ARC MEBT-1706 Manuale utente

Indice

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione

1

Issue date: 21/01/2020

MINI EASY ONE BUTTON

REMOTE CONTROL

MEBT-1706

CONTENTS

1. Overview and features Page 2.

2. Diagrams Page 3.

3. Battery Page 4.

4. Mounting on surface Page 4.

5. Pairing / Un-pairing device Page 8.

6. Scene setup / Scene control Page 9.

7. Operation Page 17.

8. Specifications Page 19.

2

Issue date: 21/01/2020

1.Overview and features

Easy one button remote control with 3 LED colour indication. (Red / Green /

Amber).

Equipped with 3 scene control and 1 ALL OFF control.

New dimming method by holding down the button to take control of the load

level.

3V CR2450 battery operation capable of 3 year battery life and built in battery

low indicator.

Main features of remote control;

•Compatible to L and M series.

•Easy freestanding on the table, mounting with screws or use adhesive

tape on flat surface.

•Simple single and double click action.

•Scene status memory, create your desired atmosphere.

•Actions are confirmed by the built-in LED indication.

OVERVIEW AND FEATURES

3

Issue date: 21/01/2020

2.Diagrams.

Notes for the diagrams:

DIAGRAMS

Function Switch

1. Load Control

2. Scene Control

3. Scene Setup

4

Issue date: 21/01/2020

3.Battery

Red LED will flash once every 4 seconds to indicate the battery is low.

1. With the one button remote control bottom facing up gently slide down the

back cabinet.

2. Remove battery insulation strip. (First time use only)

BATTERY

5

Issue date: 21/01/2020

3. Or replacing a new battery use a slot screwdriver and push down the small

metal spring then push out the battery.

4. Replace with a new 3V CR2450 battery making the positive symbol is facing

upwards.

BATTERY

6

Issue date: 21/01/2020

5. Slide battery compartment upwards to complete the battery replacement.

LITHIUM BATTERY CAUTION:

Risk of Explosion if battery is replaced by an incorrect type. Dispose of used

batteries according to the environment protection rules.

BATTERY

7

Issue date: 21/01/2020

4.Mounting On Surface

Easy one button remote control has 2 ways of mounting on flat surface.

1. With 3M double sided adhesive tape enclosed in the accessory pack.

2. Mounting with 2 screws enclosed in the accessory pack:

•Place the back battery cabinet onto wall surface making sure ‘UP’ symbol is

facing upward and arrow facing downwards.

•With cross head screw driver, tighten the back cabinet onto surface.

•With the push button facing towards you make sure the ‘UP’ symbol is facing

upwards, then align the triangle to the bottom rim onto the red line and gently

slide down the push button.

MOUNTING ON SURFACE

8

Issue date: 21/01/2020

5.Pairing / Un-pairing Device

PAIRING /UN-PAIRING

Refer to the relevant receiver operation manual that you wish to control for

detailed pairing / un-pairing procedure.

With the receiver that you intent to use, enter into “Learning Mode”

Function switch at position 1.

To Pair:

Press button once. Green LED flash once.

To Un-Pair:

Press button twice. Red LED flash twice.

PAIRING / UN-PARING DEVICE

LED Flash once

LED Flash twice

9

Issue date: 21/01/2020

6.Scene Setup / Scene Control

SCENE SETUP

Mini one button remote control has built in 3 scene control which sends the

unique special command to the M series receiver to call already stored scene

memory from the receiver.

In another word, scene setup memory is stored in the M series receiver side so

each time a command is received from either mini key fob, mini one button

remote or handy scene remote the M series receiver will know to activate

whichever scene (1 / 2 / 3) to be called.

Because the memory is stored in the M series receiver so as long the M series

remote control has been paired with the M series receiver the scene command

will also work.

No need to reprogram each individual scene if you have 1 or more M series

remote control.

Single device setup with easy button remote control:

Scene 1

1. Function switch at position 1.

2. Set the desired load level status.

SCENE SETUP / SCENE CONTROL

10

Issue date: 21/01/2020

3. Slide function switch to position 3.

4. Press button once to store Scene Status 1.

5. Green LED flash 3 times →Amber LED flash 1 time to confirm Scene 1 is

stored.

Scene 2

1. Function switch at position 1.

2. Set the desired load level status.

LED 3 Times

LED 1 Time

SCENE SETUP / SCENE CONTROL