with your
building architect)
•DO NOT install this lift on an upper floor without written authorization from your
building architect. Should only be installed on a ground floor without a basement.
•DO NOT attempt to lift only part of a vehicle. This lift is intended to raise the entire
body of a vehicle only.
•NEVER lift any persons or vehicles containing persons. This lift is designed to lift
empty vehicles only.
Recommended tools
•Rubber hammer
•Chalk line
•Sockets and open wrench set
•Ratchet driver
•Vise grips
•Tape measure
•Screwdrivers
•Torque wrench
•Two 10' to 12' step ladders
•4' level
•12" crescent wrench
•AW32 non-foaming hydraulic fluid (3-5 gallons)
5
Installation Requirements
•Use proper lifting techniques when lifting individual pieces. Use plenty of help when
moving lift pieces. Please wear work gloves to protect your hands.
•The lift should be installed on a leveled floor with a slope of less than 3 degrees.
•Do not install this lift on asphalt, wood, or any other surface other than described.
•Do not install this lift outdoors, the lift was designed for indoor use and is not built to be
exposed to the outdoor elements.
•Do not install lift in a basement or on any level other than ground level (such as the
second floor) without written authorization from your building engineer or architect.
•Maintain a 6" minimum distance from a slab edge. Do not install this lift over expansion
joints or cracks. Check with your qualified engineer or architect.
•Leave spaces on all 4 sides when placing the lift. Recommended at least 2’ distances
on all 4 sides when a vehicle is loaded.
•Improper installation can cause damage or injury. Manufacturer will assume no liability
for loss or damage of any kind, expressed or implied, resulting from improper
installation or use of this product.
•The lift is for lifting vehicles only. It is not designed to lift a person or an equipment with
a person.
•Read this installation manual in its entirely before attempting to install this lift.
•Use of this lift should follow the operation and safety guidelines set forth in this manual.
6
Installation Instructions
Step 1 (Preparation)
•Please carefully remove all the parts from the package.
◦Remove any loose cables, hoses, part boxes, hydraulic power unit, etc. if they are
inside the columns or banded to the columns.
◦Remove the power unit box.
•Compare the parts with the part list (at the end of the manual) and contact APlusLift if
there are any parts missing.
•Please read the installation requirements in previous pages for concrete requirement
and layout. The area where the lift will be installed should be free of overhead
obstructions such as heater, building support, or electrical lines.
7
Step 2 (Setting up Columns and Rails)
•Lay out the columns (x4), tracks (x2), and cross rails (x2).
•Place the cross rails into the column, aligning the locks and the steps on the same
side.
•Slide the cross rail to the lowest position. Release the lock rod to do so. Repeat these
steps for each of the other columns.
•Place the runway across the cross rails, the lip should be resting on the cross rails,
smooth part facing outwards.
•Install the runway hardware (large bolts (x8), flat washers, lock washers, nuts, and
ramp hangers)
8
Step 3 (Installing Cables)
•The cables come pre-installed in the runway along with the cylinder. Route the cables
in a manner in such that the two rear cables are in the front of the terminal block and
the front two corners are in the back of the terminal.
•Install the cables by running the ram manually by pulling it out on the ram by hand. Do
not add hydraulic fluid yet as the ram will not be able to be operated manually once
hydraulic fluid is added.
•Run cables through the pulleys on the cross rail and up towards the top of the columns
where there is a termination point.
•Attach the front lock release.
•Connect the release T rod with the long rod under runway.
9
10
Step 5 (Installing Power Unit)
•Hang the power unit mounting bracket.
•Install the hydraulic hose from the cylinder through the appropriate spot located on the
runway.
•Connect the hydraulic hose to the power unit.
•Connect straight end into the runway fitting.
•Make sure all fittings are secure.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali APlusLift Sistema di sollevamento
APlusLift
APlusLift HW-10KBP Manuale utente
APlusLift
APlusLift AP-10SR Manuale utente
APlusLift
APlusLift HW-12S Guida rapida
APlusLift
APlusLift HW-9KOH Manuale utente
APlusLift
APlusLift HW-10KOH Manuale utente
APlusLift
APlusLift SL-MR80 Guida
APlusLift
APlusLift HW-9KBP Manuale utente
APlusLift
APlusLift MT1500 Manuale utente
APlusLift
APlusLift HW-10KBP Manuale utente
APlusLift
APlusLift MT1500 Manuale utente
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
