Aqualisa Quartz QZ.B3.WR.05 Manuale utente
Quartz Digital Wirele remote installation instructions Page 4
Important information
Quartz Digital Wireless remote controls provide a secondary method of Start/Stop to the Quartz Digital product
controllers.
Quartz Digital Wireless remote controls can operate from up to 10m away from the receiver box plugged into the main
processor unit.
THIS PRODUCT UST BE INSTALLED BY A CO PETENT PERSON IN ACCORDANCE WITH ALL RELEVANT CURRENT
WATER AND ELECTRICAL SUPPLY REGULATIONS.
This product is suitable for domestic use only.
This product is supplied complete with a 2 year guarantee. The battery is not covered by the terms of this guarantee.
A replacement CR2450 battery is available from Aqualisa Customer Service, part no: 910197. Any product problems
that may arise should the incorrect replacement battery be used, will not be covered by the terms of our guarantee.
Quartz Digital Wirele remote installation instructions Page 5
Installation instructions
Using the back plate as a
template, mark out the position
of the fixing screws.
1
Wirele remote
In addition to the guide below it is essential that the written
instructions below are read and understood and that you have all
the necessary components (shown overleaf) before commencing
installation. Failure to install the product in accordance with these
instructions may adversely affect the warranty terms and
conditions. Do not undertake any part of this installation unless you
are competent to do so. Prior to starting ensure that you are famil-
iar with the necessary plumbing regulations required to install the
product correctly and safely.
THE DIGITAL PROCESSOR UST BE DISCONNECTED FRO THE
AINS POWER SUPPLY PRIOR TO INSTALLING THE RISE DIGITAL
WIRELESS RE OTE.
Drill and prepare the fixing points
using the fixings supplied, if suitable.
Fit the wall plate onto the back plate
taking care to line up the location
slots on the back plate, then fit the
assembly onto the wall.
2
!
Quartz Digital Wirele remote installation instructions Page 6
Using a large flat bladed
screwdriver, carefully undo the
battery cover by turning it a
quarter turn.
3
Place the CR2450 battery,
positive side facing up, into
the rear of the Wireless remote
control. (The positive side of the
battery is the widest side, with
the imprinted written details).
4
Replace the battery cover turning
it a quarter turn to lock in place.
5
Locate the button assembly onto
the back plate assembly with
the Start/Stop graphic in the
horizontal position. Insert the
top edge first then carefully click
the bottom into position.
6
If required, to release the button,
insert a small flat bladed screw
driver into the small opening at the
6 o’clock position, to release the
locking mechanism and pull the
bottom of the button forwards.
!
Quartz Digital Wirele remote installation instructions Page 7
BEFORE ANY ELECTRICAL ADJUST ENT IS ATTE PTED, THE
ELECTRICITY SUPPLY UST BE TURNED OFF AT THE AINS SWITCH.
ELECTRICAL INSTALLATION AY ONLY BE CARRIED OUT BY
A QUALIFIED PERSON.
!
The Digital processor features a sec-
ondary data cable socket next to
the main data cable connection.
Carefully snap and remove the
entry pillar and insert the patch
lead data cable into the socket as
shown.
7
Insert the other end of the patch
lead data cable into the receiver
box.
8
Prior to commissioning the Quartz Digital Wireless remote
following the procedure below, please refer to the installation in-
structions provided with the main Quartz Digital product to
complete the installation of the Digital processor.
10
Secure the receiver box to a flat
horizontal surface using suitable fix-
ings.
9
!If required, the top of the receiver
box can be removed by first
removing the fixing screws securing
the receiver box to the flat surface.
Disengage the two fixing lugs at one end of the box and carefully
lift the top clear.
Quartz Digital Wirele remote installation instructions Page 8
Changing the battery
!A replacement CR2450 battery is available from
Aqualisa Customer Service on 01959 560010, part
no: 910197. Any product problems that may arise
if any other replacement battery is used, will not be
covered by our terms of guarantee.
The exhausted battery should not be disposed of
in municipal waste. Use a battery disposal facility.
Please check local waste regulations.
To release the button, insert
a small flat bladed screw
driver into the small
opening at the 6 o’clock
position to release the
locking mechanism and pull
the bottom of the button
forwards.
1
Using a large flat bladed
screwdriver, carefully undo
the battery cover by
turning it a quarter turn.
2
Place the CR2450 battery,
positive side facing up, into
the rear of the Wireless
remote control.
(The positive side of the
battery is the widest side,
with the imprinted written
details).
3
Quartz Digital Wirele remote installation instructions Page 9
Replace the battery cover
turning it a quarter turn to
lock in place.
4
Locate the button assembly
onto the back plate
assembly with the
Start/Stop graphic in the
horizontal position. Insert
the top edge first then
carefully click the bottom
into position.
5
Aqualisa Products Limited
The Flyer’s Way
Westerham Kent TN16 1DE
Customer helpline: 01959 560010
Brochure Hotline: 0800 652 3669
Website: www.aqualisa.co.uk
Email: [email protected]
Republic of Ireland
Sales enquiries: 01-864-3363
Service enquiries: 01-844-3212
Part No:700200 Issue 01 Dec 12
Please note that calls may be recorded for training and quality purposes
The company reserves the right to alter, change or modify the product specifications without prior warning
® Registered Trademark Aqualisa Products Limited
Indice
Altri manuali Aqualisa Telecomando
Aqualisa
Aqualisa ilux Manuale utente
Aqualisa
Aqualisa Visage Manuale utente
Aqualisa
Aqualisa AQLS Manuale utente
Aqualisa
Aqualisa QUARTZ DIGITAL SERIES Manuale utente
Aqualisa
Aqualisa Quartz Digital QZD.B3.DS.14 Manuale utente
Aqualisa
Aqualisa Optic Q WR.BL.CP.20 Guida
Aqualisa
Aqualisa iSys ISD.B3.DS.14 Manuale utente
