APsystems YC1000-3 Series Manuale utente

Questo manuale è adatto per i seguenti modelli

1

Indice

Altri manuali APsystems Invertitore

APsystems

APsystems EZ1 Series Manuale utente

APsystems

APsystems QT2 Manuale utente

APsystems

APsystems QS1-LK Manuale utente

APsystems

APsystems DS3 Series Manuale utente

APsystems

APsystems QT2 Manuale utente

APsystems

APsystems QS1 Manuale utente

APsystems

APsystems QT2 Manuale utente

APsystems

APsystems QS1-EU Manuale utente

APsystems

APsystems DS3D Manuale utente

APsystems

APsystems DS3 Series Manuale utente

APsystems

APsystems QT2-208 Manuale utente

APsystems

APsystems YC600B Manuale utente

APsystems

APsystems YC500i Series Manuale di istruzioni

APsystems

APsystems QS1 Manuale utente

APsystems

APsystems YC1000-3 3-Phase Manuale di istruzioni

APsystems

APsystems EZ1 Series Manuale utente

APsystems

APsystems YC600 Manuale utente

APsystems

APsystems QT2-220 Manuale utente

APsystems

APsystems QT2D Manuale utente

APsystems

APsystems YC600 Manuale utente

APsystems

APsystems YC500A Manuale di istruzioni

APsystems

APsystems QT2-EU Manuale utente

APsystems

APsystems QT2 Manuale utente

APsystems

APsystems QS1 Manuale utente

Manuali Invertitore popolari di altre marche

Fourgroup

Fourgroup Easy Manuale utente

Velleman

Velleman PI300M Manuale utente

Sungrow

Sungrow SG350HX-US Manuale utente

WilTec

WilTec 61897 Manuale utente

SMA

SMA SUNNY BOY STORAGE 2.5 Manuale utente

Simplicity

Simplicity LANDLORD 316 Manuale utente

Santak

Santak SMAX 3000 Manuale utente

ATON

ATON RA.Store-3 Manuale utente

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuale utente

Tektronix

Tektronix CFG250 Manuale utente

Champion

Champion 200989 Manuale utente

Vanner

Vanner 20-500 Series Manuale utente

GE

GE GEP Manuale utente

Astrel Group

Astrel Group Power Reducer Guida rapida

MULTIQUIP

MULTIQUIP GDP-5H Guida

GoWISE

GoWISE PS1007 Manuale utente

Promate

Promate PM13500D ES Manuale utente

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuale utente

REV1.2 Quick Installation Guide

1

APsystems YC1000-3-EU Microinverter Quick Installation Guide

The sketch of YC1000-3 support system.

All the solar panels are placed into two lines. Then put a YC1000-3 in the middle of the two lines and make

sure it is easy to connect with to four panels which are next to it, as well all the cables.

Step 1. Verify the grid voltage to match with microinverter rating.

Step 2. Lay the AC bus according to the arrangement of APsystems Microinverter.

Step 3. Attach the APsystems Microinverters to the racking.

Step 4. Attach the antenna to the microinverter, and keep the antenna vertical to the

earth.

Step 5. Connect the APsystems Microinverter cables to the AC bus cable.

NOTE: AC connector interface as follows, NOTE: Cover all unused T connectors with

from left to right PE, N, L3, L2, L1. sealing caps to protect the T connectors.

REV1.2 Quick Installation Guide

2

Step 6. Place the PV modules and connect each YC1000 to four PV modules close-by.

CH4 CH3 CH2 CH1

Step 7. Install a protective end cap at the end of AC bus cable.

a．Wire stripping

b．Insert the cable end into the gasket clamp.

c．Insert five wires into five cable clamps.

d．Rotate the nut with 2.5N·m until the latching

mechanism meets the base.

Step 8. Install the AC branch circuit junction box.

Step 9. Connect the cables to the branch junction box.

a. Put the unused end of the AC interconnector cable into the branch junction box.

b. Place cable connecting to the point of load interconnection into the branch junction box.

c. Wire the conductors: BROWN-L1; BLACK -L2; GRAY-L3; LIGHT BLUE-N; YELLOW GREEN-PE.

Step 10. Complete the APsystems installation map.

Each APsystems microinverter has two removable serial number labels. Peel labels off, affix one to the

respective location on the APsystems installation map, and affix another to the PV module frame which is

easy to see. Use the Scanning Gun to scan the serial numbers on the map into the computer or scan by

mobile phone, then complete the setting (see ECU manual).

NOTE: Step 1~10 can change sequence for convenience of installation.

Step 11. Start the operation.

1. Turn on the AC circuit breaker on each microinverter AC branch circuit.

2. Turn on the main utility-grid AC circuit breaker. Your system will start producing power after a

five-minute waiting time.

Product information is subject to change without notice.

(Please download manuals at www.APsystems.com).

Nut

Gaske Clamp

Body