Arecont Vision D4SO Series Manuale utente

Arecont Vision D4SO Outdoor Dome Series Installation Manual

0 | Page

Arecont Vision D4SO Outdoor Dome Series Installation Manual

1 | Page

D4SO Outdoor Dome Installation Manual

A. Arecont Vision D4SO Dome Camera

Inside the box:

B. Mounting template

C. Security L-key

D. One double sided hex key

E. One single sided hex key

F. 6-position external power & IO plug

G. Pack of four (4) wood screws and four (4)

dry wall anchors

•#1 Phillips head screw driver

Not included but needed:

•#2 Phillips head screw driver

•Small Flat Head screw driver

Image 1

Mounting the Camera:

1. Remove camera and hardware from the

box.

2. Using the Mounting Template, prepare

the mounting provisions for camera

installation. NOTE: the 19.5mm diameter

hole on the Mounting template is where

the Ethernet cable will be exiting the

D4SO, align accordingly. If using the

side conduit hole, please see step 7

below.

3. Using Security L-key, loosen the four (4)

screws securing the dome cover (Image

2). Remove vandal resistant dome

cover. NOTE: Do not remove screws

from the dome cover.

Image 2

Arecont Vision D4SO Outdoor Dome Series Installation Manual

2 | Page

4. Run Ethernet cable through the hole on the

bottom of D4SO and plug it into the RJ45 port

on Arecont Vision’s compact MegaVideo®

camera. (Image 3) . NOTE: If the camera will

be powered via PoE, please skip to step 5.

Image 3

5. If the camera is powered by an outside power

supply, run power wires through the hole and

connect power wires to appropriate contacts

of 6-postion connector using small flat screw

driver and connect 6-position plug to camera

as shown in Image 4-1.

Note: Please make sure the polarity of the

AC/DC input on the camera match the way

wires are installed in connector shown in

Image 4-2.

Image 4-1

Image 4-2

6. Align the holes in the camera with the

prepared holes on the mounting surface.

Attach the camera to the mounting surface

with the wood screws or any optional

hardware suitable for the mounting surface.

Arecont Vision D4SO Outdoor Dome Series Installation Manual

3 | Page

7. If you are using the side conduit opening,

remove the conduit plug by first removing the

socket set screw using one of provided Allen

keys (Image 5).

Image 5

8. To adjust the tilt, use a #1 Phillips screwdriver

to loosen the screw on the side of the U

bracket 1/4 turn (Image 6). CAUTION: Do not

remove the screw!

Adjusting the Tilt and Pan:

Image 6

9. Adjust lens tilt as required and tighten the

screw. CAUTION: To properly install camera,

the U bracket needs to be installed between

the dome BASE and camera Bubble shown

in Image 7

Image 7

10. To adjust the pan, hold and turn the U bracket

as shown in Image 8.

Image 8

0°

90°

Screw

Gimbal Base

Pan=360°

U Bracket

Arecont Vision D4SO Outdoor Dome Series Installation Manual

4 | Page

11. To focus the lens, loosen the three set screws

as shown in Image 9and adjust each as

needed. Aadjusts the zoom, Badjusts the

iris, Cadjusts the focus.

Adjusting the Focus:

Note: Adjust zoom first then focus!

Note: For more information on proper

focusing technique, please watch the

“Focusing Arecont Vision Megapixel

Cameras” Best Practices Training Video at

www.youtube.com/ArecontVision.

12. Secure the dome cover to the camera.

13. Tighten the set screw on the dome cover.

14. Rotate bubble to align camera with slot in

camera shield.

15. Remove the protective film from the camera

dome. NOTE: be cautious not to scratch the

vandal dome cover.

Image 9

Arecont Vision D4SO Outdoor Dome Series Installation Manual

5 | Page

D4SO Pendant Mount (MD-CMT) Installation Instructions

A. Top shield

Inside the box:

B. Pendant Mount

C. Mounting template

D. Pack of four (4) machine screws

E. Pack of four (4) small machine screws

F. Pack of four (4) wood screws and four (4)

dry wall anchors

G. Large round rubber gasket

H. Smaller square rubber gasket

I. One double sided hex key

•#2 Phillips head screw driver

Not included but needed:

Image 10

1. Remove Pendant Mount and hardware from

the box.

Image 11 Image 12

2. Using the Mounting template, prepare the

mounting provisions for camera installation.

3. Place small gasket onto pendant dome as

shown in image 11.

4. Attach Dome to Pendant as shown in Image

12 using four machine screws provided.

5. Install large round rubber gasket onto

Pendant as shown in image 12. Be sure to

align the holes appropriately.

6. Run Ethernet Cable and outside power cable

(if necessary) through the Pendant.

7. Attach Pendant to the ceiling using the four

wood screws provided or any optional

hardware suitable for the mounting surface.

8. For installation of the camera, please

reference “Mounting the Camera”.

Arecont Vision D4SO Outdoor Dome Series Installation Manual

6 | Page

D4SO Wall Mount (MD-WMT2) Installation Instructions

MD-WMT2 only fits with SV-JBA and SV-EBA but

not with MD-JBA and MD-EBA!

Caution:

A. Wall mount ( Fit 1.5 NPT Standard)

Inside the box:

B. Top shield

C. Mounting template

D. One double sided hex key

E. Pack of four (4) machine screws

F. Pack of four (4) wood screws and four (4)

dry wall anchors

•#2 Phillips head screw driver

Not included but needed:

Image 13

1. Remove Wall Mount and hardware from the

box.

Image 14

2. Using the Mounting template, prepare the

mounting surface.

3. Install Top Shield on Wall Mount as shown in

image 14.

4. Fasten the socket set screw using double side

hex key.

5. Run Ethernet Cable and outside power cable

(if necessary) through the Wall Mount.

6. Attach Wall Mount to the wall using drywall

screws or any optional hardware suitable for

the mounting surface.

7. For installation of the camera, please

reference “Mounting the Camera”.

Arecont Vision D4SO Outdoor Dome Series Installation Manual

7 | Page

D4SO Wall Mount Cap (MD-CAP) Installation Instructions

A. Wall Mount Cap (MD-CAP)

Inside the box:

B. Pack of four (4) machine screws

•1½” NPT Pipe

Not included but needed:

•1½” NPT Coupling

•1½” NPT Flange

•#2 Phillips head screw driver

Image 15

1. Remove Wall Mount Cap from the box.

2. Assemble Wall Mount Cap, 1½” Coupling,

1½” Pipe nipple and 1½” Flange as a Pendant

Mount shown in image 16.

Image 16

3. Run Ethernet Cable and outside power cable

(if necessary) through the Pendant.

4. Attach Pendant to the ceiling using four wood

screws or any optional hardware suitable for

the mounting surface

5. For installation of the camera, please

reference “Mounting the Camera”.

MD-CAP

1 ½” Coupling

1 ½” Pipe

1 ½” Flange

Arecont Vision D4SO Outdoor Dome Series Installation Manual

8 | Page

D4SO Junction Box Adapter (MD-JBA) Installation Instruction

MD-JBA only fits with D4SO and MD-CMT but not

with MD-WMT2!

Caution:

A. Junction Box Adapter

Inside the box:

B. Large round rubber gasket

C. Pack of four (4) wood screws and four (4)

dry wall anchors

D. Pack of four (4) machine screws

E. One double sided hex key

•#2 Phillips head screw driver

Not included but needed:

•D4SO Wall Mount, MD-WMT

•¾” NPT Conduit (if necessary)

Image 17

1. Remove Junction Box and hardware from the

box

Image 18Image 19

2. Remove the conduit plug by first removing the

socket set screw using one of provided Allen

keys shown in Image 18.

3. Attach Junction Box Adapter to the wall using

drywall screws or any optional hardware

suitable for the mounting surface.

4. Attach D4SO Wall Mount to Junction Box

Adapter as shown in Image 19.

5. Connect ¾” NPT Conduit to Junction Box

Adapter

6. Run Ethernet Cable and outside power cable (if

necessary) through the Junction Box Adapter

and Wall Mount.

7. For installation of the camera, please

reference “Mounting the Camera”.

Arecont Vision D4SO Outdoor Dome Series Installation Manual

9 | Page

D4SO Junction Box Adapter (SV-JBA) for MD-WMT2 Installation Instruction

SV-JBA only fits with MD-WMT2 but not with D4SO

and MD-CMT!

Caution:

A. Junction Box Adapter

Inside the box:

B. Pack of four (4) machine screws

C. One double sided hex key

D. Pack of four (4) wood screws and four (4)

dry wall anchors

E. Large round rubber gasket

•#2 Phillips head screw driver

Not included but needed:

•D4SO Wall Mount, MD-WMT

•¾” NPT Conduit (if necessary)

Image 20

1. Remove Junction Box and hardware from the

box

Image 21

2. Remove the conduit plug by first removing the

socket set screw using one of provided Allen

keys.

3. Attach Junction Box Adapter to the wall using

drywall screws or any optional hardware

suitable for the mounting surface.

4. Attach D4SO Wall Mount to Junction Box

Adapter as shown in Image 21.

5. Connect ¾” NPT Conduit to Junction Box

Adapter.

6. Run Ethernet Cable and outside power cable (if

necessary) through the Junction Box Adapter

and Wall Mount.

7. For installation of the camera, please

reference “Mounting the Camera”.

Altri manuali per D4SO Series

Questo manuale è adatto per i seguenti modelli

Altri manuali Arecont Vision Telecamera di sicurezza

Arecont Vision

Arecont Vision MegaBall AV2245PM-W Manuale utente

Arecont Vision

Arecont Vision MegaDomeT Manuale utente

Arecont Vision

Arecont Vision SurroundVideo G5 Mini Manuale utente

Arecont Vision

Arecont Vision SurroundVideo Omni AV12176DN-08 Manuale utente

Arecont Vision

Arecont Vision D4S Series Manuale utente

Arecont Vision

Arecont Vision Megaball series Manuale utente

Arecont Vision

Arecont Vision MegaDome AV1355DN-1HK Manuale utente

Arecont Vision

Arecont Vision MicroDome AV1455DN-S Manuale utente

Arecont Vision

Arecont Vision ConteraIP Fisheye AV12CPD-236 Manuale utente

Arecont Vision

Arecont Vision MicroDome G2 AV1555DN-S Manuale utente

Arecont Vision

Arecont Vision Contera AV02CID-100 Manuale utente

Arecont Vision

Arecont Vision AV12ZMV-301 Manuale utente

Arecont Vision

Arecont Vision AV1255AM Manuale utente

Arecont Vision

Arecont Vision MegaDome 2 Manuale utente

Arecont Vision

Arecont Vision AV12975DN-NL Manuale utente

Arecont Vision

Arecont Vision H.264 Day/Night SurroundVideo Series Manuale utente

Arecont Vision

Arecont Vision AV08ZMV-300 Manuale utente

Arecont Vision

Arecont Vision MegaDome 2 Manuale utente

Arecont Vision

Arecont Vision MicroDome AV1455DN-F Manuale utente

Arecont Vision

Arecont Vision AV1215PM-S Manuale utente

Arecont Vision

Arecont Vision MicroDome AV2455DN-S Manuale utente

Arecont Vision

Arecont Vision D4S Series Manuale utente

Arecont Vision

Arecont Vision MegaView 2 AV1225PMIR-S Manuale utente

Arecont Vision

Arecont Vision megadome Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente