Apricorn Aegis Bio 3.0 Manuale utente

Quick Start Guide

Basic LED States

LOCK RED LED

UNLOCK GREEN LED

ADMIN BLUE LED

4ENROLL Button

Solid RED = Standby, swipe nger to unlock

Flashing RED = Error

Solid BLUE / Flashing GREEN = Ready to enroll ngerprint

Solid GREEN = Drive unlocked

Flashing GREEN = Disk activity

Aegis Bio 3.0

Swiping your Finger

To successfully swipe your nger,

start your swipe by placing your

ngertip on the downward facing

arrow at the top of the biometric

sensor. Swipe your nger in a

downward motion across the

sensor. If your swipe is successful

the GREEN LED will start to icker.

Start

swipe

here

1. Attach the integrated USB cable of

the Aegis Bio to an available USB

port on your computer. The Aegis

Bio LEDs will show Solid BLUE and

Flashing GREEN indicating that the

drive is ready to enroll your ngerprint.

2. Swipe your Finger. The BLUE LED

will turn off while the GREEN LED

starts to icker briey as the Aegis Bio

processes your ngerprint.

Wait until the BLUE LED turns back

to Solid BLUE and the GREEN LED

returns to its ashing state.

3. Continue to repeat Step 2 until both

the BLUE and GREEN LED are

in a solid state, indicating that your

ngerprint is fully enrolled.

NOTE: The number of attempts will vary depending on the quality of

the ngerprint read. For most people six swipes will be sufcient.

If there is a problem with a ngerprint read, the BLUE LED will turn off and

the RED LED with start to ash.

4. To enroll more ngerprints, press the ENROLL button within 15

seconds from your last successful ngerprint enrollment and repeat

the process in steps 2 and 3.

NOTE: A maximum of 5 ngerprints can be stored. There is a 15 second

timeout between entering ngerprints. If the ENROLL button is not pressed

again after the last ngerprint, the unit will assume no more ngerprints will

be entered and return to a standby state.

Once 5 ngerprints have been stored, all three LEDs will turn on. After 2

seconds the GREEN and BLUE LED will turn off with just the Solid RED

LED showing. At this point no more ngerprints can be enrolled.

NOTE: Once enrolled, ngerprints cannot be un-enrolled

individually. To remove enrolled ngerprints, a complete re-set

of the drive is required.

Getting Started - Out of the Box

TIP: We highly recommend that you enroll at least three

different ngers to ensure access to the drive in the case

that your primary nger cannot be used.

Unlocking the Aegis Bio

Locking the Aegis Bio

Complete Reset

To lock the Aegis Bio after it has been unlocked, use the directions below.

1. Press the ENROLL button until the RED LED turns on. The drive

will check for disk activity. If no data has been written to the drive for 2

seconds, the drive will lock. If data is being written to the drive, it will wait

until the disk activity has been nished before locking the drive.

2. The Aegis Bio LED will go from GREEN to Solid RED when locked.

NOTE: If you use the safely remove hardware button (Windows) or

Eject device (Mac), the Aegis Bio will lock and dismount but the LED

will remain GREEN. You will need to physically remove and re-plug the

USB cable before being able to access the drive.

Once your ngerprints are enrolled, unlock the Aegis Bio using the directions below.

1. Attach the integrated USB cable of the Aegis Bio to an available USB port

on your computer. The Aegis Bio LED will show Solid RED indicating that

the drive is locked and is in Standby mode.

2. Swipe your Finger. The RED LED will turn off while the GREEN LED will start

to icker briey as the Aegis Bio processes your ngerprint.

3. You will know that your ngerprint has been accepted once the GREEN

LED stops ickering and turns Solid GREEN. The drive is now unlocked

and ready for use.

NOTE: The complete re-set will delete all stored ngerprints and will

change the encryption key used to secure the drive.

THIS WILL ERASE ANY DATA ON THE DRIVE. USE WITH CAUTION.

1. Hold down the ENROLL button and plug the Aegis Bio USB cable into

your computer. The LED will alternate RED / BLUE.

2. Release the ENROLL button, then within 5 seconds repress and hold the

ENROLL button for 15 seconds. The LED will alternate between RED /

BLUE / GREEN during the 15 seconds.

3. When the drive successfully resets, the GREEN LED will stay on for 3

seconds, then will change to Solid BLUE with the GREEN LED ashing.

You can now release the ENROLL button.

4. The Aegis Bio has now been returned to its OUT OF THE BOX state

and is now ready to enroll ngerprints. Once ngerprints are enrolled

the Aegis Bio will need to be partitioned and reformatted before use.

(For formatting and partition instructions refer to product manual.)

Enrolling a new nger

If there are less than 5 ngerprints enrolled and you want to enroll a new nger,

follow the instructions below.

1. Plug in the Aegis Bio to a USB port on your computer. The LED should

be Solid RED indicating that the drive is Standby mode.

2. Push the ENROLL button for 3 seconds.

If less than 5 ngerprints are enrolled, the BLUE LED will become Solid

BLUE and RED LED will remain illuminated. Proceed to Step 3.

If 5 ngerprints are enrolled, the BLUE and GREEN LED will come on for 2

seconds and the RED LED will be Solid RED. You will not be able to enroll

any more ngerprints.

3. Swipe a nger that has been previously enrolled. The GREEN LED will

ash if the ngerprint is accepted. If the ngerprint is not accepted the RED

LED will ash.

4. Once the ngerprint is accepted the BLUE LED will become Solid BLUE and

the GREEN LED will continue ashing, indicating that the Aegis Bio is ready

to enroll a new ngerprint.

5. Swipe a new nger. The BLUE LED will turn off while the GREEN LED

starts to icker briey as the Aegis Bio processes your new ngerprint.

Wait until the BLUE LED turns back to Solid BLUE and the GREEN LED

returns to its ashing state.

6. Repeat Step 5 until both the BLUE and GREEN LED are in a solid state,

indicating that your ngerprint is fully enrolled.

NOTE: Once enrolled, ngerprints cannot be un-enrolled individually. To

remove enrolled ngerprints, a complete re-set of the drive is required.

Apricorn provides the following helpful resources for you:

1. Apricorn’s Website (http://www.apricorn.com)

This gives you the ability to check for up-to-date information

2. E-mail us at [email protected]

3. Or call the Technical Support Department at 1-800-458-5448

Apricorn’s Technical Support Specialists are available from 8:00 a.m. to

5:00 p.m., Pacic Standard Time Monday through Friday

Technical Support

Altri manuali per Aegis Bio 3.0

Indice

Altri manuali Apricorn Magazzinaggio

Apricorn

Apricorn Aegis Bio A25-BIO 640GB Manuale utente

Apricorn

Apricorn Aegis Padlock DT Manuale utente

Apricorn

Apricorn Aegis Padlock A25-PL256 128GB Manuale utente

Apricorn

Apricorn Aegis Padlock Fortress Manuale utente

Apricorn

Apricorn Aegis Bio 3.0 Manuale utente

Apricorn

Apricorn Aegis Padlock Manuale utente

Apricorn

Apricorn USB Storage Device Manuale utente

Apricorn

Apricorn Aegis Secure Key Manuale utente

Apricorn

Apricorn Aegis Padlock DT Manuale utente

Apricorn

Apricorn Aegis Mini A18-USB 240GB Manuale utente

Apricorn

Apricorn Aegis Padlock A25-PL128 640GB Manuale utente

Apricorn

Apricorn Xtreme Upgrade Manuale utente

Apricorn

Apricorn EZ-BUS-DTC 250GB Manuale utente

Apricorn

Apricorn ADVRX 500GB Manuale utente

Apricorn

Apricorn Aegis Padlock A25-PLE256 500GB Manuale utente

Apricorn

Apricorn Aegis Fortress Manuale utente

Apricorn

Apricorn Aegis Bio A25-BIO 120GB Manuale utente

Apricorn

Apricorn Aegis Portable A25-FW 120GB Manuale utente

Apricorn

Apricorn Aegis Portable A25-USB 160GB Manuale utente

Apricorn

Apricorn Xtreme Upgrade Manuale utente

Apricorn

Apricorn Aegis Portable Manuale utente

Apricorn

Apricorn Velocity Solo x2 Manuale utente

Apricorn

Apricorn Aegis Padlock A25-PLE256S 128GB Manuale utente

Apricorn

Apricorn Aegis Secure Key 3z Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente